EEWORLDEEWORLDEEWORLD

Part Number

Search

3013S1-88082233

Description
Telecom and Datacom Connector, 64 Contact(s), Male, Right Angle, Solder Terminal, Locking Mech, Receptacle
CategoryThe connector    The connector   
File Size106KB,1 Pages
ManufacturerSingatron Enterprises Co
Download Datasheet Parametric View All

3013S1-88082233 Overview

Telecom and Datacom Connector, 64 Contact(s), Male, Right Angle, Solder Terminal, Locking Mech, Receptacle

3013S1-88082233 Parametric

Parameter NameAttribute value
Objectid1157734105
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresW/ 3TABS,TOP&BTM SIDES PNL GND
Board mount optionsSPLIT BOARD LOCK
body width0.563 inch
subject depth0.841 inch
body length4.52 inch
Body/casing typeRECEPTACLE
Connector typeTELECOM AND DATACOM CONNECTOR
Contact to complete cooperationAU ON NI
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
Contact styleTELCOM, MODULAR
Insulator colorBLACK
insulator materialGLASS FILLED POLYESTER
Installation option 1LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of ports8
PCB contact patternSTAGGERED
Plating thickness15u inch
GuidelineUL
Shell surfaceNICKEL
Shell materialCOPPER ALLOY
Terminal length0.128 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts64
Dear big brothers, please help me
module flash_mod(clk,rst,LED_OUT); input clk; inout rst; outputLED_OUT; //----------------------// reg [19:0]cnt; reg led_out; parameter T50ms=20'd999_999; //-------------------------// //------------...
xander_wang FPGA/CPLD
The problem of the servo not rotating when the nodemcu esp8266 development board drives it
[i=s]This post was last edited by xiguabuda on 2022-3-11 22:59[/i]I'm new to this. I'm using a development board and MicroPython to drive the servo, but there's no response. Could you please help me f...
xiguabuda MicroPython Open Source section
Mentor Usage Problems
Dear experts, after installing Mentor DC7.9.2, when Capture Design calls the component library, it cannot be displayed, but the component library can be opened separately. Is there any problem with th...
随风飘啊 PCB Design
Ask about the interrupt response speed
Hello everyone, I have been busy with the WM project recently and have not been online for a long time. I encountered a problem today and I would like to ask you for help. I hope you can give me some ...
huzhiming Embedded System
LM2576 output current problem
Dear experts: I have a question. When I use LM2576S-5.0 as a voltage regulator, why is the output current not 3A, but only 50MA? Please advise! The circuit diagram is attached....
fy_1970 51mcu
A simple example of implementing serial port interruption in STM32F407VG chip based on uTenux real-time operating system
[color=#333333][font=Tahoma, Verdana][size=12px]When learning STM32F407VG, I wrote an example based on uTenux operating system on a simple serial port receive interrupt on the STM32F407VG chip! The ex...
zhangzl Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2781  2626  2506  2762  924  56  53  51  19  37 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号