CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: T
J
= T
C
= T
A
Electrical Specifications
PARAMETER
AC PERFORMANCE
BW
V
S
+ = +5V, V
S
- = -5V, R
F
= 750Ω for A
V
= 1, R
F
= 375Ω for A
V
= 2, R
L
= 150Ω, T
A
= 25°C unless otherwise
specified.
DESCRIPTION
CONDITIONS
MIN
TYP
MAX
UNIT
-3dB Bandwidth
A
V
= +1
A
V
= +2
300
200
20
MHz
MHz
MHz
V/µs
ns
dB
nV/√Hz
pA/√Hz
pA/√Hz
%
°
BW1
SR
t
S
C
S
e
N
i
N
-
i
N
+
dG
dP
0.1dB Bandwidth
Slew Rate
0.1% Settling Time
Channel Separation
Input Voltage Noise
IN- Input Current Noise
IN+ Input Current Noise
Differential Gain Error (Note 1)
Differential Phase Error (Note 1)
A
V
= +2
A
V
= +2
V
O
= -2.5V to +2.5V, A
V
= +2
V
OUT
= -2.5V to +2.5V, A
V
= -1
f = 5MHz
1900
2200
12
60
4.4
17
50
0.03
0.04
DC PERFORMANCE
V
OS
T
C
V
OS
R
OL
Offset Voltage
Input Offset Voltage Temperature
Coefficient
Transimpedance
Measured from T
MIN
to T
MAX
300
-10
1
5
600
10
mV
µV/°C
kΩ
INPUT CHARACTERISTICS
CMIR
CMRR
+I
IN
-I
IN
R
IN
C
IN
Common Mode Input Range
Common Mode Rejection Ratio
+ Input Current
- Input Current
Input Resistance
Input Capacitance
±3
42
-60
-35
±3.3
50
1
1
45
0.5
80
35
V
dB
µA
µA
kΩ
pF
OUTPUT CHARACTERISTICS
V
O
Output Voltage Swing
R
L
= 150Ω to GND
R
L
= 1kΩ to GND
I
OUT
SUPPLY
I
SON
I
SOFF
Supply Current - Enabled
Supply Current - Disabled
No load, V
IN
= 0V
No load, V
IN
= 0V
3
4
100
5
150
mA
µA
Output Current
R
L
= 10Ω to GND
±3.4
±3.8
95
±3.7
±4.0
120
V
V
mA
2
EL5393A
Electrical Specifications
PARAMETER
PSRR
-IPSR
ENABLE
t
EN
t
DIS
I
IHCE
I
ILCE
V
IHCE
V
ILCE
NOTE:
1. Standard NTSC test, AC signal amplitude = 286mV
I haven't been to eeworld for a long time. I'm back to the CE camp and making mobile phones. Now I have a question: when using PB to customize the platform, can I choose two BSPs at the same time in t...
[i=s]This post was last edited by meiyao on 2022-10-25 00:03[/i]I believe most people can write this; I will simply describe my method and software here. The video and photos were taken before Nationa...
[align=left]This is a problem with wide-ranging implications. Putting aside other factors, only speaking of PCB design, I have the following experiences for reference: 1. There should be a reasonable ...
[font=Arial][size=2]A very practical hardware development tool! It can calculate the value of resistors in parallel and capacitors in series, the conversion of oscilloscope waveforms and corresponding...
Summary of the four tests of the trial of Easy Power Supply I was quite busy at work some time ago and had no time for the trial. Now that the trial was about to end, I urgently took two days to do th...
Radio Frequency Identification (RFID) technology is a contactless automatic identification technology that uses radio frequency signals to read and write relevant data from target objects to achiev...[Details]
As FPGAs incorporate more and more capabilities, the need for effective debugging tools will become more critical. Careful planning for internal visibility will enable teams to adopt the right debuggi...[Details]
As a single-host multi-slave bus system, the number of slave devices that can be connected to a 1-Wire bus is almost unlimited. In order to avoid logical conflicts, the 1-Wire bus interfaces of all...[Details]
Obtaining real-time and reliable traffic information has always been a bottleneck problem in the development of intelligent transportation systems. The establishment of an intelligent transportatio...[Details]
In electronic measurement technology, frequency measurement is one of the most basic measurements. The commonly used frequency measurement method and period measurement method have great limitation...[Details]
introduction
Taking care of babies is very tiring because they wake up and sleep frequently, and activities such as feeding and changing clothes will take up a lot of adults' time and energy. ...[Details]
Complex circuits and 3D EM simulation tools have reached a point where complex system-level behavior can be simulated before fabrication. Performing EM simulations simultaneously with circuit simul...[Details]
System Introduction
EraSoC-1000 series chips are high-performance SoCs (System on Chips) based on the Loongson core. With their powerful CPU processing capabilities, 64-bit floating-point ...[Details]
Power Integrations (PI) has introduced three charger/adapter reference designs using its new LinkSwitch-II series of AC-DC switching power conversion ICs. The new LinkSwitch-II devices use high-pre...[Details]
1. What is fading?
In terms of scope, fading can be roughly divided into three types: large area fading, small area fading and indoor fading. As shown in Figure 1, large area fading refers t...[Details]
Global IP Solutions (GIPS), a leading provider of high-quality IP multimedia processing solutions, announced that GIPS has enabled Voice over Internet Protocol (VoIP) capabilities for Apple's iPhon...[Details]
Abstract:
An amplifier solution for ceramic speaker systems is presented.
Keywords:
audio; ceramic speaker; amplifier; Class G
Today's portable devices require smaller, thinne...[Details]
The discipline of HHCE (Home Health Care Engineering) is gradually entering people's lives as people pay more attention to health and telemedicine develops. It advocates the concept of "seeking m...[Details]
In the WTK22wtklibdevicesDefaultColorPhoneDefaultColorPhone.properties file in the WTK directory, there is a line touch_screen=false. Change it to true.
MIDP2.0 has three touch screen methods:...[Details]
Nowadays, the phenomenon of using cloned taxis and trucks for operation is becoming more and more serious. The so-called cloned car is one or several unlicensed vehicles that are used to copy anoth...[Details]