..In class today, the teacher wrote a string of code.. ORG 0000H SJMP MAIN ORG 000BH SJMP INT0 MAIN:MOV TMOD,#01H MOV A, #FEH MOV P1,A MOV TH0, #23H MOV TL,#45H [color=#FF0000]SETB TR0[/color] ………… SJ...
[b][size=3]At the same time, you are welcome to add other questions about high-power LED lighting power supply,,,,,, 1. Do LED drivers have to use dedicated LED driver ICs? What are the advantages and...
[size=3]1. To correctly select and use the relay well, it is very important to correctly select the relay. First of all, you must have a thorough understanding of the nature, characteristics and usage...
I usually feed the dog in the interruption, but I found that this has some disadvantages. I would like to ask you where is the best place to feed it so that the system is most stable....
I have configured an IO port as an external interrupt input port, and I need to use this port in the program to obtain the external input level. How can I reconfigure it as a normal IO input? ?...
In the past few days, the news that ZTE was "banned" by the US Department of Commerce has triggered widespread reflection and concern in various domestic industries about the lack of independent co...[Details]
1. Test conditions Hardware: STM32L432KC Main frequency: 80MHz Compiler: IAR 8.20.1 Compiler options: High Speed no size constraints CRC generator polynomial: 0x782f 2. Test Method The softwar...[Details]
As many companies listed with
the concept of
touch screen
begin to "transform and upgrade", the official voice of the TP industry is getting smaller and smaller. At the same time, the list o...[Details]
I slightly changed the lyrics of Yu Quan's song "Running", which seems to be
a reflection of the current state of
Huawei Cloud
. At the annual Huawei Analyst Conference held on April 17,
Zh...[Details]
The application of millimeter wave technology in mobile communications also involves a series of technical problems, including the large propagation loss of millimeter waves and the susceptibility ...[Details]
Different from 51, AVR and other single-chip microcomputers, the clock signal sources of msp430 include LFXT1, XT2 and DCO. 1. LFXT1: It can connect high-speed and low-speed crystal oscillators. In l...[Details]
This paper combines embedded control technology with network control technology to realize the design of temperature control system based on single chip microcomputer through Internet control. Th...[Details]
On May 16, in response to
the public opinion storm caused by
Lenovo's
"
5G
voting" incident,
Lenovo
Holdings Chairman and
Lenovo
Group Founder Liu Chuanzhi, Lenovo Gr...[Details]
1. Heart rate measurement principle 1. What is a heart rate module? The heart rate module is professionally used to monitor the heart rate of the wrist, fingers, forehead, earlobe, chest and other ...[Details]
According to TechRadar, given rumors that
Google
is developing a Pixel Watch
,
the
recently renamed Wear OS
smartwatch
operating system may soon be able to show its full cap...[Details]
As shown in the figure, the author soldered a STM32F207VET6 board using a TQFP (32-100PIN) 0.55MM to direct plug adapter board. The board leads out the SWD debug interface (only PA13 and PA14 are occ...[Details]
This program sets the LED running light and the 0-16 numbers of the 0th position of the digital tube to light up in a cycle. The digital tube program cannot be put into the main function, because the...[Details]
Use common anode digital tube and independent keyboard to connect P1 and P2 ports of single chip to realize answering machine The procedure is as follows: #include reg52.h void delay(unsigned char n)...[Details]
For complex calculations, the speed of the microcontroller is too slow. The best way is to manually calculate all the results in advance, store them in ROM in sequence, and then directly check the re...[Details]
;Question: The 80C51 single-chip microcomputer has a fosc = 6MHz. It is required to use the T1 timer working mode 1 to perform a timing of 40ms. And P1.7 periodically outputs a rectangular wave with ...[Details]