Capacitor Hardware
Type VR Vertical Mounting Clamp
Catalog Part Number
Diameter
of Part to be
Mounted
1" to 1-1/16
1-3/8" to 1-7/16
1-1/2" to 1-9/16
1-3/4" to 1-13/16
2" to 2-1/16
2-1/2" to 2-9/16
3" to 3-1/8
Screw
Nut
Without
Screw & Nut
VR1B
VR3B
VR4B
VR6B
VR8B
VR10B
VR12B
VRSCREW
VRNUT
Unassembled
Screw & Nut
Included
VR1
VR3
VR4
VR6
VR8
VR10
VR12
—
—
Assembled
with
Screw & Nut
VR1A
VR3A
VR4A
VR6A
VR8A
VR10A
VR12A
—
—
1"
1-3/8"
1-1/2"
1-3/4"
2"
2-1/2"
3"
1-7/16"
1-25/32"
1-15/16"
2-1/4"
2-1/2"
3"
3-7/16"
1-7/8*"
2-7/32"
2-11/32"
2-9/16"
2-13/16"
3-5/16"
3-13/16"
A
B
C
Dimensions
9/16" long 6-32 thread NC-2A
Standard hex nut to fit screws
CDE VR mounting clamps may be
used to mount any cylindrical ca-
pacitor with a 1” to 3” diameter
that is to be mounted in a verti-
cal position. Material is 1010 CRS,
commercial grade #4 temper ASI
scale. Parts are finished with .0001
(nominal) zinc chromate plating.
Use for mounting CG types, PSU, SF
and MPF types. Material thickness
is .035”
VR1, 3 & 4
.219”
.375”
C ±0.01”
0.176” x 0.281”
±0.016 (3 places).
VR6, 8,10 & 12
B Mtng ±0.03”
B Mtg
2 Holes
.1561” Dia.
.156”
120 º ±3 º
(3 Places)
.562” .750”
B Mtng ±0.03”
Ø 0.201” ±0.005”
0.18
75 º
A ±0.016”
0.34
8” ±
4” ±
0.01
0.01
6”
6”
Type TH Horizontal Mounting Clip
Dimensions in Inches
Nominal Dia.
Catalog
Part Number
of Part to be
Mounted
A
B
0.375”±0.016”
1.125” ±0.016”
0.035”
0.075” ±0.016”
0.500” ±0.016”
C
0.015
0.030
(*)
(*) 0.340" except TH25 is 0.590".
TH17
TH25
0.625
1.375
Added tolerance to "C" dim.
0.312 0.720
0.312 1.500
Material Thickness
TH17 is 0.016”, TH25
is 0.025”.
Material: 1050 high
carbon steel with
phosphate and oil
finish. TH25 is 1060.
(*) 0.340” execpt TH25 is 0.590”
Retaining tabs
Retaining
must
extendtabs must
extend
lower
lower
than base
base
than
of clip
of clip
B
These clips, though designed for
capacitors, have varied applica-
tions to retain many cylindrical
components. They are used ex-
tensively in the electrical and elec-
tronic industries to hold spindles,
condensers, capacitors, tubes,
rods and conduit. Clips have phos-
phate and oil finish.
C ±0.010"
A
0.135" Dia. Hole
0.135” Dia. Hole
0.594"
ACR15KT Motor Start Resistor Kit
ACR220KT Motor Run Resistor Kit
15K Ohm 2 watt bleeder resistors for AC motor start applica-
tions. Saves relay switch contacts and capacitor, particularly in
capacitor start applications. 1/4” quick connect terminals elimi-
nate need for soldering.
ACR15K:
Pack of 10, 15K Ohm 2 watt bleeder resistor without quick con-
nect terminals.
220K Ohm 1 watt bleeder resistors for AC motor run applica-
tions. Saves relay switch contacts and capacitor, particularly in
capacitor run applications. 1/4” quick connect terminals elimi-
nate need for soldering.
ACR220K:
Pack of 10, 220K Ohm 1 watt bleeder resistor without quick con-
nect terminals.
CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com
Capacitor Hardware
Oval Capacitor Hardware
Mounting Brackets #32107
Case Code
32
37
38
A
C
D
Bracket
32107-1
32107-2
32107-3
Wrap Around Bracket
Case Code
32
37
38
A
C
D
Bracket
30393-5
30393-9
OB3
OB2
OB4
OB3
6-32 Screw
and Nut
Insulating Terminal Boots UL Approved Material
44603 or OC1
44603
32108-2
Motor Start Mounting Hardware
Bracket
End Cap
0.375"
Round Capacitor Hardware
3 Footed Round
Mounting Bracket
Case Code
21
23
24
P
S
T
Bracket
VR6B
VR8B
VR10B
Case
Code
Case Dimensions
(Inches)
D
L
2.750
3.375
4.375
3.375
4.375
3.375
4.375
4.375
1.438
1.438
1.438
1.813
1.813
2.063
2.063
2.563
Down
Wire
Cap
PL3
PL3
PL3
PL6
PL6
PL8
PL8
PL10
Up
Wire
Cap
PLA3
PLA3
PLA3
PLA6
PLA6
PLA8
PLA8
PLA10
Optional
Mounting
Bracket
HB2
HB4
HB8
HB4
HB8
HB4
HB8
HB8
1
2
3
4
5
6
7
8
Order both endcap and bracket for mounting
Wrap Around Bracket
Case Code
Bracket
P
S
T
RB175
RB200
RB250
21
23
24
CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com
Capacitor Hardware
Screw-Terminal, Computer-Grade Capacitor, Mounting Hardware
Figure 1
Figure 2
Figure 3
Figure 4
Clamp Dimensions
Clamp
Number
125562-01
125562-05
125562-02
125562-04
125562-03
125562-06
A
1.375
1.750
2.000
2.500
3.000
3.500
Dimensions in Inches
B
2.125
2.500
2.750
3.250
3.750
4.250
C
2.500
2.875
3.125
3.625
4.125
4.625
D
1.281
1.656
1.906
2.406
2.906
3.481
Bracket Dimensions
Dimensions in Inches
Figure
1
1
2
3
2
3
2
3
4
Bracket
Number
125565-06*
125565-15*
125565-09*
125565-05
125565-14*
125565-10
125565-11*
125565-01
125309-01
1.375
1.750
2.000
2.000
2.500
2.500
3.000
3.000
3.500
1.813
2.188
1.250
2.563
1.500
3.000
1.750
3.500
4.488
30 º
30 º
75 º
30 º
75 º
30 º
75 º
30 º
60 º
2.313
2.625
1.438
2.938
1.688
3.438
1.938
3.938
2.224
.750
.750
1.125
1.125
1.125
1.125
1.125
1.125
.984
.563
.560
.750
.750
.750
.750
.750
.750
–
34.93
44.45
50.80
50.80
63.50
63.50
76.20
76.20
90.00
46.04
55.56
31.75
65.09
38.10
76.20
44.45
88.90
114.00
30º
30º
75º
30º
75º
30º
75º
30º
60º
58.74
66.68
36.51
76.41
42.86
87.31
49.21
100.01
4.70
19.05
19.05
28.58
28.58
28.58
28.58
28.58
28.58
25.00
14.30
14.22
19.05
19.05
19.05
19.05
19.05
19.05
–
A
B
C
D
E
F
A
Dimensions in Millimeters
B
C
D
E
F
Note: All mounting brackets and clamps except Figure 4 are zinc plated. Figure 4 is a black nylon. When mounting capacitors
there is no need to wrap capacitors with protective wrapping before installing mounting clamp.
*Stock bracket
Nylon Nuts for Insulated Stud Mounting
Nylon
Hex Nut
Metal Plate/
Heat Sink
(Reference only)
For Stud Standoff
Nylon Nut
Part Number
M8S17W25
M12S22W30
M12S30W38
(mm)
M8
M12
M12
S (mm)
17
22
30
Nut
W (mm)
25
30
38
Nut
T (mm)
15
18
18
Hex
Head
J (mm)
17
19
19
Diameter
(mm)
17.5
22.5
30.5
Mounting
Min. Hole Max. Chassis Max. Tightening
Thickness
(mm)
5
5
5
Torque
in. lbs.
25
75
75
Diameter Diameter Diameter Elevation
CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com
Capacitor Hardware
Notice and Disclaimer:
All product drawings, descriptions, specifications, statements, information and data
(collectively, the “Information”) in this datasheet or other publication are subject to change. The customer
is responsible for checking, confirming and verifying the extent to which the Information contained in this
datasheet or other publication is applicable to an order at the time the order is placed. All Information given
herein is believed to be accurate and reliable, but it is presented without any guarantee, warranty, representation
or responsibility of any kind, expressed or implied. Statements of suitability for certain applications are based
on the knowledge that the Cornell Dubilier company providing such statements (“Cornell Dubilier”) has
of operating conditions that such Cornell Dubilier company regards as typical for such applications, but
are not intended to constitute any guarantee, warranty or representation regarding any such matter – and
Cornell Dubilier specifically and expressly disclaims any guarantee, warranty or representation concerning
the suitability for a specific customer application, use, storage, transportation, or operating environment.
The Information is intended for use only by customers who have the requisite experience and capability to
determine the correct products for their application. Any technical advice inferred from this Information or
otherwise provided by Cornell Dubilier with reference to the use of any Cornell Dubilier products is given
gratis (unless otherwise specified by Cornell Dubilier), and Cornell Dubilier assumes no obligation or liability
for the advice given or results obtained. Although Cornell Dubilier strives to apply the most stringent quality
and safety standards regarding the design and manufacturing of its products, in light of the current state
of the art, isolated component failures may still occur. Accordingly, customer applications which require a
high degree of reliability or safety should employ suitable designs or other safeguards (such as installation
of protective circuitry or redundancies or other appropriate protective measures) in order to ensure that the
failure of an electrical component does not result in a risk of personal injury or property damage. Although
all product-related warnings, cautions and notes must be observed, the customer should not assume that all
safety measures are indicated in such warnings, cautions and notes, or that other safety measures may not be
required.
CDE Cornell Dubilier • 1605 E. Rodney French Blvd. • New Bedford, MA 02744 • Phone: (508)996-8561 • Fax: (508)996-3830 • www.cde.com
/pla10_pdf/pg_0001.png)
NXP MCU
京公网安备 11010802033920号
EEWORLD/pla10_pdf/1.png)
/pla10_pdf/2.png)
/pla10_pdf/3.png)
/pla10_pdf/4.png)
/pla10_pdf/pg_0002.png)
/pla10_pdf/pg_0003.png)
/pla10_pdf/pg_0004.png)
