177-740-2-51GS8J5-18BWN datasheet, PDF

Datasheet> All Categories > The connector> Connector bracket> 177-740-2-51GS8J5-18BWN

177-740-2-51GS8J5-18BWN: DescriptionCable Assembly, 28AWG,; CategoryThe connector Connector bracket; File Size858KB，5 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/; Environmental Compliance

Download Datasheet Parametric View All

177-740-2-51GS8J5-18BWN Overview

Cable Assembly, 28AWG,

177-740-2-51GS8J5-18BWN Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	7005060776
Reach Compliance Code	compliant
Country Of Origin	USA
YTEOL	8.7
Other features	STANDARD: MIL-DTL-83513, EMI SHIELDED
Certification	MIL
Conductor surface treatment	SILVER
conductor material	COPPER
ConnectorSide1	MICRO-D FEMALE
ConnectorSide2	MICRO-D FEMALE
Connector bracket type	CABLE ASSEMBLY
structure	STRANDED
Cross-sectional area	0.081 mm2
DIN compliance	NO
IEC compliance	NO
insulator material	CROSSLINKED ETHYLENE-TETRAFLUOROETHYLENE
length	0.467 mm
MIL compliance	YES
Number of conductors	51
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
Rated current	3 A
Rated voltage	150 V
resistance	0.244 Ω
shield	YES
stay	7X36
Wire gauge	28 AWG
Wire and Cable Names	FLEXIBLE CORD AND FIXTURE WIRE

Preview

Download Datasheet

View All

SHIELDING EFFECTIVENESS (Db)

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

SHIELDING EFFECTIVENESS (Db)

Micro-D Harness

EMI Performance with Ground Spring

100

1.00E+03

MWDM Micro-D

Shielded Cable Assembly

Single-Ended or Double-Ended–These

easy-to-order cable

assemblies eliminate the need for expensive assembly labor. 100%

tested and ready for use.

Now With Twisted Pairs–No

need to create a procurement

specification for Micro-D cables with twisted pairs. Glenair 177-740

cables are furnished with a full complement of white/blue twisted

pair wires.

Integral Shield Termination–The

connector shell has a platform

to accept Band-It shield termination bands. The cable shield braid is

attached directly to the connector.

Save Labor, Reduce Weight and Improve EMI Shielding

with Glenair’s Micro-D Shielded Cable Assemblies

Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s

fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-

piece connector shell and secured with a stainless steel

Band-Master™ ATS

clamp. These pre-wired, 100% tested

assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low

shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be

ordered in any length, either single-ended or “back-to-back”.

Ground Spring and EMI Shielding Effectiveness

A gold-plated stainless steel ground spring on the pin connector mating

face offers substantial improvement in EMI protection. The graphs

compare identical connectors tested with and without ground springs.

EMI Performance without Ground Spring

100

1.00E+03

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

frequency (Hz)

High Performance Micro-D Connectors and Cables

U.S. CAGE Code 06324

Printed in U.S.A.

GLENAIR, INC.

•

1211 AIR WAY

•

GLENDALE, CA 91201-2497

•

818-247-6000

•

FAX 818-500-9912

www.glenair.com

B-14

E-Mail: sales@glenair.com

Recommended Resources

AN6657 schematic block diagram and basic application circuit

Fluorescent lamp energy-saving electronic ballast circuit

Stabilized power supply circuit diagram with overvoltage and overcurrent protection and alarm

555 hour meter cost load period signal carrier transmitter circuit

Simple oscillation circuit and application circuit

Short circuit protector with relay

How do I connect P0 to the buzzer?: How to connect? Please give me a picture, thank you....; 孤獨の快樂 51mcu

MSP430G2553 Study Notes 3: (III) Timer_A 1. MSP430g2553 has two 16-bit timers: Timer0_A Timer1_A. Each has three capture/compare registers, with input capture and output compare functions. It can generate timer interrupts and P...; Jacktang Microcontroller MCU

RS485 bus: 1490B is full-duplex, how to convert it to half-duplex? I can only send and receive separately, but cannot achieve its half-duplex working mode. What is the problem? Thank you~~~...; abigale MCU

How do I use the STM8L LCD controller? Does it require the LSE clock?: I don't want to use LSE clock. I saw in the manual that LCD controller can use RTCCLK/2 as clock input; it can also use SYSCLK directly, just turn on the LCD of peripheral clock. But in the program I ...; zxd10000 stm32/stm8

CE memory structure: In a certain virtual address space, the physical address space is repeatedly mapped. Why is it necessary to repeat the mapping? What is the difference between the repeatedly mapped part and the previo...; lisongying658 Embedded System

Does any friend have a QQ group for MSP430 enthusiasts to communicate?: Does anyone have a QQ group for MSP430 enthusiasts? I would like to communicate with everyone through the QQ group, ask questions, learn more, and make progress together!...; shan_99 Microcontroller MCU

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components