EEWORLDEEWORLDEEWORLD

Part Number

Search

FP-8987HR-03-2431-FD

Description
Array/Network Resistor, Bussed, Tantalum Nitride/nickel Chrome, 0.025W, 2430ohm, 50V, 1% +/-Tol, -25,25ppm/Cel, 3825,
CategoryPassive components    The resistor   
File Size184KB,4 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Environmental Compliance
Download Datasheet Parametric View All

FP-8987HR-03-2431-FD Overview

Array/Network Resistor, Bussed, Tantalum Nitride/nickel Chrome, 0.025W, 2430ohm, 50V, 1% +/-Tol, -25,25ppm/Cel, 3825,

FP-8987HR-03-2431-FD Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid794071255
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL7.15
structureFlatpack
JESD-609 codee4
Network TypeBussed
Number of terminals14
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
Package height1.905 mm
Package length9.525 mm
Package formSMT
Package width6.35 mm
Rated power dissipation(P)0.025 W
resistance2430 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesFP
size code3825
technologyTANTALUM NITRIDE/NICKEL CHROME
Temperature Coefficient25 ppm/°C
Terminal surfaceGold (Au)
Tolerance1%
Operating Voltage50 V
TaNFilm
®
Precision
Flat Pack Networks
8900 Series
Precision absolute and ratio tolerances available
Qualified to MIL-R-83401 /03, /10 and /15
Qualified to characteristics M, K and H
Custom schematics readily available
Absolute TCR to ±15ppm/°C
TaNFilm
®
resistor networks are designed for use in applications requiring a high degree of reliability, stability, tight
tolerance and TCR tracking, and low noise. The sputtering process for resistor formation has been perfected to allow a
continuous feed production line under high vacuum conditions, thus, insuring uniformity of properties between networks.
Laser trimming makes tight ratios easily achievable. The gold plated copper leads are solid phase welded to a large
area of gold conductor pads on the ceramic substrate assuring the most reliable termination and long term stability.
The Tantalum Nitride resistor material is passivated for environmental protection insuring excellent performance far
superior to military requirements.
Our TaNFilm
®
process enables us to manufacture networks containing different resistance values and still maintain tight
tolerances and tracking characteristics. The nature of our photo-etch process makes it readily adaptable to meet each
individual customer’s needs. Custom circuit designs and special mechanical configurations can be easily achieved
with a modest set up charge while maintaining our high standards of precision and reliability.
Electrical Data
Schematic
Resistance
Range
(Ω)
10 - 49.9
50.0 - 199
Absolute
Tolerance
F, G, J
F, G, J
B, D, F, G, J
B, D, F, G, J
B, D, F, G, J
B, D, F, G, J
B, D, F, G, J
B, D, F, G, J
B, D, F, G, J
Optional
Ratio
Tolerance
F, G
D, F, G
A, B, D, F, G
T, Q, A, B, D, F, G
A, B, D, F, G
B, D, F, G
B, D, F, G
B, D, F, G
B, D, F, G
Absolute TCR
(ppm/°C)
±50; ±100; ±300
±25; ±50; ±100; ±300
±25; ±50; ±100; ±300
±15; ±25; ±50; ±100; ±300
±25; ±50; ±100; ±300
±300; ±100
±300; ±100; ±50
±25; ±50; ±100; ±300
±15; ±25; ±50; ±100; ±300
Tracking
TCR
(ppm/°C)
±20
±10
±5
±5
±5
±50
±20
Element
Power
(mW)
A
200 - 999
1.0K - 100K
101K - 200K
50 - 149
150 - 499
50
B
500 - 999
1.0K - 150K
±5
±5
25
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
A subsidiary of
TT electronics plc
8900 Series Issue September 2009 Sheet 1 of 4
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
The most comprehensive Fudan Micro MCU chip selection information on the entire network
After the heavy snow in Texas, the production capacity of many international manufacturers in China was severely affected, and the shortage of MCU chips was once again aggravated. This is undoubtedly ...
Ruaaa 51mcu
What is the sampling conversion rate of the MSP430 ADC? The manual says the maximum is 200ksps. How is that calculated?
The ADC clock source is set to SMCLK=25MHz, divided by 5, that is, 5MHz, the sampling and holding time is 4 ADC clock cycles, 12-bit accuracy, and the conversion time is 13 cycles, which is more than ...
jianping-sun Microcontroller MCU
Second University for Programmers
Shenzhen Programmer QQ Group Alliance has been established for more than two years and has more than 30 QQ groups with more than 2,000 members. Now it is full of heroes, among which the Shenzhen Progr...
wanswer Embedded System
Great God, look here
I use W5100 as uport and P89V51 as MCU. The ultimate goal is to display the time on LCD. I need help from experts on how to write the program....
刘小凯 51mcu
TI C2000 LaunchPad "draws" intelligent power monitor solution for peripheral home
[size=3][color=#333333]1. Signal acquisition part[/color][/size] [size=3][color=#333333] To do signal acquisition, you must first understand the relevant information of the source signal and the targe...
Aguilera Microcontroller MCU
Does anyone have state machine debugging software?
Which expert has used the state machine debugging software Debussy? Is it easy to use? Do you have any information to contribute?...
eeleader FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2125  2386  2427  2124  560  43  49  12  13  40 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号