EEWORLDEEWORLDEEWORLD

Part Number

Search

M55342L06B62A6VTI

Description
Fixed Resistor, Thin Film, 0.15W, 62.6ohm, 50V, 0.1% +/-Tol, 200ppm/Cel, Surface Mount, 0805, CHIP
CategoryPassive components    The resistor   
File Size96KB,5 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

M55342L06B62A6VTI Overview

Fixed Resistor, Thin Film, 0.15W, 62.6ohm, 50V, 0.1% +/-Tol, 200ppm/Cel, Surface Mount, 0805, CHIP

M55342L06B62A6VTI Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid145087155970
package instructionSMT, 0805
Reach Compliance Codenot_compliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL7.7
Other featuresNON-INDUCTIVE
structureRectangular
JESD-609 codee0
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-65 °C
Package height0.8382 mm
Package length2.032 mm
Package formSMT
Package width1.27 mm
method of packingTR
Rated power dissipation(P)0.15 W
Rated temperature70 °C
GuidelineMIL-PRF-55342
resistance62.6 Ω
Resistor typeFIXED RESISTOR
size code0705
surface mountYES
technologyTHIN FILM
Temperature Coefficient200 ppm/°C
Terminal surfaceTin/Lead (Sn60Pb40) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage50 V
E/H (Military M/D55342)
www.vishay.com
Vishay Dale Thin Film
QPL MIL-PRF-55342 Qualified
Thin Film Resistor, Surface-Mount Chip
FEATURES
• Established reliability, “S” and “V” failure rate level
(10 ppm), C = 2
• High purity alumina substrate
• Wraparound termination featuring a tenacious adhesion
layer covered with an electroplated nickel barrier layer for
+150 °C operating conditions
LINKS TO ADDITIONAL RESOURCES
• Very low noise and voltage coefficient
(< -25 dB, 0.5 ppm/V)
• Non-inductive
• Laser-trimmed tolerances ± 0.1 %
• Wraparound resistance less than 0.010
Ω
typical
• In-lot tracking less than 5 ppm/°C
• Complete MIL-testing available in-house
• Antistatic waffle pack or tape and reel packaging available
• Military / aerospace / QPL
D
D
3
3
3D Models
Thin Film Mil chip resistors feature all sputtered wraparound
termination for excellent adhesion and dimensional
uniformity. They are ideal in applications requiring stringent
performance requirements. Established reliability is assured
through 100 % screening and extensive environmental lot
testing.
CONSTRUCTION
Passivation
Resistor Film
Solder
Coating
Nickel Barrier
High Purity
Alumina Substrate
Adhesion Layer
TYPICAL PERFORMANCE
ABSOLUTE
TCR
TOL.
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Resistance Range
TCR: Absolute
Tolerance: Absolute
Stability: Absolute
Stability: Ratio
Voltage Coefficient
Working Voltage
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability: Absolute
SPECIFICATIONS
Tamelox resistor film (passivated nichrome)
10
Ω
to 6.19 MΩ
± 25 ppm/°C to ± 300 ppm/°C
± 0.1 %, ± 0.25 %, ± 0.5 %, ± 1 %,
± 2 %, 5 %, ± 10 %
ΔR
± 0.02 %
-
0.1 ppm/V
30 V to 200 V
-65 °C to +150 °C
-65 °C to +150 °C
< - 25 dB
ΔR
± 0.01 %
CONDITIONS
-
-
-55 °C to +125 °C
+25 °C
2000 h at +70 °C
-
-
-
-
-
-
1 year at +25 °C
Revision: 15-Nov-2021
Document Number: 60018
1
For technical questions, contact:
thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Digitally controlled power supply using DSP for secondary voltage regulation
[[i] This post was last edited by lrz123 on 2011-10-25 10:48[/i]]...
lrz123 DIY/Open Source Hardware
About the digital tube display problem
I have been using FPGA to make a digital clock these days, using six digital tubes for display. I used a 20M crystal oscillator and divided it to get a 1KHZ signal, and used this signal to scan the bi...
gavin_8724 FPGA/CPLD
Power supply noise
I use lithium batteries to power a microcontroller through a switching step-down power supply to collect data from a vibration sensor. However, the noise from the power supply always affects the data ...
stuwang Power technology
Why are the first four bytes of a physical sector of an SD card or USB flash drive sometimes written as RRaA by the system?
I write an identifier to the physical sector of a USB flash drive through a filter driver I wrote. I write it starting from the first digit, for example "asdd12344". But sometimes for some reason, the...
hyhjjg Embedded System
Who loads the printer driver under WinCE? How to load it?
As the title says, who loads the printer driver under wince? GWES OR DEVICE? How to load it? Automatically load it when the computer is turned on or dynamically load it? Thanks for the answer....
fifthspace Embedded System
Graphic dot matrix LCD display module user manual
[i=s]This post was last edited by paulhyde on 2014-9-15 08:57[/i] Graphic dot matrix LCD display module user manual...
xfh168168 Electronics Design Contest

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1895  2040  2204  1339  833  39  42  45  27  17 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号