EEWORLDEEWORLDEEWORLD

Part Number

Search

177-740-2-67GP6J5-18BXG

Description
Cable Assembly, 26AWG,
CategoryThe connector    Connector bracket   
File Size858KB,5 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Environmental Compliance
Download Datasheet Parametric View All

177-740-2-67GP6J5-18BXG Overview

Cable Assembly, 26AWG,

177-740-2-67GP6J5-18BXG Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid7005062955
Reach Compliance Codecompliant
Country Of OriginUSA
YTEOL8.75
Other featuresSTANDARD: MIL-DTL-83513, EMI SHIELDED
CertificationMIL
Conductor surface treatmentSILVER
conductor materialCOPPER
ConnectorSide1MICRO-D MALE
ConnectorSide2MICRO-D MALE
Connector bracket typeCABLE ASSEMBLY
structureSTRANDED
Cross-sectional area0.129 mm2
DIN complianceNO
IEC complianceNO
insulator materialCROSSLINKED ETHYLENE-TETRAFLUOROETHYLENE
length0.466 mm
MIL complianceYES
Number of conductors67
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Rated current3 A
Rated voltage150 V
resistance0.147 Ω
shieldYES
stay19X38
Wire gauge26 AWG
Wire and Cable NamesFLEXIBLE CORD AND FIXTURE WIRE
B
SHIELDING EFFECTIVENESS (Db)
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
SHIELDING EFFECTIVENESS (Db)
Micro-D Harness
EMI Performance with Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
MWDM Micro-D
Shielded Cable Assembly
Single-Ended or Double-Ended–These
easy-to-order cable
assemblies eliminate the need for expensive assembly labor. 100%
tested and ready for use.
Now With Twisted Pairs–No
need to create a procurement
specification for Micro-D cables with twisted pairs. Glenair 177-740
cables are furnished with a full complement of white/blue twisted
pair wires.
Integral Shield Termination–The
connector shell has a platform
to accept Band-It shield termination bands. The cable shield braid is
attached directly to the connector.
Save Labor, Reduce Weight and Improve EMI Shielding
with Glenair’s Micro-D Shielded Cable Assemblies
Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s
fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-
piece connector shell and secured with a stainless steel
Band-Master™ ATS
clamp. These pre-wired, 100% tested
assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low
shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be
ordered in any length, either single-ended or “back-to-back”.
Ground Spring and EMI Shielding Effectiveness
A gold-plated stainless steel ground spring on the pin connector mating
face offers substantial improvement in EMI protection. The graphs
compare identical connectors tested with and without ground springs.
EMI Performance without Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
frequency (Hz)
frequency (Hz)
© 2013 Glenair, Inc.
High Performance Micro-D Connectors and Cables
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
B-14
E-Mail: sales@glenair.com
I don't understand a section of ARM assembly code, please give me some advice.
IMPORT |Image$$RO$$Limit| IMPORT |Image$$RW$$Base| IMPORT |Image$$ZI$$Base| IMPORT |Image$$ZI$$Limit| When writing C code on the development board, the ARM assembler must be initialized before the C c...
ldfree ARM Technology
About the latch pin of the NADV connection latch of stm32f103VE
I saw the truth table of a general latch like this, and my NADV is connected to the C pin.Then I saw the timing diagram of the multiplexing mode of FSMCI would like to ask, if I connect it like this, ...
chonchie stm32/stm8
Why should small capacitors be placed close to the circuit when decoupling the power supply?
When decoupling the power supply, it is usually achieved by using a small capacitor and a large capacitor. But why must the small capacitor be as close to the circuit as possible and the wiring as sho...
Grizabella Analog electronics
Max32630 (III) - OLED screen display time
[i=s]This post was last edited by 29447945 on 2017-9-13 18:57[/i] An OLED display screen has been adjusted for a long time, and it can finally display today. I have two screens, one for SPI communicat...
29447945 DIY/Open Source Hardware
Serial communication based on stm32 code implementation
Serial communication is a very common communication method, with a small number of cables and simple operation. Let's take a look at the definition, principle and code implementation of serial communi...
Aguilera Microcontroller MCU
TOC problems encountered during NBoot
During the NBoot startup process, it is necessary to access the contents of block1 in NandFlash. The contents of block1 are the TOC of EBoot to be loaded next. How is the TOC of EBoot burned into nand...
sdx_none Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2209  2031  1763  61  1957  45  41  36  2  40 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号