Fref0 Frequency Selection .................................................................................................................................................................10
Fref1 Frequency Selection .................................................................................................................................................................10
C2/C1.5 Output Frequency Control....................................................................................................................................................14
3
IDT82V3155 ENHANCED T1/E1/OC3 WAN PLL WITH DUAL REFERENCE INPUTS
State Control Circuit ............................................................................................................................................................................ 9
State Control Diagram......................................................................................................................................................................... 9
TIE Control Block Diagram................................................................................................................................................................ 11
Reference Switch with TIE Control Block Enabled............................................................................................................................ 12
Reference Switch with TIE Control Block Disabled........................................................................................................................... 12
Input Control Setup and Hold Timing ................................................................................................................................................ 29
4
IDT82V3155 ENHANCED T1/E1/OC3 WAN PLL WITH DUAL REFERENCE INPUTS
2.1 State Control Circuit ..................................................................................................................................................................................9
2.1.1 Normal Mode..............................................................................................................................................................................10
2.1.2 Fast Lock Mode..........................................................................................................................................................................10
2.2 Frequency Select Circuit .........................................................................................................................................................................10
2.5 Invalid Input Signal Detection ..................................................................................................................................................................11
2.6 TIE Control Block.....................................................................................................................................................................................11
2.7.5 Digital Control Oscillator (DCO)..................................................................................................................................................13
Measures of Performance ...............................................................................................................................................................................15
3.3 Jitter Transfer ..........................................................................................................................................................................................15
3.4 Frequency Accuracy................................................................................................................................................................................15
3.6 Capture Range ........................................................................................................................................................................................15
3.7 Lock Range .............................................................................................................................................................................................15
3.9 Time Interval Error (TIE)..........................................................................................................................................................................15
3.10 Maximum Time Interval Error (MTIE) ......................................................................................................................................................15
Absolute Maximum Ratings ............................................................................................................................................................................17
Recommended DC Operating Conditions .....................................................................................................................................................17
DC Electrical Characteristics ..........................................................................................................................................................................17
6.1 Single End Input/Output Port...................................................................................................................................................................17
6.2 Differential Output Port (LVDS) ...............................................................................................................................................................18
AC Electrical Characteristics .........................................................................................................................................................................19
I made my own board based on the Ulong 2440+ standard ce5 development board, and used your method to upgrade the SDRAM to 128M. The system can boot, but the SD card cannot be recognized after booting,...
The power supply rejection ratio (PSRR) describes how well an operational amplifier rejects changes in the power supply voltage. PSRR is defined as the degree of offset per volt of power supply voltag...
Can we arrange data transmission in a task, and when we need to send data to the host computer, we should turn off the interrupt first, and then turn on the interrupt after the transmission is complet...
I found that there is a feature when the phone is turned on: 1. When it is turned off, long press the power button to turn it on normally 2. When it is turned off, plug in the USB to charge and it wil...
introduction
Since the beginning of the 21st century, the world of information has changed rapidly. Maybe a high-tech product will be released today and a better similar product will be releas...[Details]
introduction
1 The significance of using RTOS on MSP430
It is understandable that it is meaningless to use RTOS on MSP430. Because the hardware resources of MSP430 are limited (for exampl...[Details]
The Mobile Industry Processor Interface (MIPI) Alliance is an organization responsible for promoting the standardization of software and hardware in mobile devices. It has released the D-PHY specif...[Details]
1 Introduction
Ultrasonic waves have strong directivity, slow energy consumption, and can propagate over long distances in a medium, so they are used for distance measurement. Ultrasonic detec...[Details]
Capacitance Measurement
Used to verify that capacitors meet the manufacturer's specifications. For quality control, a group of capacitors may be placed in an environmental chamber and the cap...[Details]
Introduction
Automakers are working to reduce vehicle weight to reduce CO2 emissions and improve fuel efficiency. Designers are therefore seeking new technologies and design techniques that can...[Details]
The TPS92210 is a single-stage LED lighting pulse width modulation (PWM) controller. The TRIAC dimmable solution not only regulates the LED current, but also achieves a power factor close to 1. The...[Details]
Only a small number of LED manufacturers can produce high-quality LEDs. For applications that are only used for simple indication, low-quality LEDs are sufficient. However, high-quality LEDs must...[Details]
1. Introduction
With the increasing popularity of fully automatic washing machines, consumers have higher and higher requirements for their environmenta...[Details]
Introduction
In industrial control, speed measurement is often required. Generally, a contact tachometer is used. This tachometer must be placed against the center of the shaft to measure. It...[Details]
1 Introduction
Ultrasound refers to elastic vibration with a frequency higher than the audible frequency limit (i.e., in the frequency band above 20 kHz). The propagation process of this vib...[Details]
The invention of the steam engine ushered in the first conversion of internal energy and mechanical energy for mankind, and the birth of the internal combustion engine at the end of the 19th centur...[Details]
introduction
LEDs continue to gain popularity in automotive applications, thanks to their long lifespan and the flexibility they offer for body styling and interior design. Some may be surpris...[Details]
Car lights, whether headlights, fog lights or tail lights, play an important role in driving safety. However, the material of the car lights determines that the probability of damage in a collision...[Details]