LT3023EDD#PBF datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Power/power management> The power supply circuit> LT3023EDD#PBF

LT3023EDD#PBF: DescriptionIC reg ldo adj 0.1A 10dfn; CategoryPower/power management The power supply circuit; File Size133KB，4 Pages; ManufacturerLinear ( ADI ); Websitehttp://www.analog.com/cn/index.html; Environmental Compliance

Download Datasheet Parametric View All

LT3023EDD#PBF Overview

IC reg ldo adj 0.1A 10dfn

LT3023EDD#PBF Parametric

Parameter Name	Attribute value
Brand Name	Linear Technology
Is it Rohs certified?	conform to
Maker	Linear ( ADI )
Parts packaging code	DFN
package instruction	HVSON, SOLCC10,.11,20
Contacts	10
Manufacturer packaging code	DD
Reach Compliance Code	compliant
ECCN code	EAR99
Samacsys Description	Linear Technology LT3023EDD#PBF, Dual LDO Voltage Regulator, Adjustable 100mA, 1.22 → 20 V, 10-Pin
Adjustability	ADJUSTABLE
Maximum drop-back voltage 1	0.45 V
Nominal dropback voltage 1	0.3 V
Maximum drop-back voltage 2	0.45 V
JESD-30 code	S-PDSO-N10
JESD-609 code	e3
length	3 mm
Maximum grid regulation rate (%/V)	0.046
Maximum load regulation (%)	2%
Humidity sensitivity level	1
Number of functions	1
Output times	2
Number of terminals	10
Working temperatureTJ-Max	125 °C
Working temperature TJ-Min	-40 °C
Maximum output current 1	0.1 A
Maximum output current 2	0.1 A
Maximum output voltage 1	20 V
Minimum output voltage 1	1.22 V
Maximum output voltage 2	20 V
Minimum output voltage 2	1.22 V
Package body material	PLASTIC/EPOXY
encapsulated code	HVSON
Encapsulate equivalent code	SOLCC10,.11,20
Package shape	SQUARE
Package form	SMALL OUTLINE, HEAT SINK/SLUG, VERY THIN PROFILE
Peak Reflow Temperature (Celsius)	260
Certification status	Not Qualified
Regulator type	ADJUSTABLE POSITIVE MULTIPLE OUTPUT LDO REGULATOR
Maximum seat height	0.8 mm
surface mount	YES
technology	BIPOLAR
Terminal surface	Matte Tin (Sn)
Terminal form	NO LEAD
Terminal pitch	0.5 mm
Terminal location	DUAL
Maximum time at peak reflow temperature	30
width	3 mm
Base Number Matches	1

Preview

Download Datasheet

View All

QUICK START GUIDE FOR DEMONSTRATION CIRCUIT 704

LT3023

DESCRIPTION

Demonstration circuit 704 is a dual output regulator

based on the LT3023 IC, which consists of two iden-

tical LDO linear regulators. The DC704 has an input

voltage range of 2.3V to 20V, and either output is ca-

pable of delivering up to 100mA of output current.

The DC supply current is typically only 20uA (per

channel) at no load. The LT3023 comes in a small

10-pin DFN package, which has an exposed pad on

the bottom-side of the IC for better thermal perform-

ance. DC704 comes installed with ceramic capaci-

tors, because of the LT3023 ability of maintaining

stability with ceramic output capacitors. There are

ceramic bypass capacitors on each output for extra

low noise performance. These features make the

DC704 an ideal circuit for use in battery-powered,

hand-held applications or noise sensitive applica-

tions.

Design files for this circuit are available. Call the

LTC Factory.

DUAL OUTPUT LOW NOISE LDO REGULATORS

QUICK START PROCEDURE

DC704 is easy to set up to evaluate the performance

of the LT3023. Refer to Figure 1 for proper meas-

urement equipment setup and follow the procedure

outlined below for proper operation.

Connect the input power supply to the VIN

and GND terminals. Connect the loads be-

tween the VOUT and GND terminals.

Before proceeding to operation, insert jump-

ers JP3 and JP4 into the OFF positions, jump-

ers JP1 and JP2 into the voltage options of

choice (2.5V, 3.3V, and 5V).

Apply 6.5V at VIN. Measure both VOUT1 and

VOUT2; they should read 0V.

Turn on VOUT1 and VOUT2 by moving jump-

ers JP3 and JP4 from the OFF position to the

ON position. Both output voltages should be

within a tolerance of +/- 2%.

Vary the input voltage from 6.5V to 20V. Both

output voltages should be within +/- 3.3% tol-

erance.

Vary each load current from 0 to 100mA.

Both output voltages should be within a toler-

ance of +/- 4%.

Observe both output voltages AC-coupled;

they should measure noise voltages of less

than 2mVAC each. Refer to Figure 2 for

proper measurement technique.

When finished, move jumpers JP3 and JP4 to

the OFF position and disconnect the power.

Warning - if long leads are used to power the demo

circuit, the input voltage at the part could “ring”,

which could affect the operation of the circuit or even

exceed the maximum voltage rating of the IC. To

eliminate the ringing, insert a small tantalum capaci-

tor (for instance, an AVX part # TAJW106M025R) on

the pads between the input power and return termi-

nals on the bottom of the demo board. The (greater)

ESR of the tantalum will dampen the (possible) ring-

ing voltage due to the use of long input leads. On a

normal, typical PCB, with short traces, the capacitor

is not needed.

Recommended Resources

Homemade simple and practical emergency light circuit diagram

Ultrasonic receiving circuit-receiving circuit composed of discrete components

Automatic LED billboard decorative light circuit at night

Capacitor start, battery powered indicator light circuit

Secondary frequency conversion SSB/CW receiver circuit diagram

LED flasher using programmable unijunction transistor

December 26, year-end review: Lecture on the latest application of embedded technology in the 3G era (Shenzhen): [table][tr][td][float=right][color=#800080][/color][/float][color=#800080][/color][color=#800080][/color][color=#000000][color=#008000][color=#ff6600][font=Verdana][font=Verdana][font=Verdana]Embedded...; bjfarsighttop Embedded System

Basic Concepts of A/D and D/A: [size=4][color=#000000][backcolor=white] A/D is the conversion from analog to digital, relying on the analog to digital converter (Analog to Digital Converter), referred to as ADC. D/A is the conversi...; fish001 Microcontroller MCU

Moderator attention, upgrade the firewall: Today, I did a routine antivirus check and found that the simulation software I downloaded a while ago had a Trojan. I wonder if you have noticed it. Simulation setup72_sp6\Patch.exe Win32.PSWTroj.OnL...; maningmei Talking

Found a new thing in the JTAG of the low-voltage MSP430: In the low-voltage MSP430, there is a module called JTAG Mailbox (JMB) System.The introduction is as follows (I won’t translate the English):The CSYS module provides the capability to exchange user da...; wstt Microcontroller MCU

PADS 2007 Issues: I don't know what I selected. Suddenly, my through-hole pads disappeared, including vias. Then I closed the software and re-applied copper, but the pads were still invisible, but the connection relati...; cat3902982 PCB Design

ARM online upgrade FPGA program method: [i=s] This post was last edited by lzwml on 2014-10-31 13:40[/i] [align=left][color=#000000][font=Times New Roman]ARM[/font] uses [font=Times New Roman]IO[/font] to simulate the [font=Times New Roman]...; lzwml ARM Technology

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components