The waveform after mixing two same-phase sine wave signals through the multiplication chip AD633 must have a DC component, right? How to separate the DC component? The waveform obtained by the ring di...
Inductive proximity sensors can be used for contactless detection of metal near LC sensors. These inductive sensing solutions enable presence detection and task counting on factory assembly lines with...
I searched online, but to no avail:Sad: For example:Here, CLK_counter increments by 1 for each input clock cycle, but I think there is a problem and want to observe this signal. The TestBench automati...
[align=left]Hello experts, I am analyzing the openpilot source code and found the following code: [/align][align=left][font=新宋体]OPLinkSettingsData oplinkSettings;[/font][/align][align=left][font=新宋体] ...
The oscilloscope is normal and can see the scan lines. However, when observing the measured signal, only the scan lines can be seen but not the waveform. Why is this?...
[i=s] This post was last edited by lb8820265 on 2017-4-22 12:47 [/i] [align=left][font=微软雅黑][size=3]First, here is the video: [/size][/font][/align][align=left][align=center][font=微软雅黑][size=3][media=...
Microchip's PIC18F46J50 is a low-power, high-performance 8-bit USB microcontroller (MCU) using nanoWatt XLP technology. The current in deep sleep mode can be as low as 13nA, the operating voltage i...[Details]
The Portable Digital Data Acquisition System (PDDAS) uses LabVIEW Real-Time and PXI to control the wind tunnel test and record air pressure data from 128 different channels.
"The LabVIEW Real-...[Details]
Introduction
Power subsystems are becoming more and more integrated into the overall system. Power systems have moved from being separate "essential dangerous devices" to being monitorable...[Details]
Two simple circuits are implemented to drive two LEDs from a battery powered microprocessor.
This design is based on a circuit that uses three resistors and a microprocessor I/O pin as an input h...[Details]
The data collector of the automatic weather station is generally designed based on a single-chip microcomputer or a PC/104 bus controller. It has the characteristics of good compatibility with PC, low...[Details]
1. Introduction
With the gradual automation and modernization of industrial control systems, fieldbus control systems have received more and more attention and application. CAN bus is currentl...[Details]
Microcalorimetry
is used to determine energy relationships. Microcalorimetry techniques are often required when performing calorimetric experiments with small sample sizes or slow heating rat...[Details]
1 Introduction
The Third Steel Plant of Jigang Group is a key investment project of Jigang Group during the "15th Five-Year Plan". It has introduced first-class domestic and foreign advanced eq...[Details]
As a simple and practical input device, buttons have been used in various microcontroller application systems and are ubiquitous. However, the buttons used in different practical occasions are also...[Details]
Experimental tasks
A DS18B20 is used to form a temperature measurement system. The temperature measurement accuracy reaches 0.1 degrees. The temperature range is between -20 degrees and +50 de...[Details]
1. Disadvantages of choosing too high a voltage level
Choosing too high a voltage level will result in too high an investment and a long payback period. As the voltage level increases, the...[Details]
In today's body control module (BCM) designs, savvy engineers are moving away from electromechanical relays whenever possible. Their next step is to eliminate fuses. But is eliminating fuses a nece...[Details]
In 2012, more than half of the cars in the European, Japanese and American car markets will be equipped with color displays, navigation systems, satellite communications and other in-vehicle infota...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guangzho...[Details]
The above is to use MB1404 as a stereo composite signal transmitter. You can use the internal high-frequency amplifier and oscillator or not! According to my experience, I still recommend beginners...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
