CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: T
J
= T
C
= T
A
Electrical Specifications
PARAMETER
AC PERFORMANCE
BW
V
S
+ = +5V, V
S
- = -5V, R
F
= 750Ω for A
V
= 1, R
F
= 375Ω for A
V
= 2, R
L
= 150Ω, T
A
= 25°C unless otherwise
specified.
DESCRIPTION
CONDITIONS
MIN
TYP
MAX
UNIT
-3dB Bandwidth
A
V
= +1
A
V
= +2
300
200
20
MHz
MHz
MHz
V/µs
ns
dB
nV/√Hz
pA/√Hz
pA/√Hz
%
°
BW1
SR
t
S
C
S
e
N
i
N
-
i
N
+
dG
dP
0.1dB Bandwidth
Slew Rate
0.1% Settling Time
Channel Separation
Input Voltage Noise
IN- Input Current Noise
IN+ Input Current Noise
Differential Gain Error (Note 1)
Differential Phase Error (Note 1)
A
V
= +2
A
V
= +2
V
O
= -2.5V to +2.5V, A
V
= +2
V
OUT
= -2.5V to +2.5V, A
V
= -1
f = 5MHz
1900
2200
12
60
4.4
17
50
0.03
0.04
DC PERFORMANCE
V
OS
T
C
V
OS
R
OL
Offset Voltage
Input Offset Voltage Temperature
Coefficient
Transimpedance
Measured from T
MIN
to T
MAX
300
-10
1
5
600
10
mV
µV/°C
kΩ
INPUT CHARACTERISTICS
CMIR
CMRR
+I
IN
-I
IN
R
IN
C
IN
Common Mode Input Range
Common Mode Rejection Ratio
+ Input Current
- Input Current
Input Resistance
Input Capacitance
±3
42
-60
-35
±3.3
50
1
1
45
0.5
80
35
V
dB
µA
µA
kΩ
pF
OUTPUT CHARACTERISTICS
V
O
Output Voltage Swing
R
L
= 150Ω to GND
R
L
= 1kΩ to GND
I
OUT
SUPPLY
I
SON
I
SOFF
Supply Current - Enabled
Supply Current - Disabled
No load, V
IN
= 0V
No load, V
IN
= 0V
3
4
100
5
150
mA
µA
Output Current
R
L
= 10Ω to GND
±3.4
±3.8
95
±3.7
±4.0
120
V
V
mA
2
EL5393A
Electrical Specifications
PARAMETER
PSRR
-IPSR
ENABLE
t
EN
t
DIS
I
IHCE
I
ILCE
V
IHCE
V
ILCE
NOTE:
1. Standard NTSC test, AC signal amplitude = 286mV
I am using the micro SD image file from Terasic's official website. How can I replace the preloader, device tree, etc. generated by my own system with those in the official image?...
30: How are variables stored in temporary local data? The L stack always starts with address "0". In the L stack, the same number of bytes are reserved for each data block as static or local data owne...
The MAC address is not fixed, it is set in the register, so how do I know that my register is unique and does not conflict with others? If a batch of devices is produced, will each program be differen...
[size=4][color=#000000]My major in college is electronic information engineering. I learned a lot of things, so I couldn't learn them all. In addition, the school is very bad. I don't think I can find...
In the previous article in the Industrial DACs series, we looked at how to create and protect three-wire industrial analog outputs. Today, we will move on to two-wire analog outputs. [/color][/align] ...
Project Overview
The micro urine analyzer we designed can detect ten parameters of urine, including white blood cells, nitrite, urobilinogen, protein, pH value, occult blood, specific g...[Details]
Magnetic resonance imaging (MRI) systems can take high-resolution cross-sectional perspective images of the human body, providing very useful information for medical diagnosis. The radio frequency pro...[Details]
Blood pressure is one of the important physiological parameters of the human body. Accurate measurement of it is conducive to early detection and identification of hypertension types, and to the pro...[Details]
With the rapid development of digital technology, various digital display screens have emerged, including LED, LCD, DLP, etc. There are various control systems for various digital large screens, in...[Details]
In the test of the electronic ignition module, in order to simulate the real working condition of the electronic ignition system, the electronic ignition module is often placed in an environment hi...[Details]
Infrared remote control is widely used in household appliances, security, industrial control and people's daily life, especially household appliances and security.
When there are many TVs, VCD...[Details]
0Introduction
In oil drilling, accurate measurement of wellbore posture is the premise of wellbore trajectory control. To this end, this paper fully combines the advantages of single-chip ...[Details]
With the development of supermarket industry and the strengthening of loss prevention awareness, the use of electronic anti-theft equipment (EAS) has become very popular in various parts of the countr...[Details]
As microcontrollers become less expensive and more powerful, electrical designers are finding it more cost-effective to use multiple small controllers in both single-board and multi-board systems. ...[Details]
Many MEMS devices, such as accelerometers and mechanical resonance devices, require a vacuum environment to realize their designed functions. However, verifying whether the package cavity has reach...[Details]
summary
Theoretically explains how to set up a PFC boost regulator using a current sensing transformer with the UCC3817 control IC.
1. Schematic
The schematic diagram is show...[Details]
A well-designed electronic load is not designed just for use in the lab; it should be carefully designed and built to test actual power systems. This is true for military portable systems, such as ...[Details]
1. Introduction
The UCC28051 reference design is a 100W offline AC/DC voltage converter with power factor correction (PFC). This power module design is intended to illustrate how to proper...[Details]
Abstract:
This paper
introduces a data acquisition system based on USB and DSP, which takes advantage of the high-speed transmission characteristics of USB2.0. The overall structure of the ...[Details]
Fetal monitoring is an important means to ensure the safety of perinatal mothers and fetuses and achieve eugenics. Intelligent fetal monitoring is a monitoring method that analyzes the health stat...[Details]