*2. These sensing distance values apply when a E39-R12 Reflector is used. The MSR function is built-in. The reflected light from the object being measured may affect
the sensing accuracy, so adjust the threshold value before use.
*3. The beam radius is the value for the middle measurement distance and indicates a typical value for the middle sensing distance. The radius is defined by light
intensity of 1/e
2
(13.5%) of the central light intensity.
Light will extend beyond the main beam and may be affected by conditions surrounding the object being measured.
*4. The E3C-LR12 has a fixed beam size (the focal point cannot be changed).
4
E3C-LDA
Amplifier Units
Type
External-input models
Standard models
Pre-wired
Model NPN output
Item
PNP output
Supply voltage
Power consumption
ON/OFF output
E3C-LDA21
E3C-LDA51
Wire-saving
connector
E3C-LDA7
E3C-LDA9
Twin-output models
Standard models
Pre-wired
E3C-LDA11
E3C-LDA41
Wire-saving
connector
E3C-LDA6
E3C-LDA8
Model for Sensor
Communications
Unit
E3C-LDA0
*1
ATC-output models
Standard models
Pre-wired
E3C-LDA11AT
E3C-LDA41AT
Wire-saving
connector
E3C-LDA6AT
E3C-LDA8AT
Analog-output
models
Standard models
Pre-wired
E3C-LDA11AN
E3C-LDA41AN
12 to 24 VDC
±10%,
ripple (p-p) 10% max.
1,080 mW max. (current consumption: 45 mA max. at power supply voltage of 24 VDC)
Load power supply voltage: 26.4 VDC max.; NPN/PNP (depends on model) open collector
Load current: 50 mA max.; residual voltage: 1 V max.
Control output
Voltage output: 1
to 5 VDC
(connected load
10 kΩ min.)
Temperature
characteristics
0.3% F.S./°C
Response time/
Repeat
accuracy
Super-high-
speed mode:
100
μs/4.0%
F.S.
High-speed
mode: 250
μs/
4.0% F.S.
Standard mode:
1 ms/2.0% F.S.
High-resolution
mode: 4 ms/
2.0% F.S.
---
100
μs
for operation and reset
Control output
Analog output
---
Response time
Super-highspeed
80
μs
for operation and reset
mode
*2
High-speed mode
250
μs
for operation and reset
Standard mode
High-resolution
mode
Differential
detection
Timer function
1 ms for operation and reset
4 ms for operation and reset
100
μs
for operation and reset
Switchable between single edge and double edge detection mode.
Single edge: Can be set to 250
μs,
500
μs,
1 ms, 10 ms, or 100 ms.
Double edge: Can be set to 500
μs,
1 ms, 2 ms, 20 ms, or 200 ms.
---
Select from OFF-delay, ON-delay, or one-shot timer.
1 ms to 5 s (1 to 20 ms set in 1-ms increments, 20 to 200 ms set in 10-ms increments, 200 ms to 1 s set in 100-ms increments, and 1 to
5 s set in 1-s increments)
Negative values can be displayed.
Settings can be returned to defaults as required.
Possible for up to 10 Units.
*2
Switchable between up counter
and down counter.
Set count: 0 to 9,999,999
External input setting (Select from
teaching, power tuning, zero reset, light
OFF, or counter reset.)
Output setting (Select from channel 2 output, area
output, or self-diagnosis.)
---
Output setting (Select from channel 2
output, area output, self-diagnosis, or
ATC error output.)
Analog output setting
(Offset voltage can be
adjusted.)
Functions
Zero-reset
Initial reset
Mutual interference
prevention
Counter
I/O settings
Digital display
Display orientation
Ambient temperature
range
*3
Ambient humidity range
Insulation resistance
Dielectric strength
Vibration resistance
*4
Shock resistance
*5
Degree of protection
Connection method
Weight
(packed state)
Materials
Case
Cover
Select from digital incident level + threshold or six other patterns.
Switching between normal/reversed display is possible.
Operating: Groups of 1 to 2 Amplifiers:
−25°C
to 55°C, Groups of 3 to 10 Amplifiers:
−25°C
to 50°C, Groups of 11 to 16 Amplifiers:
−25°C
to 45°C
Storage:
−30°C
to 70°C (with no icing)
Operating and storage: 35% to 85% (with no condensation)
20 MΩ at 500 VDC
1,000 VAC at 50/60 Hz for 1 min.
Destruction: 10 to 55 Hz with a 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Destruction: 500 m/s
2
, 3 times each in X, Y, and Z directions
IP50 (IEC 60529)
Pre-wired or wire-saving connector
*6
Pre-wired Models: Approx. 100 g
Wire-saving Connector Models: Approx. 55 g
Sensor Communications Unit Connector Models: Approx. 55 g
Polybutylene terephthalate (PBT)
Polycarbonate
*1. This model allows you to use an E3X-ECT EtherCAT Sensor Communications Unit or E3X-CRT CompoNet Sensor Communications Unit.
*2. Communications are disabled if super-high-speed mode is selected, and the mutual interference prevention function and the communications function for the
Mobile Console will not function.
*3. The following temperature ranges apply when an E3X-ECT EtherCAT or E3X-CRT CompoNet Sensor Communications Unit is used with the E3C-LDA0: Groups
of 1 or 2 Amplifier Units: 0 to 55°C, Groups of 3 to 10 Amplifier Units: 0 to 50°C, Groups of 11 to 16 Amplifier Units: 0 to 45°C, Groups of 17 to 30 Amplifier Units
(with the E3X-ECT): 0 to 40°C.
*4. The vibration resistance of the E3C-LDA0 is as follows: Destruction: 10 to 150 Hz with a 0.7-mm double amplitude for 80 min each in X, Y, and Z directions.
*5. The shock resistance of the E3C-LDA0 is as follows: Destruction: 150 m/s
2
, 3 times each in X, Y, and Z directions.
*6. A connector for a Sensor Communications Unit is used to connect the E3C-LDA0.
In forum activities, it is inevitable that some netizens will register multiple accounts to participate in the activities in order to get prizes! In the past, this situation was relatively rare, but i...
Is there anyone who makes sensors with a detection distance greater than 5 meters and using 485 protocol? If you have any, please send them to my email: [url=mailto:13380331958@163.com]13380331958@163...
Modern receiving systems must often process veryweak signals, but the noise added by the systemcomponents tends to obscure those very weak signals.Sensitivity, bit error ratio (BER) and noise figure a...
Google's driverless technology is not only an eye-catching technology, but also a subversion of the car usage model.
Those who have watched anti-terrorism films and TV dramas must have been im...[Details]
Overview
As a remote network communication control method with advanced technology, high reliability, complete functions and reasonable cost, CAN-bus has been widely used in various automa...[Details]
1 Introduction
PROFIBUS is an international, open, and manufacturer-independent fieldbus standard. It is widely used in manufacturing automation, process industry automation, and automatio...[Details]
12v Lead Acid batteries used in trucks, cars, RVs and uninterruptible power supplies are usually rated at 12V. This circuit monitors the battery, the charge and discharge curves, gives the cu...[Details]
Capacitance Measurement
Used to verify that capacitors meet the manufacturer's specifications. For quality control, a group of capacitors may be placed in an environmental chamber and the cap...[Details]
Introduction
Automakers are working to reduce vehicle weight to reduce CO2 emissions and improve fuel efficiency. Designers are therefore seeking new technologies and design techniques that can...[Details]
Abstract: With the development and construction of BeiDou II system, China will shift from the situation dominated by GPS to the situation dominated by BeiDou II global navigation system independen...[Details]
0 Introduction
Under normal circumstances, the three-phase power in the power system is symmetrical, and they meet certain amplitude and phase conditions; but when the load changes, the syst...[Details]
introduction
Steam turbines are driven by high-temperature and high-pressure steam generated by boilers to run at high speed. They are key power equipment in thermal power plants. The emergenc...[Details]
The invention of the steam engine ushered in the first conversion of internal energy and mechanical energy for mankind, and the birth of the internal combustion engine at the end of the 19th centur...[Details]
1 What is an LED floodlight?
LED downlights are also called spotlights, projection lamps, and spotlights. They are mainly used for architectural decorative lighting and commercial space lighti...[Details]
As the global LED market demand continues to increase, my country's LED industry will face huge opportunities in the future. However, the core LED technology and patents are basically monopolized b...[Details]
1. Introduction
Stepper motor is a basic component that converts electrical energy into kinetic energy. It has been widely used in a variety of electromechanical equipment, such as various machine...[Details]
With the rapid development of the IT industry, the demand for small DC cooling fans with PWM control (hereinafter referred to as fans) used in electronic products is increasing. This type of DC fan...[Details]
1 Theoretical Analysis
Ultrasonic waves
When propagating in a suspension, the ultrasonic waves that encounter the suspended particles are scattered and attenuated at the interface, an...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
