8N4Q001EG-0052CDI8 datasheet, PDF

Datasheet> All Categories > semiconductor> Analog mixed-signal IC> 8N4Q001EG-0052CDI8

8N4Q001EG-0052CDI8: DescriptionIC osc clock QD freq 10clcc; Categorysemiconductor Analog mixed-signal IC; File Size163KB，20 Pages; ManufacturerIDT (Integrated Device Technology, Inc.); Websitehttp://www.idt.com/

Download Datasheet View All

8N4Q001EG-0052CDI8 Online Shopping

Suppliers	Part Number	Price	MOQ	In stock
	8N4Q001EG-0052CDI8	-	-	View	Buy Now

8N4Q001EG-0052CDI8 Overview

IC osc clock QD freq 10clcc

Preview

Download Datasheet

View All

Quad-Frequency Programmable XO IDT8N4Q001 REV G

DATA SHEET

General Description

The IDT8N4Q001 is a Quad-Frequency Programmable Clock

Oscillator with very flexible frequency programming capabilities. The

device uses IDT’s fourth generation FemtoClock® NG technology for

an optimum high clock frequency and low phase noise performance.

The device accepts 2.5V or 3.3V supply and is packaged in a small,

lead-free (RoHS 6) 10-lead ceramic 5mm x 7mm x 1.55mm package.

Besides the four default power-up frequencies set by the FSEL0 and

FSEL1 pins, the IDT8N4Q001 can be programmed via the I

interface to output clock frequencies between 15.476MHz to

866.67MHz and from 975MHz to 1,300MHz to a very high degree of

precision with a frequency step size of 435.9Hz ÷

(N is the PLL

output divider). Since the FSEL0 and FSEL1 pins are mapped to four

independent PLL divider registers (P, MINT, MFRAC and N),

reprogramming those registers to other frequencies under control of

FSEL0 and FSEL1 is supported. The extended temperature range

supports wireless infrastructure, telecommunication and networking

end equipment requirements.

Features

•

Fourth generation FemtoClock® NG technology

Programmable clock output frequency from 15.476MHz to

866.67MHz and from 975MHz to 1,300MHz

Four power-up default frequencies (see part number order

codes), re-programmable by I

C programming interface for the output clock frequency and

internal PLL control registers

Frequency programming resolution is 435.9Hz ÷N

One 2.5V, 3.3V LVDS clock output

Two control inputs for the power-up default frequency

LVCMOS/LVTTL compatible control inputs

RMS phase jitter @ 156.25MHz (12kHz - 20MHz): 0.253ps

(typical), integer PLL feedback configuration

RMS phase jitter @ 156.25MHz (1kHz - 40MHz): 0.263ps

(typical), integer PLL feedback configuration

Full 2.5V or 3.3V supply modes

-40°C to 85°C ambient operating temperature

Available in Lead-free (RoHS 6) package

Block Diagram

OSC

XTAL

÷MINT,

MFRAC

FSEL1

FSEL0

SCLK

SDATA

Pulldown

Pullup

Pin Assignment

÷P

PFD

LPF

FemtoClock® NG

VCO

1950-2600MHz

÷N

Q

DNU 1

OE 2

GND 3

FSEL0 4

FSEL1 5

10 SCLK

9 SDATA

8 V

7 nQ

6 Q

Configuration Register (ROM)

(Frequency, APR, Polarity)

C Control

IDT8N4Q001

10-lead ceramic 5mm x 7mm x 1.55mm

package body

CD Package

Top View

IDT8N4Q001GCD

REVISION A

MARCH 6, 2012

Recommended Resources

Four-channel 64G linear modulator driver chip, do you know?

Combination of source ground and emitter follower

Isolated zero-crossing AC switch circuit

YN5203-M6 decoding circuit

555 crystal diode and transistor quality detector circuit

Special application circuits for operational amplifiers

A development board given away at MCU Day today: When I participated in TI MCU Day, I was given a development board, which is said to be able to be used as a jtag emulator, dual function!!!...; expressme Microcontroller MCU

28075 xBAR's question: 28075 has 8 Output X-BARs. Each Output X-BAR has 32 x 4 input signals, theoretically 128 input signals in total. Are the 128 input signals of the 8 Output X-BARs exactly the same? I can't see the diff...; Airwill Microcontroller MCU

Notice: The new markdown editor is now online!!: Hi, everyone! There are new changes in our forum. The markdown editor was launched this week. Netizens who like to write articles in markdown can use it happily! ! The specific location of the markdow...; okhxyyo Suggestions & Announcements

Power control circuit: Hello everyone! Please give me your advice on the power control circuit shown in the picture; mainly how do the MOS tube, triode, and each diode in the circuit work?...; Gjinbiao Power technology

Have you ever seen such a power supply output ripple? It's like a modulated signal. How to deal with it?: [color=#000][font=微软雅黑][size=3]The first waveform has a low-frequency interference. Without interference, the ripple of the power supply will be smaller. [/size][/font][/color] [font=微软雅黑][size=3][/si...; jadystone Analogue and Mixed Signal

Frequency doubling circuit: I am currently working on a frequency doubling circuit. I simulated it with simulation software at first and there was no problem. However, after making the actual circuit, no matter how the input fre...; HT001 Analog electronics

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components