EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-NLPSC2805

Description
Transponder, SC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerLumentum Operations LLC
Download Datasheet Parametric View All

PH1-NLPSC2805 Overview

Transponder, SC/UPC Connector,

PH1-NLPSC2805 Parametric

Parameter NameAttribute value
Objectid4000969650
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Communication standardsOC-192, SONET
Connection TypeSC/UPC CONNECTOR
Emitter/Detector TypePIN PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1533 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-17 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Can any expert help me see why the AD acquisition result of STC12c5410ad is always 00?
STC12c5410ad, why is the AD acquisition result always 0? #include "reg51.h"#include "intrins.h"#include "164.h"#include "math.h"typedef unsigned char BYTE;typedef unsigned int WORD;#define uchar unsig...
SHT112 MCU
Access to large amounts of data files
What I want to achieve is to store short messages in the T card, the purpose is to achieve unlimited storage of information! The key to the problem is performance. Because it is stored in a mobile sto...
cchaonjust Embedded System
NAND flash bad block processing problem
I am using nand flash-SAMSUNG_K9K8G08U0A for the first time. The PDF mentioned that I need to monitor the bad blocks first and then generate a table. How do I generate the table? After generating the ...
wangyurui Embedded System
When operating IIC devices such as AT24C256, is it done bit by bit or byte by byte?
I saw that some routines operate the reading and writing of AT24C256 bit by bit, as follows: unsigned char read_CharData(void) { unsigned char num,tmp=0x80,i2crecv=0x00; for(num=0;num <8;num++) { SDA1...
shiftwu Embedded System
This week's highlights
[b][url=http://www.deyisupport.com/blog/b/power_house/archive/2018/01/03/52800.aspx][font=微软雅黑][size=4]How to get started with power supply design[/size][/font][/url][/b][font=微软雅黑][size=4] [/size][/f...
橙色凯 Analogue and Mixed Signal
When using AD copper plating, how to add the same solder layer?
[backcolor=rgb(239, 245, 249)]Hi everyone, I am using AD15. After I apply copper to my area, I want to open a window, that is, add another layer of solder on top. What method can be used to achieve th...
万年长山 PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 558  2262  2042  2152  1957  12  46  42  44  40 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号