EEWORLDEEWORLDEEWORLD

Part Number

Search

GUB-GM8A-01-3571-C-F

Description
Array/Network Resistor, Isolated, Thin Film, 1.2W, 3570ohm, 0.25% +/-Tol, 100ppm/Cel, Surface Mount, 2244, DIP
CategoryPassive components    The resistor   
File Size493KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

GUB-GM8A-01-3571-C-F Overview

Array/Network Resistor, Isolated, Thin Film, 1.2W, 3570ohm, 0.25% +/-Tol, 100ppm/Cel, Surface Mount, 2244, DIP

GUB-GM8A-01-3571-C-F Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
Objectid1076302403
package instructionSMT, 2244
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL4.8
Other featuresULTRA PRECISION
structureMolded
Component power consumption0.16 W
The first element resistor3570 Ω
JESD-609 codee0
Manufacturer's serial numberGUB
Installation featuresSURFACE MOUNT
Network TypeISOLATED
Number of components1
Number of functions8
Number of terminals16
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height2.286 mm
Package length11.176 mm
Package shapeRECTANGULAR PACKAGE
Package formSMT
Package width5.588 mm
Rated power dissipation(P)1.2 W
Rated temperature70 °C
resistance3570 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesGUB
size code2244
surface mountYES
technologyTHIN FILM
Temperature Coefficient100 ppm/°C
Temperature coefficient tracking5 ppm/°C
Terminal surfaceTin/Lead (Sn/Pb)
Terminal shapeGULL WING
Tolerance0.25%
TaNFilm
®
Small Outline Surface
Mount Resistor Network
GUB Series
Thin film on ceramic technology
0.220” and 0.300” sizes available
RoHS compliant version available
DESC 87012 and 87013 available
Standard JEDEC packages for automatic placement equipment
Compliant leads to
compensate for
thermal expansion
and contractions.
IRC Advanced Film Division
Ultra precision tantalum
nitride resistance element
on high purity alumina.
Rugged, molded
construction.
IRC’s TaNFilm®, Small Outline Integrated Circuit resistor networks are ideally suited for surface mounting.
The 0.05 inch lead spacing provides higher lead density, increased component count, lower installed resistor
cost, and better reliability. They are ideally suited for the latest surface mount assembly techniques, and each
lead can be 100% visually inspected. The compliant leads relieve thermal expansion and contraction stressed
created by soldering and temperature excursions.
The tantalum nitride film system provides precision tolerance, exceptional TCR tracking, and low noise.
TaNFilm® provides stability, high reliability, and long life characteristics. Testing has demonstrated performance
exceeding MIL-PRF-83401 characteristics H.
Electrical Data
GM Type
Resistance Range (Ω)
GL Type
Absolute Tolerance
Ratio Tolerance To R1
TCR (ppm/°C)
TCR Tracking To R1 (ppm°C)
Operating Temperature Range
Noise
Substrate
Custom circuits and special testing available.
Schem A: 10 to 200K
Schem B: 10 to 1000K
Schem A: 10 to 150K
Schem B: 10 to 75K
Available to ±0.1%
Available to ±0.05%
±25, ±50, ±100
±5
-55°C to +125°C
Less than -25 dB
High purity alumina substrate
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
GUB Series Issue November 2008 Sheet 1 of 3
About the peripheral circuit of single chip microcomputer to measure the frequency of alternating current
I want to measure the frequency of the AC power generated by the generator through a single-chip microcomputer. The basic idea is: transformer step-down - diode half-wave rectification - Schmitt trigg...
xhd1099924128 Analog electronics
CN0156 [10 Typical Laboratory Circuit Recommendations] Part 8
[10 Typical Laboratory Circuit Recommendations] 8: The circuit shown in Figure 1 provides a simple method to control the output waveform amplitude of the 75 MHz low power (20 mW) waveform generator (D...
fish001 ADI Reference Circuit
Why does TPS92691 recommend adding resistors and capacitors to the Vin design?
[size=4]The input is 24V DC, but I set the input to 23~25V for safety. The LED I drive is a COB LED. Typical current is 0.17A, power 6.1W. My question now is that in the recommended design of WEBENCH,...
qwqwqw2088 Analogue and Mixed Signal
Drive with your eyes
With the help of the rapid development of sensor technology, the operation mode of today's cars has been significantly different. A German scientist has developed a software called "eyeDriver" that us...
天天谈芯 Creative Market
IAR project configuration project->option restores the default configuration every time it restarts
Hello everyone, every time I open my iar, I have to reconfigure the chip stack and link in the red box. It's so troublesome. Can I save my own configuration?...
coraci RF/Wirelessly
NRF24L01 wireless serial port made by MSP430 uses hardware SPI
[i=s] This post was last edited by lb8820265 on 2014-3-19 16:37 [/i] Not long ago, the forum sent me a msp430launchpad board. After a few days of research, I finally realized the wireless serial port ...
lb8820265 Microcontroller MCU

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 648  429  1629  351  883  14  9  33  8  18 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号