EEWORLDEEWORLDEEWORLD

Part Number

Search
 PDF

B41896C7128M003

Description
Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 35V, 20% +Tol, 20% -Tol, 1200uF, Through Hole Mount, RADIAL LEADED, ROHS COMPLIANT
CategoryPassive components    capacitor   
File Size705KB,27 Pages
ManufacturerTDK Corporation
Websitehttp://www.tdk.com
Environmental Compliance
Download Datasheet Parametric View All

B41896C7128M003 Overview

Aluminum Electrolytic Capacitor, Polarized, Aluminum (wet), 35V, 20% +Tol, 20% -Tol, 1200uF, Through Hole Mount, RADIAL LEADED, ROHS COMPLIANT

B41896C7128M003 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid1664421952
package instruction,
Reach Compliance Codecompliant
ECCN codeEAR99
Samacsys DescriptionAluminum electrolytic capacitors, Single-ended Capacitors, 1200μF/35VDC, Up to 135 °C, 16mm dia x 25mm length
Samacsys ManufacturerTDK
Samacsys Modified On2024-01-16 06:27:54
YTEOL7.01
capacitance1200 µF
Capacitor typeALUMINUM ELECTROLYTIC CAPACITOR
diameter16 mm
dielectric materialsALUMINUM (WET)
ESR30 mΩ
leakage current0.42 mA
length25 mm
Installation featuresTHROUGH HOLE MOUNT
negative tolerance20%
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package shapeCYLINDRICAL PACKAGE
Package formRadial
method of packingBLISTER PACK
polarityPOLARIZED
positive tolerance20%
Rated (DC) voltage (URdc)35 V
GuidelineAEC-Q200
ripple current2860 mA
surface mountNO
Delta tangent0.14
Terminal pitch7.5 mm
Terminal shapeWIRE
I would like to recommend a video about TI's amplifier solution.
I have a video about a Texas Instruments (TI) zero-drift, PRIO, programmable gain amplifier with MUX that I’d like to share with you! [flash]http://player.youku.com/player.php/sid/XMjM2NjUyNjIw/v.swf[...
maylove Analogue and Mixed Signal
Please teach me the I2C level conversion circuit, thank you!
I have a chip that can adjust the parameters of the parallel port I2C bus, but the output level of the parallel port is 5v, and the voltage of my chip is 3.3v, so a level conversion circuit is needed ...
糖醋鲤鱼 Embedded System
Op Amps for Everyone, 5th Edition
A must-have for hardware engineers. The book explains operational amplifier design in detail, which is very helpful for solving practical problems.This book is the fifth edition, published in 2017. Th...
arui1999 Download Centre
Why perform near field testing?
[font=Microsoft YaHei] Near field measurements are particularly suitable for engineers who develop components and equipment. They use near field measurements to obtain important data on the causes of ...
bjhyyq Analog electronics
Ultrasonic standing wave axial suspension moving device
[i=s] This post was last edited by Yanyun Shibaqi on 2019-5-24 17:07 [/i] [align=center][font=黑体][size=7]Ultrasonic Standing Wave Axial Suspension Moving Device [/size][/font][/align] [align=left][fon...
燕云十八骑 GD32 MCU
Please recommend me an op amp to replace AD8622
[i=s] This post was last edited by Tianyahaijiaosr on 2017-3-3 09:37 [/i]I imitated this circuit to make a voltage detection system. The function of AD8622 in the figure is to amplify the output signa...
天涯海角sr Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 659  2329  485  285  1010  14  47  10  6  21 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号