EEWORLDEEWORLDEEWORLD

Part Number

Search

GUB-GL8ALF-03-2711-B-B

Description
Array/Network Resistor, Isolated, Thin Film, 0.16W, 2710ohm, 0.1% +/-Tol, -25,25ppm/Cel, 4430,
CategoryPassive components    The resistor   
File Size493KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

GUB-GL8ALF-03-2711-B-B Overview

Array/Network Resistor, Isolated, Thin Film, 0.16W, 2710ohm, 0.1% +/-Tol, -25,25ppm/Cel, 4430,

GUB-GL8ALF-03-2711-B-B Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid795609833
package instructionSMT, 4430
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL7.1
structureMolded
JESD-609 codee3
Network TypeIsolated
Number of terminals16
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height2.667 mm
Package length11.176 mm
Package formSMT
Package width7.544 mm
Rated power dissipation(P)0.16 W
resistance2710 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesGUB
size code4430
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Terminal surfaceMatte Tin (Sn)
Tolerance0.1%
TaNFilm
®
Small Outline Surface
Mount Resistor Network
GUB Series
Thin film on ceramic technology
0.220” and 0.300” sizes available
RoHS compliant version available
DESC 87012 and 87013 available
Standard JEDEC packages for automatic placement equipment
Compliant leads to
compensate for
thermal expansion
and contractions.
IRC Advanced Film Division
Ultra precision tantalum
nitride resistance element
on high purity alumina.
Rugged, molded
construction.
IRC’s TaNFilm®, Small Outline Integrated Circuit resistor networks are ideally suited for surface mounting.
The 0.05 inch lead spacing provides higher lead density, increased component count, lower installed resistor
cost, and better reliability. They are ideally suited for the latest surface mount assembly techniques, and each
lead can be 100% visually inspected. The compliant leads relieve thermal expansion and contraction stressed
created by soldering and temperature excursions.
The tantalum nitride film system provides precision tolerance, exceptional TCR tracking, and low noise.
TaNFilm® provides stability, high reliability, and long life characteristics. Testing has demonstrated performance
exceeding MIL-PRF-83401 characteristics H.
Electrical Data
GM Type
Resistance Range (Ω)
GL Type
Absolute Tolerance
Ratio Tolerance To R1
TCR (ppm/°C)
TCR Tracking To R1 (ppm°C)
Operating Temperature Range
Noise
Substrate
Custom circuits and special testing available.
Schem A: 10 to 200K
Schem B: 10 to 1000K
Schem A: 10 to 150K
Schem B: 10 to 75K
Available to ±0.1%
Available to ±0.05%
±25, ±50, ±100
±5
-55°C to +125°C
Less than -25 dB
High purity alumina substrate
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
GUB Series Issue November 2008 Sheet 1 of 3
Can the STM8L151K6, which has only one DAC inside, output two independent voltages at the same time?
There is a project that needs to output two voltages at the same time, one for temperature and one for pressure. The STM8L151K6 used has only one DAC inside. Can it output two independent voltages at ...
dwdsp stm32/stm8
Whistle response circuit (English, but relatively simple)
Beeps when hears your whistleA gadget suitable for key-holders, games etc.Circuit diagram:Parts:R1 22K 1/4W ResistorR2 10K 1/4W ResistorR3 4M7 1/4W ResistorR4,R8 100K 1/4W ResistorsR5 220R 1/4W Resist...
yaoniming3k DIY/Open Source Hardware
Electronic circuit analysis
What is the role of R1, R2 and C4 in this circuit? How are their values selected?...
风雨同舟mm Analog electronics
DIY Solar Electronic Watch + Super Capacitor
Test 5.5V 0.22F supercapacitor voltage is 2.0V when powering the electronic meter. Standby current is about 2uA. Test 1.76V power supply to 1.20 and end standby for 18h. It can meet the standby for a ...
hanskying666 TI Technology Forum
How to assign pins for differential input in quartus?
How to assign pins for differential input in quartus? Please help, I am so confused....
zhenpeng25 FPGA/CPLD
28027 enters illegal interrupt at power-on (ADC+SPI+TIMER)
I don't know why, but every time I power on, I will enter an illegal interrupt when the ADC is turned on (it has nothing to do with SPI and timer). First boot (power on or debug)---->Enter an illegal ...
liangzr Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 528  147  1174  2053  759  11  3  24  42  16 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号