EEWORLDEEWORLDEEWORLD

Part Number

Search

B0202AA-01-2102-B

Description
Fixed Resistor, Thin Film, 0.25W, 21000ohm, 100V, 0.1% +/-Tol, 100ppm/Cel, Surface Mount, 0202, CHIP
File Size381KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

B0202AA-01-2102-B Overview

Fixed Resistor, Thin Film, 0.25W, 21000ohm, 100V, 0.1% +/-Tol, 100ppm/Cel, Surface Mount, 0202, CHIP

B0202AA-01-2102-B Parametric

Parameter NameAttribute value
Objectid1579345424
package instructionCHIP
Reach Compliance Codecompliant
ECCN codeEAR99
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package shapeRECTANGULAR PACKAGE
method of packingTRAY
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance21000 Ω
Resistor typeFIXED RESISTOR
size code0202
surface mountYES
technologyTHIN FILM
Temperature Coefficient100 ppm/°C
Terminal shapeONE SURFACE
Tolerance0.1%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed P x R )
Operating Temperature
Back contact
Noise
R
Top contact
pad chamfered
0.004˝ min bond pad size
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Al / Au optional)
3KÅ Au minimum
10KÅ Al minimum
Silicon Dioxide or
Silicon Nitride
R
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
½R
½R
Backside
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
Passivation
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue January 2009 Sheet 1 of 3
Want to know more about UWB? Just read this article.
The Origin of UWB Technology   Global Positioning Systems (GPS) have been mainstream since the late 1990s and early 2000s. Initially used for outdoor navigation, as navigation technology developed, th...
alan000345 Robotics Development
[TI's first low-power design competition] How to use IAR low-level drivers to operate GPIO
After getting the board, I fumbled around for several days, but still couldn't figure out how to use the underlying driver. Later, I had no choice but to use IAR to develop Wolverine. The first articl...
传媒学子 Microcontroller MCU
Problems with using the stc89c52rc chip
When building a project in Keil, if there is no such chip, should I just select at89c52? What should I do if the SST simulation chip fails to connect to the board? This board can be used when plugged ...
xiongjunfeng Embedded System
Is there a difference between gold plating and silver plating on PCB?
[p=null, 2, left][color=rgb(51, 51, 51)][font="][size=17px]【Jie Duo Bang PCB】Today, the editor will introduce some small knowledge about PCB. For example, whether different colors of PCB affect its pe...
jdbpcb00 PCB Design
【CN0178】50 MHz to 9 GHz RF Power Measurement System Calibrated by Software
CIRCUIT FUNCTION AND BENEFITSThis circuit uses the ADL5902 TruPwrTM detector to measure the rms signal strength of RF signals with crest factors (peak-to-average ratio) varying over a dynamic range of...
EEWORLD社区 ADI Reference Circuit
School forum essence area information ~ electronic circuit design, experiment, test related, practical and easy to understand
[i=s] This post was last edited by paulhyde on 2014-9-15 04:01 [/i] Books on electronic circuit design, experiment and testing found in the electronic circuit section of the school forum are very help...
custom430 Electronics Design Contest

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1273  756  1558  2464  2261  26  16  32  50  46 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号