To place an order, or for custom orders or specifications not listed, call SSI toll-free at
(888) 477-4320
Limited Warranty
All SSI products are warranted against defective materials and workmanship for a period of one (1) year from the date of delivery to the original
purchaser. Any product that is found to be defective within the one year period will be replaced or repaired at the discretion of SSI. THIS
WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, OF MERCHANTABLITY, FITNESS FOR A PARTICULAR
PURPOSE, PERFORMANCE, OR OTHERWISE. SSI is not an expert in the customer’s technical field and therefore does not warrant the
suitability of its products for the applications selected by the customer. SSI accepts no responsibility for misuse, misapplication or unauthorized
modification of its products. SSI’s obligation under this limited warranty is strictly and exclusively limited to the repair or replacement free of charge
of such products as are to be found to be defective in material or workmanship on the condition that the purchaser gives prompt written notice to
SSI of any claim to breach of warranty within the warranty period, and if requested, returns the defective product(s) to SSI. SSI will not assume any
expenses or liability for repairs made to its products outside of its plant without its prior written consent. SSI reserves the right to satisfy its
warranty obligation in full, with respect to defective products, by the payment to the purchaser of all sums paid by the purchaser to SSI for such
products. IN NO EVENT SHALL SSI BE LIABLE FOR CLAIMS (BASED UPON BREACH OR EXPRESS OR IMPLIED WARRANTY,
NEGLIGENCE OR OTHERWISE) FOR ANY DAMAGES, WHETHER DIRECT, IMMEDIATE, INCIDENTAL, FORSEEABLE, CONSEQUENTIAL,
OR SPECIAL. SSI reserves the right to change its specifications at any time without notice.
[i=s] This post was last edited by sipower on 2019-1-2 21:20 [/i] [align=left][font=宋体]【[/font]NXP Rapid IoT Review】+NO.1 First Hands-On Experience---Small but Complete[/align] [align=left][font=宋体]It...
[size=4]The designed board has reached the SRIO debugging stage. On the board, one V6 and two 6678s are interconnected through 4XSRIO, without a switch in between, and finally the communication betwee...
1 AMBA AHB byte strobe problem
For example, my memory is 32 bits wide. ARM is a byte-aligned operation, and the byte is selected by the lower two bits of the address. That is to say, after receiving t...
Traditional broadcasting systems generally need to be operated manually at a fixed time, and can only realize one-way broadcasting with few functions. Traditional bell ringing equipment has a singl...[Details]
introduction
1 The significance of using RTOS on MSP430
It is understandable that it is meaningless to use RTOS on MSP430. Because the hardware resources of MSP430 are limited (for exampl...[Details]
When the WDP500-2A plane grating monochromator is used to test the emission wavelength of a high-power laser diode at different currents, the matching of the laser diode has the disadvantages of lo...[Details]
1. Circuit composition
The whole circuit consists of two parts:
1. Power saving control circuit
As shown in the figure below. Including delay circuit and drive circuit.
(1) Delay ci...[Details]
1. Introduction
With the growth of parking demand, the scale of parking lots is becoming larger and larger. A lot of research has been done on intelligent parking lots in China, but most of th...[Details]
Analog engineers have traditionally struggled with complexity when designing power supplies that required multiple outputs, dynamic load sharing, hot-swap, or extensive fault-handling capabilities....[Details]
Converged processors meet scalability requirements
In current embedded system design, solutions based on MCU, DSP, FPGA and ASIC account for more than 90% of the market share. These solutions ...[Details]
System design is a complex process. It is not enough to just use ICs. There are many details to consider. This article uses a high-fidelity music playback system as an example to introduce how to s...[Details]
The reason for the light decay of white LEDs: the decline of phosphor performance
So far, the rapid decline of the luminous performance of white light LEDs, especially low-power white light LE...[Details]
The data collector of the automatic weather station is generally designed based on a single-chip microcomputer or a PC/104 bus controller. It has the characteristics of good compatibility with PC, low...[Details]
1 Introduction
Building Automation System (BAS) is a distributed monitoring system (DCS) designed according to distributed information and control theory. It is the result of the mutual de...[Details]
1 Introduction
With the development of control, computer, communication, network technology, etc., a new control technology, namely fieldbus, has emerged in the field of industrial control...[Details]
0 Introduction
With the rise and continuous improvement of the solid-state lighting industry, light-emitting diodes (LEDs) have become an alternative lighting technology and are gr...[Details]
Continuity test
A variety of devices need to be checked for continuity, including cable assemblies, printed circuit boards, and connectors to ensure that these components have the expected contin...[Details]
In the "digital pressure measurement" experimental device of applied physics, the subject technical knowledge of analog circuits, digital circuits, sensors and single-chip microcomputers is used. In o...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
