Bulletin No. ENC/LPAX-A
Drawing No. LP0503
Released 11/02
Tel +1 (717) 767-6511
Fax +1 (717) 764-0839
www.redlion-controls.com
LPAX ENCLOSURE, MOUNTING AND LABEL ACCESSORIES
O
O
O
O
ENGINEERING UNIT LABELS
BRACKETS FOR BASE, CEILING, OR WALL MOUNTING
NEMA 4/IP65 ENCLOSURE FOR WASHDOWN ENVIRONMENTS
FRONT PANEL SHROUD FOR ENHANCED VIEWING
LX LABEL ACCESSORY
The LX label accessories allow the 5 digit LPAX display to be customized
with an engineering unit. The label is affixed to the embossed area on the bezel
of the LPAX. The LPAX module is then programmed to turn on its
backlighting, which illuminates the label from behind.
Attach Units
Label to this
embossed
area.
INSTALLATION
Before applying the label, ensure that the
embossed area is clean, dry, and free of dirt.
Remove the backing and center the label in
the embossed area and attach. Take extra care
to seat the edges of the label.
SP3
SP4
ORDERING INFORMATION
MODEL NO.
DESCRIPTION
PART NUMBERS
LX
Custom Units Label for 5 Digit LPAX
Listed Below
K A
LXBLANK0 *
LXK00000
mA
µA
Hz
KWh
kg
kHz
kV
VA
m
3
m
3
kVA
VAC
mV
V
m
3
kg
LXA00000 LXMA0000 LXUA0000 LXHZ0000 LXKHZ000 LXKV0000 LXVA0000 LXKVA000 LXVAC000 LXMV0000 LXV00000
m
cm
ton
h
LXTON/H0
K
3
M
3
W
3
KW
h
kg
ton
gal
kg
LXMOHM10 LXOHM000 LXKOHM00 LXMOHM20 LXW00000 LXKW0000 LXKWH000 LXKG0000 LXTON000 LXGAL000 LXL00000
l
m
l
s
LXML0000 LXKL0000 LXM30000
l
K
l
l
min
mm
ft
3
3
in
3
ft
ft
yd
3
l
m
3
s
min
s
min
h
h
LXKG/H00
LXCM3000 LXMM3000 LXIN3000
LXFT3000 LXYD3000 LXL/H000
3
LXKG/S00 LXKG/MIN LXM3/S00 LXM3/MIN LXM3/H00 LXL/S000
LXL/MIN0
s
ft
min
LXFT3/S0 LXFT3/MN
h
LXFT3/H0 LXBPS000 LXBPM000 LXLPM000 LXGPS000 LXGPM100 LXGPM200 LXGPH000 LXFPS100 LXFPM100 LXFPH000
BPS
BPM
YPH
LPM
gps
GPM
gpm
gph
FPS
FPM
FPH
MPM
fps
kph
u
fpm
RPS
lb
YPS
YPM
IPS
IPM IPH
ppm
mm
s
CPS
cm
s
CPM
cm
min
CPH MPS
m
s
m
min
MPH
t
min
LXFPS200 LXFPM200 LXYPS000 LXYPM000 LXYPH000 LXIPS000
LXIPM000 LXIPH000 LXCPS000 LXCPM000 LXCPH000 LXMPS000 LXMPM000 LXMPH000
rps
lb
rpm
rph
ppb
m
h
x100
LXKPH000 LXRPS100 LXRPS200 LXRPM000 LXRPH000 LXPPB000 LXPPM000 LXMM/S00 LXCM/S00 LXCM/MIN LXM/S000 LXM/MIN0 LXM/H000 LXT/MIN0
min
LXU/MIN0
min
h
T
LXLB/MIN LXLB/H00
LXT10000 LXT20000
t
%RH
pH
deg
G
oz
lb
x10
x1000
LX%RH000 LXPH0000 LXDEG000 LXG00000 LXOZ0000 LXLB0000 LX10X000 LX100X00 LX1000X0
ØA ØB ØC bar
in
Hg
psi
kPa
% in
ft
SEC
VDC
LXS00000 LXSEC000 LXVDC000
yd
mm
cm
°
F
°
C
LXDF0000 ** LXDC0000 **
LXPHA000 LXPHB000 LXPHC000 LXBAR000 LXINHG00 LXPSI000 LXKPA000 LX%00000 LXIN0000 LXFT0000 LXYD0000 LXMM0000 LXCM0000 LXM00000
m
km
LXKM0000 LXN00000 LXHP0000 LXINLB00 LXFTLB00 LXMIN000 LXH00000
* Blank label included with each LPAX
N
hp
in lb
ft lb
min
h S
1
** These labels included with MPAXT units
ENC9-NEMA 4/IP65 LPAX ENCLOSURE
The ENC90000 NEMA 4/IP65 enclosure provides a means of mounting the
LPAX display in dirty or washdown environments. The enclosure comes with
all the gaskets, hardware (except the mounting screws), and brackets required
to base, ceiling, or wall mount the LPAX display. The mounting screws to
attach the brackets to your surface are not provided due to the variety of
installation options available.
DIMENSIONS In inches (mm)
ENCLOSURE ASSEMBLY
1. Before drilling a hole in the enclosure for your wire connector or fitting, ensure
that the location you have chosen allows enough clearance around the MPAX
module.
2. Remove the center section of the gasket provided with the LPAX, and slide it
over the rear of the display and onto the mounting studs.
3. Insert the LPAX into the enclosure as illustrated. Install six #10-32 keps nuts
(supplied with the LPAX) and tighten evenly for uniform gasket compression.
The gasket should be compressed to about 75 to 80% of its original thickness.
Do not overtighten the nuts.
4. Run the wires through the hole that was drilled in the enclosure, and attach them
to the LPAX. Wiring instructions are provided in the appropriate PAX bulletin
shipped with the MPAX Module.
5. Remove the center section of the rear cover gasket. Apply the gasket to the rear
panel of the enclosure by inserting the screws through the panel and into the
holes in the gasket. Position the panel on the enclosure and start all of the
screws. Alternately tighten each screw to ensure uniform gasket compression.
The gasket should be compressed to about 75 to 80% of its original thickness.
6. To securely mount the enclosure, attach the adjustable mounting brackets to the
enclosure using the washers and screws provided.
7. Secure the mounting brackets to the desired mounting location.
Rotate bracket for other
installation choices.
ORDERING INFORMATION
MODEL NO.
DESCRIPTION
PART NUMBERS
ENC9
NEMA 4 Enclosure for LPAX
ENC90000
SHROUD
The optional shroud enhances the readability of the LPAX unit in areas with
high intensity overhead light sources. The shroud can be used in conjunction
with any installation (panel mount, enclosure, or mounting brackets). When
properly installed, the shroud will not affect the integrity of a NEMA 4
installation.
DIMENSIONS In inches (mm)
INSTALLATION
1. Remove the center section of the gasket provided with the LPAX, and slide
it over the rear of the display and onto the mounting studs.
2. Orient the shroud and gasket as shown in the assembly figure, and place it
over the LPAX. The studs of the LPAX should now be protruding through
the rear of the shroud.
3. Follow the remaining installation instructions for panel mounting, bracket
mounting or enclosure mounting as appropriate.
2
ORDERING INFORMATION
MODEL NO.
DESCRIPTION
PART NUMBERS
SHR
Shroud for LPAX
SHRLPAX0
MBLPAX-MOUNTING BRACKETS
The MBLPAX mounting brackets provide an easy way to base, wall, or
ceiling mount the LPAX display. The MBLPAX kit comes with two sets of
brackets, and most of the hardware to mount the LPAX at virtually any angle.
The screws to attach the brackets to your surface are not provided due to the
variety of installation options available.
DIMENSIONS In inches (mm)
ASSEMBLY
ORDERING INFORMATION
MODEL NO.
DESCRIPTION
PART NUMBERS
MB
Mounting Bracket for LPAX
MBLPAX00
Notes:
1. When installing the brackets, the fastener bracket must be installed on the
studs of the LPAX as shown.
2. The mounting bracket may be installed with the flange facing in or out.
3. The rubber washers provided must be installed between the two mounting
brackets during assembly.
4. The screws for fastening the brackets to a surface are not provided in the
MBLPAX kit. The holes are 0.2" in diameter and will accept size #10 screws
and smaller.
3
LIMITED WARRANTY
The Company warrants the products it manufactures against defects in materials and workmanship
for a period limited to one year from the date of shipment, provided the products have been stored,
handled, installed, and used under proper conditions. The Company’s liability under this limited
warranty shall extend only to the repair or replacement of a defective product, at The Company’s
option. The Company disclaims all liability for any affirmation, promise or representation with
respect to the products.
The customer agrees to hold Red Lion Controls harmless from, defend, and indemnify RLC against
damages, claims, and expenses arising out of subsequent sales of RLC products or products
containing components manufactured by RLC and based upon personal injuries, deaths, property
damage, lost profits, and other matters which Buyer, its employees, or sub-contractors are or may be
to any extent liable, including without limitation penalties imposed by the Consumer Product Safety
Act (P.L. 92-573) and liability imposed upon any person pursuant to the Magnuson-Moss Warranty
Act (P.L. 93-637), as now in effect or as amended hereafter.
No warranties expressed or implied are created with respect to The Company’s products except those
expressly contained herein. The Customer acknowledges the disclaimers and limitations contained
herein and relies on no other warranties or affirmations.
Red Lion Controls
20 Willow Springs Circle
York PA 17402
Tel +1 (717) 767-6511
Fax +1 (717) 764-0839
Red Lion Controls BV
Basicweg 11b
NL - 3821 BR Amersfoort
Tel +31 (0) 334 723 225
Fax +31 (0) 334 893 793
Red Lion Controls Asia
31, Kaki Bukit Road 3 #06-04/05 TechLink
Singapore 417818
Tel +65 6744-6613
Fax +65 6743-3360
京公网安备 11010802033920号
EEWORLD
