EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

AR02DTD2742

Description
Fixed Resistor, Thin Film, 0.5W, 27400ohm, 150V, 0.5% +/-Tol, 50ppm/Cel, Surface Mount, 2512, CHIP
CategoryPassive components    The resistor   
File Size466KB,8 Pages
ManufacturerViking Tech Corp
Environmental Compliance
Download Datasheet Parametric View All

AR02DTD2742 Overview

Fixed Resistor, Thin Film, 0.5W, 27400ohm, 150V, 0.5% +/-Tol, 50ppm/Cel, Surface Mount, 2512, CHIP

AR02DTD2742 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid7252302261
package instructionSMT, 0402
Reach Compliance Codecompliant
Country Of OriginTaiwan
ECCN codeEAR99
YTEOL8.75
Other featuresPRECISION
structureRectangular
JESD-609 codee3
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.3 mm
Package length1 mm
Package shapeRECTANGULAR PACKAGE
Package formSMT
Package width0.5 mm
method of packingTR, PAPER, 7 INCH
Rated power dissipation(P)0.0625 W
Rated temperature70 °C
resistance27400 Ω
Resistor typeFIXED RESISTOR
size code0402
surface mountYES
technologyTHIN FILM
Temperature Coefficient50 ppm/°C
Terminal surfaceTin (Sn) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance0.5%
Operating Voltage50 V
uCOS-II V2.86 migration based on LM3S9B96
Single task: blinking LED;LED/IO: PF3;Directly onto the program: Mainly based on the LM3S9B92 based uCOSII V2.86 porting, hope it will be helpful to beginners!...
xylq0826 Microcontroller MCU
Using ir2110 driver to make a buck circuit
I want to make a BUCK circuit, I am new to switching power supply. I designed a circuit diagram, can you help me see if it is feasible? I haven't configured the parameters yet. Mainly, is it okay to u...
光芒。 Switching Power Supply Study Group
Methods for solving faults in FPGA design and development based on EDA simulation technology.pdf
Methods for solving faults in FPGA design and development based on EDA simulation technology.pdf...
zxopenljx FPGA/CPLD
STM32 smart card issue
In STM32's serial smart card mode, how should it be connected? The manual says that TX and SW_RX should be connected together, so which pin is SW_RX?...
使者0123 stm32/stm8
How to use the lithium battery charge and discharge management IC AP5900A?
1. Does anyone know if the IC AP5900A is suitable for the charging and discharging circuit of a single 3.7V lithium battery? The specification is not very clear, and it would be best if I could provid...
飓风狂飙 LED Zone
STM8S207 cannot run at 24MHz, the CPU can only divide by 2?
//Using external crystal oscillator 24MHz, 1 division does not work, 2 division can work normally, I don't know which setting is wrongvoid Clk_Config(void){ErrorStatus val;CLK_DeInit();//CLK_HSECmd(EN...
ryg7 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2047  1598  99  296  1354  42  33  2  6  28 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号