*2. These sensing distance values apply when a E39-R12 Reflector is used. The MSR function is built-in. The reflected light from the object being measured may affect
the sensing accuracy, so adjust the threshold value before use.
*3. The beam radius is the value for the middle measurement distance and indicates a typical value for the middle sensing distance. The radius is defined by light
intensity of 1/e
2
(13.5%) of the central light intensity.
Light will extend beyond the main beam and may be affected by conditions surrounding the object being measured.
*4. The E3C-LR12 has a fixed beam size (the focal point cannot be changed).
4
E3C-LDA
Amplifier Units
Type
External-input models
Standard models
Pre-wired
Model NPN output
Item
PNP output
Supply voltage
Power consumption
ON/OFF output
E3C-LDA21
E3C-LDA51
Wire-saving
connector
E3C-LDA7
E3C-LDA9
Twin-output models
Standard models
Pre-wired
E3C-LDA11
E3C-LDA41
Wire-saving
connector
E3C-LDA6
E3C-LDA8
Model for Sensor
Communications
Unit
E3C-LDA0
*1
ATC-output models
Standard models
Pre-wired
E3C-LDA11AT
E3C-LDA41AT
Wire-saving
connector
E3C-LDA6AT
E3C-LDA8AT
Analog-output
models
Standard models
Pre-wired
E3C-LDA11AN
E3C-LDA41AN
12 to 24 VDC
±10%,
ripple (p-p) 10% max.
1,080 mW max. (current consumption: 45 mA max. at power supply voltage of 24 VDC)
Load power supply voltage: 26.4 VDC max.; NPN/PNP (depends on model) open collector
Load current: 50 mA max.; residual voltage: 1 V max.
Control output
Voltage output: 1
to 5 VDC
(connected load
10 kΩ min.)
Temperature
characteristics
0.3% F.S./°C
Response time/
Repeat
accuracy
Super-high-
speed mode:
100
μs/4.0%
F.S.
High-speed
mode: 250
μs/
4.0% F.S.
Standard mode:
1 ms/2.0% F.S.
High-resolution
mode: 4 ms/
2.0% F.S.
---
100
μs
for operation and reset
Control output
Analog output
---
Response time
Super-highspeed
80
μs
for operation and reset
mode
*2
High-speed mode
250
μs
for operation and reset
Standard mode
High-resolution
mode
Differential
detection
Timer function
1 ms for operation and reset
4 ms for operation and reset
100
μs
for operation and reset
Switchable between single edge and double edge detection mode.
Single edge: Can be set to 250
μs,
500
μs,
1 ms, 10 ms, or 100 ms.
Double edge: Can be set to 500
μs,
1 ms, 2 ms, 20 ms, or 200 ms.
---
Select from OFF-delay, ON-delay, or one-shot timer.
1 ms to 5 s (1 to 20 ms set in 1-ms increments, 20 to 200 ms set in 10-ms increments, 200 ms to 1 s set in 100-ms increments, and 1 to
5 s set in 1-s increments)
Negative values can be displayed.
Settings can be returned to defaults as required.
Possible for up to 10 Units.
*2
Switchable between up counter
and down counter.
Set count: 0 to 9,999,999
External input setting (Select from
teaching, power tuning, zero reset, light
OFF, or counter reset.)
Output setting (Select from channel 2 output, area
output, or self-diagnosis.)
---
Output setting (Select from channel 2
output, area output, self-diagnosis, or
ATC error output.)
Analog output setting
(Offset voltage can be
adjusted.)
Functions
Zero-reset
Initial reset
Mutual interference
prevention
Counter
I/O settings
Digital display
Display orientation
Ambient temperature
range
*3
Ambient humidity range
Insulation resistance
Dielectric strength
Vibration resistance
*4
Shock resistance
*5
Degree of protection
Connection method
Weight
(packed state)
Materials
Case
Cover
Select from digital incident level + threshold or six other patterns.
Switching between normal/reversed display is possible.
Operating: Groups of 1 to 2 Amplifiers:
−25°C
to 55°C, Groups of 3 to 10 Amplifiers:
−25°C
to 50°C, Groups of 11 to 16 Amplifiers:
−25°C
to 45°C
Storage:
−30°C
to 70°C (with no icing)
Operating and storage: 35% to 85% (with no condensation)
20 MΩ at 500 VDC
1,000 VAC at 50/60 Hz for 1 min.
Destruction: 10 to 55 Hz with a 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Destruction: 500 m/s
2
, 3 times each in X, Y, and Z directions
IP50 (IEC 60529)
Pre-wired or wire-saving connector
*6
Pre-wired Models: Approx. 100 g
Wire-saving Connector Models: Approx. 55 g
Sensor Communications Unit Connector Models: Approx. 55 g
Polybutylene terephthalate (PBT)
Polycarbonate
*1. This model allows you to use an E3X-ECT EtherCAT Sensor Communications Unit or E3X-CRT CompoNet Sensor Communications Unit.
*2. Communications are disabled if super-high-speed mode is selected, and the mutual interference prevention function and the communications function for the
Mobile Console will not function.
*3. The following temperature ranges apply when an E3X-ECT EtherCAT or E3X-CRT CompoNet Sensor Communications Unit is used with the E3C-LDA0: Groups
of 1 or 2 Amplifier Units: 0 to 55°C, Groups of 3 to 10 Amplifier Units: 0 to 50°C, Groups of 11 to 16 Amplifier Units: 0 to 45°C, Groups of 17 to 30 Amplifier Units
(with the E3X-ECT): 0 to 40°C.
*4. The vibration resistance of the E3C-LDA0 is as follows: Destruction: 10 to 150 Hz with a 0.7-mm double amplitude for 80 min each in X, Y, and Z directions.
*5. The shock resistance of the E3C-LDA0 is as follows: Destruction: 150 m/s
2
, 3 times each in X, Y, and Z directions.
*6. A connector for a Sensor Communications Unit is used to connect the E3C-LDA0.
Shenzhen Tongdao Electronic Design Co., Ltd. is a professional LAYOUT company. It is a high-tech enterprise specializing in providing complete electronic product solutions for domestic and foreign cus...
The picture shows a color camera with an electronic magnifier currently used by the company. It was not hit or dropped, but suddenly it became completely dark and no images were displayed. What is the...
I am a beginner. I have seen many functions that use timers for delays, which use the input capture and output capture registers. What is the use of this operation? Please explain it to me. Thank you....
Cooperate with Soochow University to develop various series of boards. If you are interested, please visit our Taobao store: http://store.taobao.com/?shop_id=65678023ad_id=am_id=cm_id=pm_id=...
Develop a USB driver in the microcontroller and support the FAT file system. Create a new file in the USB file system according to the FAT16 rules. First, search for available clusters in the FAT area...
As a wireless broadband metropolitan area network standard, WiMAX technology has greater advantages than previous 3.5GHz MMDS products in terms of non-line-of-sight transmission and spectrum utiliz...[Details]
Google's driverless technology is not only an eye-catching technology, but also a subversion of the car usage model.
Those who have watched anti-terrorism films and TV dramas must have been im...[Details]
Remote keyless entry (RKE) systems have become popular with users, with more than 80% of new cars in North America and more than 70% in Europe equipped with RKE systems. In addition to the obvious ...[Details]
No matter which processor you are learning, the first thing you need to understand is the registers and working mode of the processor.
ARM has 37 registers, including 31 general registers and ...[Details]
1. System Structure
This system is a simulation system of indoor air-conditioning temperature/humidity control system. The data acquisition and control center collects temperature/humidity...[Details]
Overview
As a remote network communication control method with advanced technology, high reliability, complete functions and reasonable cost, CAN-bus has been widely used in various automa...[Details]
Against the backdrop of global warming, energy conservation and emission reduction have become a global hotspot and focus, which has also sounded the clarion call for the take-off of the LED lighti...[Details]
1 Introduction
Washing machines are an indispensable household appliance in the home, and they are developing very fast. Fully automatic washing machines are favored by everyone because of their con...[Details]
Automotive electronics are in a noisy environment
,
so automotive electronics must have excellent electromagnetic compatibility (EMC) performance. The most important part of automotive elec...[Details]
1. Sensor
According to the national standard GB7665-87, a sensor is defined as a device that can sense the specified measured quantity and convert it into a usable output signal according to a...[Details]
In the industrial production process, flow measurement is a widely used measurement physical quantity. In special cases, such as vertical oil wells, when it is not easy to install probes outside the p...[Details]
In recent years, network technology has developed rapidly, especially the rapid development of peer-to-peer networks, which has become one of the focuses of the industry. Related applications based on...[Details]
With the development of my country's economy, environmental pollution caused by energy consumption is becoming more and more serious. Sulfur dioxide and nitrogen oxides emitted from coal-fired flue...[Details]
Motor vehicle garage management control system
1. Usage Requirements
1. There are 70 parking spaces in the garage. Each parking space has a door at the entrance. There should be a control...[Details]
PCB Design
京公网安备 11010802033920号
EEWORLD
