REVISION N
DO NOT
SCALE FROM
THIS PRINT
.050
C1
IPD1-XX-S-X-X
((No OF POSITIONS x .100) + .055)
.078±.010
.035±.010
.007
.003
No OF POSITIONS
-02 THRU -25
(PER ROW)
[SEE FIG. 2 FOR -02 POSITION]
OPTION
-R: RETENTION LATCH
(SEE NOTE 16) (SEE SHEET 3)
OPTION
-K: KEYED POLARIZATION
(SEE FIGURE 3, SHEET 2)
ROW SPECIFICATION
-S: SINGLE
NOTES:
.08
C2
.505
- .000
+.006
.220
- .003
SEE NOTE 11
+.005
.050 (TYP)
.0775
(4 PLCS)
C3
((No OF POSITIONS -1) x .100)
.002
.003
(MEASURED AT BASE OF TOWER)
'C'
"A"
C4
.300
.200±.002
IPD1-06-S SHOWN
"A"
.0723
(SEE NOTE 14)
'H'
SEE NOTE 8
"B"
'F'
C5
FIG. 1
'B'
'A'
.0923
(SEE NOTE 14)
1.
C
REPRESENTS A CRITICAL DIMENSION.
2. SAMTEC LOGO SHALL APPEAR AT ONE LOCATION ON SURFACE SHOWN,
APPROXIMATELY .150 x .094 (BOTH SIDES).
3. ALL MULTIPLE CAVITY MOLDS SHALL IDENTIFY EACH CAVITY WITH A LETTER
DESIGNATION LOCATED WHERE SHOWN.
4. ALL IDENTIFICATION MARKS MUST NOT STAND GREATER THAN .002 OFF THE
SURFACE OF THE PART.
5. MOLDED SURFACES SHALL BE CONSISTENT AND SMOOTH. SURFACES TO BE
FREE OF SCATCHES, NICKS, SINK AREAS, VOIDS OR OTHER BLEMISHES.
6. MAX ALLOWABLE BOW: SEE TABLE 1. BOW TO BE MEASURED AT MIDLINE OF PART.
7. PART TO BE SYMMETRIC ABOUT THE CENTERLINE WITHIN +/-.002, UNLESS
OTHERWISE STATED.
8. NUMBER OF POSITIONS (PER ROW) TO BE SHOWN IN THIS AREA EXCLUDING
2, 3 AND 4 POSITIONS. SIZE AND DEPTH SIMILAR TO POSITION 1 INDICATOR.
9. GATE PADS MUST BE RECESSED .005. GATE LOCATION IS AT MOLDERS DISCRETION.
10. END CORES ARE POLARIZED. CONFIRM GEOMETRY RELATIVE TO POSITION 1
INDICATOR & GATE PADS.
11. POSITION 1 INDICATOR TO BE .0005 MAX DEPTH, NOT PRESENT ON 2-4 POSITION
OPTIONS.
12. SPECIFIED POSITIONS TO BE IDENTIFIED WHERE SHOWN (NOTE 4 APPLIES).
13. MOLD DESIGNER HAS DISCRETION OVER RIB LOCATION. STEEL PRINT SETUP
SHEET MUST SHOW RIB CONFIGURATION FOR EACH PART NUMBER.
14. PART MUST DRAFT INWARD FROM BOTTOM TO TOP OF STACK.
15. ALL DIMENSIONS TO BE SYMMETRIC ABOUT CENTERLINE WITHIN .0015
UNLESS OTHERWISE STATED.
16. OPTION NOT FOR SALE. FOR RETENTION LATCH FEATURE , SEE IPD1-XX-S-M PRINT.
'E'
.4800±.0020
.045
PARTING LINE
.255
.100±.005
SEE NOTE 2
SEE NOTE 3
"B"
'D'
+.002
.059
- .001
.112
C6
SECTION "A"-"A"
.020 (2 PLCS)
.082
SECTION "B"-"B"
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
'G'
06
05
04
03
02
01
.XX: .01 [.3]
2
.XXX: .003 [.08]
.XXXX: .0015 [.038]
ANGLES
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: info@SAMTEC.com
code: 55322
DESCRIPTION:
DWG. NO.
.300
MATERIAL:
DO NOT SCALE DRAWING
SHEET SCALE: 2:1
SEE NOTE 12
ZYTEL 101F, COLOR: WHITE
MAX REGRIND: 25%
MAX FLASH ALLOWED: .004
MAX GATE VESTIGE: .002
F:\DWG\MISC\Mktg\IPD1-XX-S-X-X-MKT.SLDDRW
.100 SHROUDED CONTACT BODY
IPD1-XX-S-X-X
04/25/2005
SHEET
1
OF
3
BY:
DEAN P
REVISION N
C7
.0310 SQ (TYP)
.060
.145±.002
.035
C8
C9
.075±.002
.100 REF
.100 (TYP)
'N'
C11
.0187
15°
- 4°
(TYP)
+2°
.0895
- .0000
(TYP)
+.003
+.0030
R.025
.225±.005
.145
.085
.0400 (TYP)
DETAIL 'C'
SCALE 5 : 1
.0800 (TYP)
C10
.0850
- .002
(TYP)
18°
- 2°
(TYP)
+5°
.0200 (TYP)
DETAIL 'A'
SCALE 3 : 1
FIG. 2
DETAIL 'B'
SCALE 5 : 1
.0030
DETAIL 'D'
SCALE 5 : 1
.0110
C12
DETAIL 'G'
SCALE 5 : 1
.0750
- .000
(TYP)
+.003
-02 POSITION
(SAME AS FIG. 1, UNLESS OTHERWISE STATED)
.0690
- .001
.0108
2° REF
30° (TYP)
+.002
34°
.005
.076
.110
- .003
20°
C13
+.000
DETAIL 'N'
SCALE 10 : 1
.006 (TYP)
.0100
.0020
.1300
.015
.200
+.001
.105
- .003
.250
.020 (TYP)
.0250
.0159
30°
.4550
DETAIL 'H'
SCALE 12 : 1
.325
-K: KEYED POLARIZATION
(IPD1-06-S-K SHOWN)
(SAME AS FIG. 1, UNLESS OTHERWISE STATED)
.0100
.030
C14
R.025
(TYP)
FIG. 3
.020
.0300
.0735
DETAIL 'E'
SCALE 8 : 1
"N"
.041
15° (TYP)
MAX FLASH .006 THIS AREA ONLY
.068
DETAIL 'F'
SCALE 4 : 1
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: info@SAMTEC.com
code: 55322
DESCRIPTION:
DWG. NO.
DO NOT SCALE DRAWING
2°
"N"
.100 SHROUDED CONTACT BODY
SHEET SCALE: 2:1
SECTION "N"-"N"
SCALE 4 : 1
IPD1-XX-S-X-X
04/25/2005
SHEET
2
OF
3
F:\DWG\MISC\Mktg\IPD1-XX-S-X-X-MKT.SLDDRW
BY:
DEAN P
REVISION N
( IPD1-06-S-R SHOWN)
(SAME AS FIG.1, UNLESS OTHERWISE STATED)
(SEE NOTE 16)
NOT RELEASED FOR PRODUCTION
FIG. 4
.0015
( IPD1-02-S-R SHOWN)
(SAME AS FIG.2, UNLESS OTHERWISE STATED)
(SEE NOTE 16)
NOT RELEASED FOR PRODUCTION
FIG. 5
DETAIL 'M'
SCALE 6 : 1
"J"
'M'
.0400
C15
.041
- .001
+.000
.250
.126
.1700
.0327
"A"
(SEE TABLE 2)
"J"
.230
C16
R.055
.0170±.0010
SECTION "J"-"J"
SCALE 5 : 1
.355
"K"
'L'
"K"
.1600±.0010
C17
.1700±.0010
C18
.1800±.0010
C19
.0085 X 45°
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
R.005 (TYP)
.035
DETAIL 'L'
SCALE 8 : 1
SECTION "K"-"K"
SCALE 6 : 1
.040
.065
.070
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733
FAX: 812-948-5047
e-Mail: info@SAMTEC.com
code: 55322
DESCRIPTION:
DWG. NO.
DO NOT SCALE DRAWING
SHEET SCALE: 4:1
.100 SHROUDED CONTACT BODY
IPD1-XX-S-X-X
04/25/2005
SHEET
3
OF
3
F:\DWG\MISC\Mktg\IPD1-XX-S-X-X-MKT.SLDDRW
BY:
DEAN P
京公网安备 11010802033920号
EEWORLD
