RoHS Compliant
Value Added
ATA Disk Module
Ⅲ
Specification for Standard ADM (40P/180D) Low Profile
February 11, 2010
Revision 1.2
Apacer Technology Inc.
4
th
Fl., 75 Hsin Tai Wu Rd., Sec.1, Hsichih, Taipei Hsien 221, Taiwan
Tel: +886-2-2698-2888
Fax: +886-2-2689-2889
www.apacer.com
Value Added
ATA-Disk Module
Ⅲ
AP-FMxxxxFX1XXR-XXXXXJ
Features:
Standard ATA/IDE bus interface
– 512 bytes per sector
– ATA command set compatible
– ATA operating mode supports up to:
PIO Mode-4
Multiword DMA Mode-2
Ultra DMA Mode-4
Connector type
– 40-pin female connector
Low power consumption (typical)
– Supply voltage: 3.3V & 5V
– Active mode: 85mA/95mA (3.3V/5V)
– Sleep mode: 500µA /600µA (3.3V/5V)
Performance
– Sustained read: Up to 35 MB/sec
– Sustained write:
Standard: Up to 15 MB/sec
High Speed: Up to 25 MB/sec
Capacity
– Standard:
128, 256, 512 MB
1, 2, 8 GB
– High Speed:
256, 512 MB
1, 2, 4 GB
NAND flash type: SLC
Temperature ranges
– Operation:
Standard: 0°C to 70°C
ET*.: -40°C to 85°C
– Storage: -40°C to 100°C
Flash management
–
Intelligent endurance design
Advanced wear-leveling algorithms
S.M.A.R.T. technology
Built-in hardware ECC
Enhanced data integrity
–
Intelligent power failure recovery
–
Enhanced security level
Secure protection zone
Quick erase
RoHS compliant
*ET: Extended Temperature
1
© 2010 Apacer Technology Inc.
Rev. 1.2
Value Added
ATA-Disk Module
Ⅲ
AP-FMxxxxFX1XXR-XXXXXJ
Table of Contents
1. GENERAL DESCRIPTION ......................................................................................... 3
1.1 P
ERFORMANCE
-O
PTIMIZED
C
ONTROLLER
........................................................................................... 3
1.1.1 Power Management Unit (PMU)............................................................................................... 3
1.1.2 SRAM Buffer............................................................................................................................ 3
2. FUNCTIONAL BLOCK ............................................................................................... 4
3. PIN ASSIGNMENTS ................................................................................................... 5
4. CAPACITY SPECIFICATION ..................................................................................... 6
4.1 P
ERFORMANCE
S
PECIFICATION
.......................................................................................................... 6
4.2 E
NVIRONMENTAL
S
PECIFICATION
........................................................................................................ 7
5. FLASH MANAGEMENT ............................................................................................. 8
5.1 I
NTELLIGENT
E
NDURANCE
D
ESIGN
...................................................................................................... 8
5.1.1 Advanced wear-leveling algorithms .......................................................................................... 8
5.1.2 S.M.A.R.T. technology ............................................................................................................. 8
5.1.3 Built-in hardware ECC.............................................................................................................. 8
5.1.4 Enhanced data integrity ........................................................................................................... 8
5.2 I
NTELLIGENT
P
OWER
F
AILURE
R
ECOVERY
........................................................................................... 9
5.3 E
NHANCED
S
ECURITY
L
EVEL
............................................................................................................. 9
5.3.1 Secure protection zone ............................................................................................................ 9
5.3.2 Quick erase ............................................................................................................................. 9
6. SOFTWARE INTERFACE ....................................................................................... 10
6.1 C
OMMAND
S
ET
............................................................................................................................... 10
7. ELECTRICAL SPECIFICATION .............................................................................. 12
8. PHYSICAL CHARACTERISTICS ............................................................................ 13
8.1 D
IMENSION
.................................................................................................................................... 13
8.1.1 40 pin/ 180 degree low profile w/o housing pin 20 blocked..................................................... 13
8.1.2 40 pin/ 180 degree low profile w/housing pin 20 blocked........................................................ 14
8.1.3 40 pin/ 180 degree low profile w/o housing pin 20 unblocked................................................. 15
8.1.4 40 pin/ 180 degree low profile w/housing pin 20 unblocked.................................................... 16
9. PRODUCT ORDERING INFORMATION ................................................................. 18
9.1 P
RODUCT
C
ODE
D
ESIGNATIONS
....................................................................................................... 18
9.2 V
ALID
C
OMBINATIONS
..................................................................................................................... 19
9.2.1 Pin 20 Blocked....................................................................................................................... 19
9.2.2 Pin 20 Unblocked................................................................................................................... 21
2
© 2010 Apacer Technology Inc.
Rev. 1.2
Value Added
ATA-Disk Module
Ⅲ
AP-FMxxxxFX1XXR-XXXXXJ
1. General Description
Apacer’s ATA-Disk Module (ADM) is a high-performance, embedded flash drive designed to replace the
conventional IDE hard disk drive. The ADMs can be plugged into a standard IDE connector commonly
found in desktops, IT-STB, industrial PCs and thin client systems. Apacer’s ADM SSD has a built-in
microcontroller with file management firmware that communicates with the ATA standard interfaces. This
means the ADM does not require any additional or proprietary host software such as the Flash File
System (FFS) and the Memory Technology Driver (MTD).
This product is well suited for embedded flash storage applications by offering new and expanded
functionalities as well as more cost-effective designs, better performance and increased reliability.
ADM is designed to work at either 5 or 3.3 Volts, supports the standard ATA/IDE protocol for up to PIO
Mode-4
,
Multiword DMA Mode-2 and Ultra DMA Mode-4 interfaces, and uses the standard ATA driver
complying with all major operating systems such as Microsoft Windows series, Apple Mac OS family, and
UNIX variants.
1.1 Performance-Optimized Controller
The kernel of an ATA-Disk Module is the ATA controller, which translates standard ATA signals into the
data and controls of the flash media. This proprietary ATA controller is specifically designed to attain high
data throughput from the host to the flash.
1.1.1 Power Management Unit (PMU)
The power management unit (PMU) controls the power consumption of the ATA-Disk Module. It reduces
the power consumption of the ATA-Disk Module Controller by putting circuitry not in operation into sleep
mode. The PMU has zero wake-up latency.
1.1.2 SRAM Buffer
The ATA-Disk Module Controller performs as an SRAM buffer to optimize the host’s data transfer to and
from the flash media.
3
© 2010 Apacer Technology Inc.
Rev. 1.2
Value Added
ATA-Disk Module
Ⅲ
AP-FMxxxxFX1XXR-XXXXXJ
2. Functional Block
The ATA-Disk Module (ADM) includes the ATA controller and flash media, as well as the ATA standard
interface. Figure 2-1 shows the functional block diagram.
Flash Array
Flash
Media
HOST
ATA/IDE Bus
ATA
Controller
Flash
Media
Flash
Media
Flash
Media
Figure 2-1:
Functional block diagram
4
© 2010 Apacer Technology Inc.
Rev. 1.2
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
