General Electrical, Physical, and Environmental Characteristics
Test Procedures:
Section J of the catalog covers the
applicable test procedures
Humidity Test:
The Non-Hermetically sealed units shall be
tested as outlined in section J “Humidity Test”
As a result of the test there shall be:
• No visible damage
• Max.
∆
C of ± 5%
• Min. IR = 50% of initial limit
• Max. DF = .5%
Electrical Characteristics:
Capacitance, Dissipation Factor, Insulation
Resistance, and Dielectric Strength shall be
measured as specified in section J.
Physical Characteristics:
The Lead Strength shall be measured as
specified in section J.
DC Life:
810P, 820P, 842P & 860P: 140% of rated voltage at 125°C for 250 hours.
832P & 880P: 125% of rated voltage at 150C for 250 hours.
882P: 125% of rated voltage for 250 hours at 125C.
As a result of the test there shall be:
• No permanent open or short circuit
Environmental Characteristics:
Vibration Test: (Condition B)
No mechanical damage, short, open or
intermittent circuit
• No visible damage
• Max.
∆
C of ± 5%
• Min. IR = 50% of initial limit
Moisture Resistance:
The hermetically sealed units shall be tested
as outlined in the Moisture Resistance testing
of section J.
As a result of the test there shall be:
• No visible damage
• Max.
∆
C of ± 5%
• Min. IR = 50% of initial limit
• Max. DF = .5%
• Max. DF = 0.3%
AC Life:
The 859P shall be tested at 110% of the
rated rms voltage at 400 Hz for 250 hours at 85°C.
As a result of the test there shall be:
• No permanent open or short circuit
• No visible damage
• Max.
∆
C of ± 5%
• Min. IR = 50% of initial limit
• Max. DF = 0.5%
F-2
electronics
,
inc.
METALIZED POLYPHENYLENE SULFIDE FILM CAPACITORS
F3
electronics
,
inc.
POLYPHENYLENE SULFIDE FILM CAPACITORS
STYLES FOR METAL-CASE FILM CAPACITORS
SECTION GROUNDED TO CASE
SECTION INSULATED FROM CASE
DIMENSIONS IN INCHES
DIMENSIONS IN INCHES
CASE STYLE 01
+1.00
-0
1.625
CASE STYLE 02
±0.031
0.172 MAX
L
±0.031
+1.00
-0
1.625
0.172
MAX
1.625
+1.00
-0.00
L
D
-0.005
±0.015
DIA
D
+0.015
-0.005
CASE STYLE 04
+1.00
-0
1.625
±0.015
0.020
1.625
+1.000
-0.000
CASE STYLE 03
+1.00
-0
1.625
±0.015
0.020
L
±0.062
L
±0.31
0.020
±0.015
0.172
MAX
0.172
MAX
INSULATING SLEEVE
0.0075 MAX THICKNESS
D
+0.015
-0.005
D
+0.015
-0.037 DIA.
INSULATING SLEEVE
0.0075 MAX THICKNESS
CASE STYLE 12
1.625
+1.00
-0
CASE STYLE 13
1.625
+1.00
-0
1.625
+1.000
-0.000
WRAP-AROUND
APPROX. 135°
FOR 0.400 DIA.,
AND APPROX.
225° FOR LARGER DIA.
DIA
0.172
MAX
L
D
±0.031
L
±0.031
+0.015 DIA
-0.005
C
L
0.172
MAX
C
L
D
-0.005
±0.015
A
±0.005
DIA
C B
W
±0.015
0.033
±0.005
FOR 0.400 DIA.,
0.051
±0.005
FOR DIA. 0.500
AND LARGER
±0.005
A
DIA
C B
W
±0.015
0.033
±0.005
FOR 0.400
DIA., 0.051
±0.005
FOR
DIA. 0.500 AND LARGER
Bracket Dimensions (Style 12 & 13)
Inches
D
0.400
0.500
0.562
0.670
0.750
1.000
W
0.250
0.500
0.500
0.500
0.500
0.500
A
0.144
0.156
0.156
0.156
0.156
0.156
B
0.187±0.015
0.250±0.031
0.250±0.031
0.250±0.031
0.250±0.031
0.250±0.031
C
0.312±0.031
0.437±0.062
0.437±0.062
0.437±0.062
0.437±0.062
0.437±0.062
dimensionsbrac style 12 and 13
F4
electronics
,
inc.
POLYPHENYLENE SULFIDE FILM CAPACITORS
TYPICAL TAB TERMINAL DIMENSIONS
0.020
c
L
±0.005
0.125
±0.015
c
L
SLOT 0.062 x 0.125
A
B
0.296
±0.062
Dwg. No A-9525
A = 0.156 ± 0.015" (3.96 ± 0.38mm)
B = 0.187 ± 0.015" (4.75 ± 0.38mm)
Tab Terminal available only on case diameters equal to or greater than 0.400 inches.
T1 & T3 s t y l e s a r e s u p p l i e d w i t h o n e t a b t e r m i n a l o n t h e i n s u l a t e d e n d a n d a g r o u n d lead on the opposite end.
CATALOG NUMBERING SYSTEM
EXAMPLE:
859P
183
X9
165
S
02
STYLE NUMBER.
SEE PAGE 4 FOR STYLE VARIATIONS
AND CORRESPONDING DIMENSIONS. (Metal case only)
TERMINAL.
S = WIRE LEADS, T = SOLDERING TAB*
*SOLDERING TABS ARE A VAILABLE ONLY ON CASE
DIAMETERS EQUAL TO OR GREATER THAN 0.400
INCHES. (Metal case only)
AC or DC VOLTAGE RATING.
EXPRESSED IN VOLTS. SEE STANDARD
RATINGS CHARTS FOR VOLTAGE CODE.
CAPACITANCE TOLERANCE.
X0 = ±20%; X9 = ±10%
X5 = ± 5%; X2 = ±2%
X1 = ± 1%
CAPACITANCE.
EXPRESSED IN PICOFARADS. THE FIRST TWO DIGITS ARE SIGNIFICANT
FIGURES; THE THIRD IS THE NUMBER OF ZEROS FOLLOWING. SEE STANDARD RATINGS
TABLES FOR CAP ACITANCE CODE. e.g. 183 = 18000pf or 0.018µf
Contents: 1 Introduction to Digital Logic 1.1 Digital Circuits and Digital Signals 1.2 Number Systems 1.3 Arithmetic Operations on Binary Numbers 1.4 Binary Codes 1.5 Binary Logic Variables and Basic ...
For example, the instrument manual says the start bit is (02), so how do you determine that 2 is the start bit? ? What if there is also data 2 in the middle, for example, the data sent is: 222222222...
[i=s] This post was last edited by Pinghu Qiuyue on 2014-5-27 09:50 [/i] I asked someone to make an expansion board for C2000 LaunchPad. I will show it to you in a few days. You can do general experim...
[table=98%,rgb(239, 245, 249)] [tr][td]Hi everyone, the address I burned the kernel to is 0x200000, but there is a bad block at 0x280000. When I boot, it prompts bad CRC and cannot find the kernel. I ...
I am working on a project that requires the output of 512 square waves, where the frequency of the square wave is adjustable in 10 levels between 1Mhz and 1Hz. The frequency of every two channels is t...
PV DC fuses are safety devices used to protect PV panels, inverters, and DC loads. To ensure their safety and reliability, they must be UL248 certified.
Before applying for UL248 certifi...[Details]
Tesla and BYD, vying for dominance in the global electric vehicle market, are reportedly considering adopting Samsung's AMOLED (active-matrix organic light-emitting diode) technology for their next...[Details]
Reflow soldering, a common soldering method in modern electronics manufacturing, primarily melts solder paste and pads to form solder joints. With technological advancements, soldering equipment ha...[Details]
introduction
With the development of digital and network technologies, broadcasting technology has become increasingly diversified, with the most significant trend being the transition from an...[Details]
Electric vehicles are currently gaining momentum, but this is just a facade. Fuel-powered vehicles remain unchallenged. While electric vehicles boast unique advantages in environmental emissions an...[Details]
As the number of cars increases, environmental pressures are also increasing. At this time, some people are saying that new energy vehicles are energy-efficient and environmentally friendly, and ar...[Details]
Electric motors and internal combustion engines of the same power have similar torque levels. High power requires high torque, and torque determines a vehicle's acceleration speed, commonly known a...[Details]
For healthcare professionals, accurate diagnosis and treatment are crucial for a clear picture of a person's health. However, healthcare professionals often rely on tests at medical facilities, cli...[Details]
On August 22nd, Lantu Motors unveiled a new technology called "Lanhai Intelligent Hybrid" during a live broadcast of CCTV News' "Top Laboratory." The name sounds like another new term, but a closer...[Details]
Gross profit margin jumped from 13.6% in the first half of last year to 25.9%, almost doubling year-on-year.
On August 21, RoboSense released its interim performance report, in which the...[Details]
With the rapid advancement of automation technology, collaboration between robots is no longer just science fiction. Imagine dozens of machines moving goods in a warehouse without interfering with ...[Details]
On August 22, South Korean media Nate reported on the 20th local time that Samsung Electronics is introducing Hyper Cell technology into its most advanced 2nm process technology, striving to improv...[Details]
Overview
As handheld voice communication devices become more and more popular, they are increasingly used in noisy environments, such as airports, busy roads, crowded bars, etc. In such noisy ...[Details]
SMT placement machines are important equipment in surface mount technology (Surface Mount Technology). Their performance has a decisive impact on the quality and efficiency of electronic manufactur...[Details]
PowiGaN achieves 95% efficiency at both light and full loads, meeting critical operational and safety requirements.
DARWIN, Australia and SAN JOSE, Calif.,
August 22, 2025 – Powe...[Details]
Analog electronics
京公网安备 11010802033920号
EEWORLD
