EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

380MS137MT1103-6

Description
Connector Accessory
CategoryThe connector    Connector bracket   
File Size393KB,2 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Environmental Compliance
Download Datasheet Parametric View All

380MS137MT1103-6 Overview

Connector Accessory

380MS137MT1103-6 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid2033490833
Reach Compliance Codecompliant
Related Mil-Spec Back CasesMIL-DTL-38999
Rear case cable clipSADDLE
Connector bracket typeCONNECTOR ACCESSORY
DIN complianceNO
IEC complianceNO
MIL complianceYES
MaterialALUMINUM
Military connector accessories nameBACKSHELL
Maximum operating temperature200 °C
Minimum operating temperature-65 °C
Housing size11
msp430x15x 430x16x 430x161x datasheet
msp430x15x 430x16x 430x161x datasheet [[i] This post was last edited by guanglin on 2011-8-2 11:06[/i]]...
guanglin Microcontroller MCU
I am a novice and want to learn how to port ucgui under stm32. How should I start?
I am a novice who wants to learn how to port ucgui under stm32. I have found some information, which are basically ucgui manuals. I don't know how to start. I want to find a video to learn, but I can'...
1989despair Real-time operating system RTOS
Question about MSP430F6736 UCS!
I made a board with 6736. When initializing UCS, the initialization code is as follows: PJDIR |= BIT0 | BIT1 | BIT3; // ACLK, MCLK, SMCLK set out to pins PJSEL |= BIT0 | BIT1 | BIT3; // PJ.0,1,3 for d...
qdavid64 Microcontroller MCU
FPGA SPI Communication Discussion
I am doing a small experiment of FPGA and MCU communication, and I have encountered a problem. Please guide me. The current situation is that the MCU runs first, and then the FPGA starts to run, and t...
cclcxy FPGA/CPLD
C2000 Power-on Boot Mode Analysis
When using C2000, engineers often say that the chip simulation can run, but the stand-alone run cannot run; or when debugging, reset the chip > run, and find that the program cannot run. The main reas...
Jacktang Microcontroller MCU
[Help] Please help me look at this circuit. + voltage has no output, - voltage is normal
After power on, Q9 G pole has 4V voltage (normally there is no voltage), D pole has 0.7V (normally 5V), I don't know where the fault is, please help me analyze it...
卟呤、卟呤 Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2459  1417  1178  1258  2647  50  29  24  26  54 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号