EEWORLDEEWORLDEEWORLD

Part Number

Search

800-012-07MT6-6SX

Description
Circular Connector
CategoryThe connector    The connector   
File Size1MB,5 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Environmental Compliance
Download Datasheet Parametric View All

800-012-07MT6-6SX Overview

Circular Connector

800-012-07MT6-6SX Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid7093063840
Reach Compliance Codecompliant
ECCN codeEAR99
Series 800 Mighty Mouse UN Mating Thread
PC Tail or Solder Cup PCB Receptacle
800-012 and 800-040 Ordering Information
Printed Circuit Board/ Solder Cup Receptacles
feature low profile shells for
minimum protrusion inside enclosures and integral board standoffs. Contacts are
non-removable.
Water Immersion, Unmated
Specify
800-012
connectors for applications where
open face water immersion is not a requirement. For MIL-STD-810 Method 512G
immersion requirements, specify
800-040
watertight connectors . These 800-040
connectors are specially sealed (“MOD-518”) and are 100% tested to maintain a
helium leak rate of 1 x 10
-4
cc/second at one atmosphere pressure differential from
-40C to +70C.
How To Order
C
Shell
Size
Series 800
Sample Part Number
Series
Shell Style (See Table I)
-02
= Square Flange
Shell Material and Finish
Shell Size - Insert
Arrangement
Contact Type
Shell Key Position
(See Table II)
P
= Pin, PC Tail
S
= Socket , PC Tail
N
= Normal
800-012
800-012
=
Receptacle for Solder Cup or PCB Termination, with Standard
Epoxy Potting
800-040
=
Receptacle for Solder Cup or PCB Termination, With Special
“MOD-518” Sealing For Open Face (Unmated) Water Immersion
Requirements. 100% Leak Tested.
-07
= Jam Nut
(See
Jam Nut Panel Cutout Dimensions Page C-3)
C
= Aluminum / Black Anodize (Non-Conductive) RoHS Compliant
M
= Aluminum / Electroless Nickel RoHS Compliant
NF
= Aluminum / Cadmium with Olive Drab Chromate
ZNU
= Aluminum / Zinc-Nickel with Black Chromate
MT
= Aluminum / Nickel-PTFE RoHS Compliant
Z1
= Stainless Steel / Passivated RoHS Compliant
See Contact Arrangements page C-2
E
= Pin, Solder Cup
F
= Socket, Solder Cup
Y
= Pos. Y
Z
= Pos. Z
-07
M
7-10
P
Z
X
= Pos. X
Table I: Shell Style
ØM
in
.318
.386
.449
.510
.574
.635
.760
mm
8.08
9.80
11.40
12.95
14.58
16.13
19.30
Recommended Panel Cut Out
N Flat ± .002
in
.297/.292
.365/.360
.429/.424
.483
.540
.614
.722
mm
7.54/7.42
9.27/9.14
10.90/10.77
12.67
13.71
15.60
18.34
øM
N FLAT
-02
Square Flange Front Mount
-07
Jam Nut for Rear Panel
Mounting
5
6
7
8
9
10
12
Dimensions in Inches (millimeters) are subject to change without notice.
© 2014 Glenair, Inc.
Series 80 Mighty Mouse
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
C-12
E-Mail: sales@glenair.com
PCB design considerations
PCB design considerations 1. Overlapping pads Overlapping pads (except surface mount pads), that is, overlapping holes, will cause drill bits to break and wires to be damaged due to multiple holes in ...
fighting Analog electronics
Open a discussion forum about blood glucose meter. If you want to learn STM8, please buy it and join in the fun.
[i=s]This post was last edited by weizhongc on 2015-12-3 13:34[/i] [url=https://bbs.eeworld.com.cn/thread-477418-1-1.html]https://bbs.eeworld.com.cn/thread-477418-1-1.html[/url] Purchase link: [url=ht...
weizhongc stm32/stm8
cc2530
I bought a small network management board for CC2530 and two node boards (both Tinyos and Z_stack data are available) from E-Dave Electronics before. I am trying to sell or exchange them. If you are i...
568760310 Buy&Sell
PLC1769 library functions
I'm working on PLC1769 recently. Is there any library function description for this? ??? ??? ???...
asd1126163471 NXP MCU
ActiveSync synchronization issues
I am using a WINCE5.0 device. There are two USB ports on the PC. Now one USB port can be connected normally, but when I switch to the other USB port of the PC, it cannot be connected. I reinstall the ...
chenmo Embedded System
Please advise on the following simulation
Now I have done it and the functional simulation is fine. But the problem is how do I get the TH TCO parameters I read in the book? I know the formulas, and what timing constraints are considered good...
eeleader-mcu FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1724  2666  2621  1222  802  35  54  53  25  17 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号