EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-7LALC2562

Description
Transponder, 10709Mbps(Tx), 10709Mbps(Rx), LC/SPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerLumentum Operations LLC
Download Datasheet Parametric View All

PH1-7LALC2562 Overview

Transponder, 10709Mbps(Tx), 10709Mbps(Rx), LC/SPC Connector,

PH1-7LALC2562 Parametric

Parameter NameAttribute value
Objectid4000956036
Reach Compliance Codecompliant
YTEOL0
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Connection TypeLC/SPC CONNECTOR
Data rate (receive)10709 Mbps
Data rate (send)10709 Mbps
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1528 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-24 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Step 2: Create project files
[i=s]This post was last edited by qi777ji on 2018-9-23 09:52[/i] I finally have some time for myself during this holiday. Since the GD32-colibri-F350RX development board arrived last time, I have used...
qi777ji GD32 MCU
Electric energy measurement solution based on C2000 built-in 12-bit ADC
This application note introduces a solution to implement software energy metering based on the C2000 core and the on-chip 12-bit ADC. C2000 is a 32-bit high-performance real-time microcontroller produ...
灞波儿奔 Microcontroller MCU
How many memory wafers are used in STM32F0 and STM32F1 series?
What memory chip do the STM32F0 and STM32F1 series use? I'm not sure about this, so I'd like to ask someone who knows....
ljl676 stm32/stm8
Connecting GPS with VS2005 WINCE 5.0 platform
I plugged the GPS into the computer with a USB cable and installed activesync. The USB port COM3 is available. In VS2005, I created a WinCE 5.0 device application project. I want to make a simple prog...
274960319 Embedded System
Handwriting drawing chip driver
[i=s] This post was last edited by paulhyde on 2014-9-15 03:30 [/i] Our own measurement chip driver...
95001933 Electronics Design Contest
Atmega128 count value reading problem. Please help me to look at this small program problem.
Hey guys, I use Atmega128. Timer count 1, normal mode, internal crystal, 8 division. Start counting from 0x00. Can we use the following method to record the value in the counter each time we actively ...
dj0930 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2554  1961  2880  2665  687  52  40  58  54  14 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号