EEWORLDEEWORLDEEWORLD

Part Number

Search

BU-61585V2-481

Description
Micro Peripheral IC,
CategoryThe embedded processor and controller    Microcontrollers and processors   
File Size365KB,46 Pages
ManufacturerData Device Corporation
Download Datasheet Parametric View All

BU-61585V2-481 Overview

Micro Peripheral IC,

BU-61585V2-481 Parametric

Parameter NameAttribute value
Objectid107320311
Reach Compliance Codecompliant
BU-65170/61580 AND BU-61585
MIL-STD-1553A/B NOTICE 2 RT
AND BC/RT/MT, ADVANCED
COMMUNICATION ENGINE (ACE)
Make sure the next
Card you purchase
has...
®
FEATURES
Fully Integrated MIL-STD-1553
Interface Terminal
Flexible Processor/Memory Interface
Standard 4K x 16 RAM and Optional
12K x 16 or 8K x 17 RAM Available
Optional RAM Parity Generation/
Checking
Automatic BC Retries
Programmable BC Gap Times
BC Frame Auto-Repeat
Flexible RT Data Buffering
Programmable
I
llegalization
DESCRIPTION
DDC's BU-65170, BU-61580 and BU-61585 Bus Controller / Remote
Terminal / Monitor Terminal (BC/RT/MT) Advanced Communication
Engine (ACE) terminals comprise a complete integrated interface
between a host processor and a MIL-STD-1553 A and B or STANAG
3838 bus.
The ACE series is packaged in a 1.9 -square-inch, 70-pin, low-profile,
cofired MultiChip Module (MCM) ceramic package that is well suited
for applications with stringent height requirements.
The BU-61585 ACE integrates dual transceiver, protocol, memory
management, processor interface logic, and a total of 12K words of
RAM in a choice of DIP or flat pack packages. The BU-61585 requires
+5 V power and either -15 V or -12 V power.
The BU-61585 internal RAM can be configured as 12K x 16 or 8K x
17. The 8K x 17 RAM feature provides capability for memory integri-
ty checking by implementing RAM parity generation and verification
on all accesses. To minimize board space and “glue” logic, the ACE
provides ultimate flexibility in interfacing to a host processor and inter-
nal/external RAM.
The advanced functional architecture of the ACE terminals provides
software compatibility to DDC's Advanced Integrated Multiplexer
(AIM) series hybrids, while incorporating a multiplicity of architectural
enhancements. It allows flexible operation while off-loading the host
processor, ensuring data sample consistency, and supports bulk data
transfers.The ACE hybrids may be operated at either 12 or 16 MHz.
Wire bond options allow for programmable RT address (hardwired is
standard) and external transmitter inhibit inputs.
Selective Message Monitor
Simultaneous RT/Monitor Mode
FOR MORE INFORMATION CONTACT:
Data Device Corporation
105 Wilbur Place
Bohemia, New York 11716
631-567-5600 Fax: 631-567-7358
www.ddc-web.com
Technical Support:
1-800-DDC-5757 ext. 7771
All trademarks are the property of their respective owners.
©
1992, 1999 Data Device Corporation
Telephone automatic answering machine circuit diagram
[i=s] This post was last edited by jameswangsynnex on 2015-3-3 19:56 [/i] The circuit of the automatic answering machine is shown in the figure. In the figure, IC2 is a 10-second voice recording and p...
探路者 Mobile and portable
[Synopsys IP Resources] Integrated MAC, PCS, and PHY IP for 400G/800G Ethernet
The bandwidth required to handle more complex data is increasing rapidly, driving the data rates of 800G and 1.6T. There are many factors that contribute to this, such as the increase in the number of...
arui1999 Integrated technical exchanges
How to use the MSP430-FLASH information area
[p=30, 2, left]For the designed products, we often need to save some data, and we often use external serial flash or EEPROM, but sometimes we don't need to store many configuration parameters. At this...
qwerghf Microcontroller MCU
The peak of the switching power supply [attached picture], is this considered high?
I used a switching power supply in my project, and I felt that the burrs were relatively large during use. Some power modules would cause the digital circuit to malfunction (the digital module was nor...
tonytong Power technology
Terminal display
Hello everyone, I would like to ask how to write a driver after writing an application using EVC so that when the application executes a certain step, it can be displayed in the terminal? For example,...
mutalipu Embedded System
I made a circuit board and found that the 3.3V power supply was short-circuited
As the title says, the board was welded by an outside factory. The chip and decoupling capacitor were welded directly. After I got it back, I found that it was short-circuited. Now I can't think of a ...
along153 Test/Measurement

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2588  473  903  2097  790  53  10  19  43  16 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号