Pins designated as "NC" are typically unbonded pins. However some of them are bonded for special testing purposes. Hence if a signal is applied to these pins, care
should be taken that the voltage applied on these pins does not exceed the V
CC
applied to the device. This will ensure proper operation.
Ordering Information
NM
93
C
XX
LZ
E
XXX
Package
N
M8
MT8
None
V
E
Blank
L
LZ
06
C
CS
Interface
93
Letter Description
8-pin DIP
8-pin SO
8-pin TSSOP
0 to 70°C
-40 to +125°C
-40 to +85°C
4.5V to 5.5V
2.7V to 5.5V
2.7V to 5.5V and
<1µA Standby Current
256 bits
CMOS
Data protect and sequential
read
MICROWIRE
Temp. Range
Voltage Operating Range
Density
Fairchild Memory Prefix
2
NM93C06 Rev. E
www.fairchildsemi.com
NM93C06 256-Bit Serial CMOS EEPROM
(MICROWIRE
TM
Synchronous Bus)
Absolute Maximum Ratings
(Note 1)
Ambient Storage Temperature
All Input or Output Voltages
with Respect to Ground
Lead Temperature
(Soldering, 10 sec.)
ESD rating
-65°C to +150°C
+6.5V to -0.3V
Operating Conditions
Ambient Operating Temperature
NM93C06
NM93C06E
NM93C06V
Power Supply (V
CC
)
0°C to +70°C
-40°C to +85°C
-40°C to +125°C
4.5V to 5.5V
+300°C
2000V
DC and AC Electrical Characteristics
V
CC
= 4.5V to 5.5V unless otherwise specified
Symbol
I
CCA
I
CCS
I
IL
I
OL
V
IL
V
IH
V
OL1
V
OH1
V
OL2
V
OH2
f
SK
t
SKH
t
SKL
t
SKS
t
CS
t
CSS
t
DH
t
DIS
t
CSH
t
DIH
t
PD
t
SV
t
DF
t
WP
Parameter
Operating Current
Standby Current
Input Leakage
Output Leakage
Input Low Voltage
Input High Voltage
Output Low Voltage
Output High Voltage
Output Low Voltage
Output High Voltage
SK Clock Frequency
SK High Time
SK Low Time
SK Setup Time
Minimum CS Low Time
CS Setup Time
DO Hold Time
DI Setup Time
CS Hold Time
DI Hold Time
Output Delay
CS to Status Valid
CS to DO in Hi-Z
Write Cycle Time
Conditions
CS = V
IH
, SK=1.0 MHz
CS = V
IL
V
IN
= 0V to V
CC
(Note 2)
Min
Max
1
50
±-1
Units
mA
µA
µA
V
V
V
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
-0.1
2
I
OL
= 2.1 mA
I
OH
= -400
µA
I
OL
= 10
µA
I
OH
= -10
µA
(Note 3)
0°C to +70°C
-40°C to +125°C
250
300
250
50
(Note 4)
250
100
70
100
0
20
2.4
0.8
V
CC
+1
0.4
0.2
V
CC
- 0.2
1
500
500
CS = V
IL
100
10
ns
ns
ns
ms
3
NM93C06 Rev. E
www.fairchildsemi.com
NM93C06 256-Bit Serial CMOS EEPROM
(MICROWIRE
TM
Synchronous Bus)
Absolute Maximum Ratings
(Note 1)
Ambient Storage Temperature
All Input or Output Voltages
with Respect to Ground
Lead Temperature
(Soldering, 10 sec.)
ESD rating
-65°C to +150°C
+6.5V to -0.3V
Operating Conditions
Ambient Operating Temperature
NM93C06L/LZ
NM93C06LE/LZE
NM93C06LV/LZV
Power Supply (V
CC
)
0°C to +70°C
-40°C to +85°C
-40°C to +125°C
2.7V to 5.5V
+300°C
2000V
DC and AC Electrical Characteristics
V
CC
= 2.7V to 5.5V unless otherwise specified
Symbol
I
CCA
I
CCS
Parameter
Operating Current
Standby Current
L
LZ (2.7V to 4.5V)
Input Leakage
Output Leakage
Input Low Voltage
Input High Voltage
Output Low Voltage
Output High Voltage
SK Clock Frequency
SK High Time
SK Low Time
SK Setup Time
Minimum CS Low Time
CS Setup Time
DO Hold Time
DI Setup Time
CS Hold Time
DI Hold Time
Output Delay
CS to Status Valid
CS to DO in Hi-Z
Write Cycle Time
Conditions
CS = V
IH
, SK=1.0 MHz
CS = V
IL
Min
Max
1
10
1
Units
mA
µA
µA
µA
V
V
KHz
µs
µs
µs
µs
µs
ns
µs
ns
µs
I
IL
I
OL
V
IL
V
IH
V
OL
V
OH
f
SK
t
SKH
t
SKL
t
SKS
t
CS
t
CSS
t
DH
t
DIS
t
CSH
t
DIH
t
PD
t
SV
t
DF
t
WP
V
IN
= 0V to V
CC
(Note 2)
-0.1
0.8V
CC
I
OL
= 10µA
I
OH
= -10µA
(Note 3)
0.9V
CC
0
1
1
0.2
(Note 4)
1
0.2
70
0.4
0
0.4
±1
0.15V
CC
V
CC
+1
0.1V
CC
250
2
1
CS = V
IL
0.4
15
µs
µs
µs
ms
Capacitance
T
A
= 25°C, f = 1 MHz (Note 5)
Symbol
C
OUT
C
IN
Note 1:
Stress above those listed under “Absolute Maximum Ratings” may cause permanent damage
to the device. This is a stress rating only and functional operation of the device at these or any other
conditions above those indicated in the operational sections of the specification is not implied. Exposure
to absolute maximum rating conditions for extended periods may affect device reliability.
Note 2:
Typical leakage values are in the 20nA range.
Test
Output Capacitance
Input Capacitance
Typ
Max
5
5
Units
pF
pF
Note 3:
The shortest allowable SK clock period = 1/f
SK
(as shown under the f
SK
parameter). Maximum
SK clock speed (minimum SK period) is determined by the interaction of several AC parameters stated
in the datasheet. Within this SK period, both t
SKH
and t
SKL
limits must be observed. Therefore, it is not
allowable to set 1/f
SK
= t
SKHminimum
+ t
SKLminimum
for shorter SK cycle time operation.
Note 4:
CS (Chip Select) must be brought low (to V
IL
) for an interval of t
CS
in order to reset all internal
device registers (device reset) prior to beginning another opcode cycle. (This is shown in the opcode
diagram on the following page.)
AC Test Conditions
V
CC
Range
(Extended Voltage Levels)
Note 5:
This parameter is periodically sampled and not 100% tested.
V
IL
/V
IH
Input Levels
0.3V/1.8V
0.4V/2.4V
V
IL
/V
IH
Timing Level
1.0V
1.0V/2.0V
V
OL
/V
OH
Timing Level
0.8V/1.5V
0.4V/2.4V
I
OL
/I
OH
±10µA
2.1mA/-0.4mA
2.7V
≤
V
CC
≤
5.5V
(TTL Levels)
4.5V
≤
V
CC
≤
5.5V
Output Load: 1 TTL Gate (C
L
= 100 pF)
4
NM93C06 Rev. E
www.fairchildsemi.com
NM93C06 256-Bit Serial CMOS EEPROM
(MICROWIRE
TM
Synchronous Bus)
Pin Description
Chip Select (CS)
This is an active high input pin to NM93C06 EEPROM (the device)
and is generated by a master that is controlling the device. A high
level on this pin selects the device and a low level deselects the
device. All serial communications with the device is enabled only
when this pin is held high. However this pin cannot be permanently
tied high, as a rising edge on this signal is required to reset the
internal state-machine to accept a new cycle and a falling edge to
initiate an internal programming after a write cycle. All activity on the
SK, DI and DO pins are ignored while CS is held low.
Microwire Interface
A typical communication on the Microwire bus is made through the
CS, SK, DI and DO signals. To facilitate various operations on the
Memory array, a set of 7 instructions are implemented on NM93C06.
The format of each instruction is listed under Table 1.
Instruction
Each of the 7 instructions is explained under individual instruction
descriptions.
Start bit
This is a 1-bit field and is the first bit that is clocked into the device
when a Microwire cycle starts. This bit has to be “1” for a valid cycle
to begin. Any number of preceding “0” can be clocked into the
device before clocking a “1”.
Serial Clock (SK)
This is an input pin to the device and is generated by the master that
is controlling the device. This is a clock signal that synchronizes the
communication between a master and the device. All input informa-
tion (DI) to the device is latched on the rising edge of this clock input,
while output data (DO) from the device is driven from the rising edge
of this clock input. This pin is gated by CS signal.
Opcode
This is a 2-bit field and should immediately follow the start bit.
These two bits (along with 2 MSB of address field) select a
particular instruction to be executed.
Serial Input (DI)
This is an input pin to the device and is generated by the master
that is controlling the device. The master transfers Input informa-
tion (Start bit, Opcode bits, Array addresses and Data) serially via
this pin into the device. This Input information is latched on the
rising edge of the SCK. This pin is gated by CS signal.
Address Field
This is a 6-bit field and should immediately follow the Opcode bits.
In NM93C06, only the LSB bits are used for address decoding
during READ, WRITE and ERASE instructions. During these
three instructions (READ, WRITE and ERASE) the MSB 2 bits are
"don't care" (can be 0 or 1).During all other instructions, the MSB
2 bits are used to decode instruction (along with Opcode bits).
Serial Output (DO)
This is an output pin from the device and is used to transfer Output
data via this pin to the controlling master. Output data is serially
shifted out on this pin from the rising edge of the SCK. This pin is
active only when the device is selected.
Data Field
This is a 16-bit field and should immediately follow the Address
bits. Only the WRITE and WRALL instructions require this field.
D15 (MSB) is clocked first and D0 (LSB) is clocked last (both
[align=center][color=#000][backcolor=rgb(237, 235, 235)][font=微软雅黑][size=17.77777862548828px][b]C Language Embedded System Programming Practice[/b][/size][/font][/backcolor][/color][/align] [align=cen...
Feelings of a DSP Developer I have been engaged in DSP development for several years. I have seen many friends are very interested in DSP development. I will write about my feelings about DSP developm...
My system is 2410 + vxworks. Recently, I have an application problem that I want to solve using bit fields. I have defined the following structure: typedef union { struct { unsigned char Type : 3; uns...
#include msp430g2231.h#include intrinsics.hlong volMeasured[8];unsigned char volMeasuredPosition = 0;long volAverage;// Define an average function long Measured[8]; long Average(long Measured[8]) {uns...
Hello, everyone~ Our weekly intelligence is here again~~ Let's take a look at the latest intelligence~Hot application:1. Free evaluation: AI development board based on Allwinner R329 chip
2. Free tria...
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
From the PIC16F946 datasheet, we know that there are two ways to write values to the LCD for display:
1. Directly write the value to LCDDATA1~LCDDATA23
2. Use disconnect t...[Details]
1. System Structure
This system is a simulation system of indoor air-conditioning temperature/humidity control system. The data acquisition and control center collects temperature/humidity...[Details]
1 Introduction
Intelligent control instruments are one of the most commonly used controllers in industrial control. They are mainly aimed at a specific parameter (such as pressure, tempera...[Details]
1 Introduction
In recent years, there have been many major advances in the production technology and processes of automotive headlights, which have greatly improved the performance of automoti...[Details]
General LED lighting has a current limiting resistor in the driving circuit, and the power consumed by the resistor has nothing to do with the LED light emission. In order to improve efficiency, a...[Details]
Overview
In spectral measurement, photomultiplier tubes (PMT) and charge-coupled devices (CCD) are often used as photoelectric converters. PMT is used in slow-changing, high-precision spectral...[Details]
Different initialization between C8051F and 80C51 series microcontrollers
In the past 30 years, major electronic component manufacturers in the world have launched their own unique single-chip...[Details]
With the widespread application of new services and technologies in the communications industry, the scale and capacity of operators' network construction are getting larger and larger, and the ris...[Details]
Introduction
As the country increases its efforts to control the atmospheric environment, motorcycle emission regulations will become stricter year by year, and motorcycles that do not meet the...[Details]
With the rapid development of wireless
digital communication
, more challenges have been raised for integrated circuit design and testing. In the product design stage, in order to ensure
t...[Details]
The launch of Shenzhou IX is imminent, and Tiangong is welcoming visitors again. Yesterday, Professor Fu Qiang, Vice President of the Institute of Science and Industrial Technology of Harbin Instit...[Details]
Download Centre
京公网安备 11010802033920号
EEWORLD
