ISOCOM
LTD
®
IECQ-CECC
COMPONENT
SPECIFICATION
QC 88000-C002
ISSUE 3
March 2007
Component Specification
For
Ceramic Hermetically Sealed
High Speed Optocouplers
Up-to-date lists and bibliographical references of IEQC-CECC publications may be downloaded from
www.iecq.org
Further copies of this document may be obtained from:
IEC
International Electrotechnical Commission
Commission Electrotechnique Internationale
Box 131, rue de Varembé, CH 1211 Geneva 20, Switzerland
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, Hutton Close, Crowther Industrial Estate, District 3, Washington, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 1 of 12
QC 88000-C001: 2007
ISOCOM
LTD
®
FOREWORD
The IECQ Quality Assessment System for Electronic Components (IECQ) is composed of those member countries of
the International Electrotechnical Commission (IEC) who wish to take part in a harmonized system for electronic
components of assessed quality. IECQ is also known in some European member countries as IECQ-CECC.
The object of the System is to facilitate international trade by the harmonization of the specifications and quality
assessment procedures for electronic components, and by the grant of an internationally recognised Mark, or
Certificate of Conformity. The components produced or services provided under the system are thereby acceptable in
all member countries without further testing.
This Component Specification is based upon the requirements of IEC Publication QC 001002-2, and has been
prepared by:
Isocom Ltd
Hutton Close
Crowther Industrial Estate
Washington
Tyne and Wear
NE38 0AH
Tel:
Fax:
+44 0191 4166 546
+44 0191 4155 055
and published under the authority of:
BSI Product Services
Maylands Avenue
Hemel Hempstead
Hertfordshire
HP2 4SQ
United Kingdom
AMENDMENT RECORD
Issue 1 – Changed Page 4 – Amendments 06/07/09
Issue 2 – Changed Pages 3, 4, 5 & 6 – RoHS Compliant & Amendments – 13/07/10
REQUIREMENTS
The requirements for IECQ-CECC Component Specifications as detailed in QC 001002-2 Amendment 1 clause 5.4 are
satisfied by the following data sheet.
It should note that IECQ-CECC are not responsible for manufacturers declarations made in data sheets which fall
outside the limits of approved detailed in IECQ-CECC certificates.
This Component Specification is intended for use with applicable IECQ-CECC Assessment Specifications. Eg: QC
88000-A0001
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, Hutton Close, Crowther Industrial Estate, District 3, Washington, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 2 of 12
QC 88000-C001: 2007
ISOCOM
LTD
®
Ceramic Hermetically Sealed High Speed Optocouplers
■
■
■
■
■
Features
4N55
CD850
CH380
CS800/801
CSM168-2
■
■
■
■
CSM168-4
CSM1800
CSM1801
MC800
Applications
▪
Military, high reliability system
▪
Medical instruments
▪
Mos, Cmos Applications
▪
Logic Interfacing
▪
Data Transmission
▪
Power Supply
▪
Release to IECQ-CECC
▪
Hermetically Sealed
▪
High Density Packaging
▪
1500V DC withstand Test Voltage
▪
Low Input Requirements
▪
High Current Transfer Ratio
▪
RoHS Compliant
Description
These devices are single, dual and quad, hermetically sealed optocouplers. Each channel is
composed of an infra-red light emitting diode and a photon detector high speed transistor output.
Package styles for these devices include 6 pin, 8 pin, 16 pin flat pack, 6 pin LCC and hybrid 6 pin,
with surface mount, butt cut and gull wing options available. Separate connections for the
photodiodes and output transistor collectors improve the speed up to a hundred times that of a
conventional phototransistor optocoupler by reducing the base-collector capacitance.
The same electrical die, assembly processes and materials are used for each channel of each
device shown below. Therefore absolute maximum ratings, recommended operating conditions,
electrical specifications and performance characteristics are identical for all units. Any exceptions,
due to packaging variations and limitations, are as noted.
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, Hutton Close, Crowther Industrial Estate, District 3, Washington, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 3 of 12
QC 88000-C001: 2007
ISOCOM
LTD
®
Selection Guide Package Styles and Configuration Options
6pin
metal Can
TO-5
6 pin
Hybrid
1
16 pin
Flat Pack
2/4
Package
Lead Style
1
Channels
Common Channel Wiring
Isocom Part Numbers and Options
Commercial
Defense Level
Space Level
Standard Gold Plate Finish
Solder Dipped
Butt Cut/Gold Plate
Gull Wing/Soldered
Crew Cut/Gold Plate
6 Pad LCC
1
8 pin DIP
1/2
16 pin DIP
2
MC800
MC800/L2
MC800/L2S
Gold Plate
CH380
CH380/L2
CH380/L2S
Gold Plate
CSM1800/01
CSM1800/01/L2
CSM1800/01/L2S
Gold Plate
CD850
CS800/801
CD850/L2
CS800/801/L2
CD850/L2S
CS800/801/L2S
Gold Plate
Option 20
Option 10
Option 30
Option 60
4N55
4N55/L2
4N55/L2S
Gold Plate
Option 20
Option 10
Option 30
Option 60
CSM168
CSM168/L2
CSM168/L2S
Gold Plate
Functional Diagrams
MC800
6 pin TO-5
1 Channel
CH380
6 pin Hybrid
1 Channel
CSM1800/01
6 pad LCC
1 Channel
CD850
8 pin DIP
2 Channel
4N55
16 pin DIP
2 Channel
CSM168-2
16 pin Flat Pack
2 Channel
5
3
2
7
1
CS800/801
8 pin DIP
1 Channel
CSM168-4
16 pin Flat Pack
4 Channel
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, Hutton Close, Crowther Industrial Estate, District 3, Washington, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 4 of 12
QC 88000-C001: 2007
ISOCOM
LTD
®
Outline Drawings
16 pin DIP, 4 Channel
16 pin Flat Pack, 2 and 4 Channel
NOTE: DIMENSIONS IN
MILLIMETERS
6 pin TO-5, 1 Channel
0.040(1.02)
6 LEADS
0.0175 (0.445)
45.
0°
0.32 (8.13)
3
2
1
5
6
7
0.037 (0.935)
0.5 (12.70)
0.17 (4.32)
0.022 (5.08)
0.031 (0.787)
For sales enquiries, or further information, please contact our sales office at:
Isocom Ltd, Hutton Close, Crowther Industrial Estate, District 3, Washington, NE38 0AH
Tel: +44 0191 4166 546 Fax: +44 0191 4155 055
©2007 Copyright reserved to Isocom Limited
Page 5 of 12
QC 88000-C001: 2007