I use stm32 to control the stepper motor driver to send control signals. I found that the motor generates severe heat and makes a lot of noise during rotation. I would like to ask if there is any way ...
I used to use Protel DXP. I used 99 a little bit, but I felt that it was not as good as DXP (personal feeling), so I kept using DXP. But later I heard many people say that PADS and Cadence are very us...
[i=s] This post was last edited by Beifang on 2019-1-11 20:01 [/i] 1. The debugging process after designing the first example program is also very simple. Continuing the project development of the pre...
1. Lenovo laptop, downloaded the designated wireless adapter Broadcom802.11_Wlan_Vista.exe according to the machine model on the official website 2. The installation was successful, and the Broadcom80...
I'd like to ask what the symbols on the State Grid electricity meter LCD screen mean, but I can't understand what they mean. Please give me some advice. Thank you. As shown in the figure below, what d...
1. Overview
Will passive devices
produce nonlinear intermodulation distortion? The answer is yes! Although there is no systematic theoretical analysis, it has been found in engineerin...[Details]
Do you often have to add brake fluid to your car's brakes? The fact that you need to pump out the brake fluid to make sure there is no gas in the brake fluid line may not be done by the car owner h...[Details]
For a long time, due to the limitation of hardware conditions, the display devices of traditional small handheld devices such as PDA are usually monochrome LCD, and the user interface is very simpl...[Details]
1. Principle of displacement angle sensor
The angle sensor is used to detect angles. It has a hole in its body that fits the LEGO axle. When connected to the RCX, the angle sensor counts once ...[Details]
From the PIC16F946 datasheet, we know that there are two ways to write values to the LCD for display:
1. Directly write the value to LCDDATA1~LCDDATA23
2. Use disconnect t...[Details]
Corelink Semiconductor has launched the CL1100-based 5-7W E27 LED lighting driver system solution DB2. This driver module meets the requirements of small size (L×W×H=5.1cm×2.1cm×1.8cm), low standby...[Details]
Only a small number of LED manufacturers can produce high-quality LEDs. For applications that are only used for simple indication, low-quality LEDs are sufficient. However, high-quality LEDs must...[Details]
1. Introduction
With the increasing popularity of fully automatic washing machines, consumers have higher and higher requirements for their environmenta...[Details]
1 Introduction
Ultrasound refers to elastic vibration with a frequency higher than the audible frequency limit (i.e., in the frequency band above 20 kHz). The propagation process of this vib...[Details]
With the rapid development of wireless
digital communication
, more challenges have been raised for integrated circuit design and testing. In the product design stage, in order to ensure
t...[Details]
The launch of Shenzhou IX is imminent, and Tiangong is welcoming visitors again. Yesterday, Professor Fu Qiang, Vice President of the Institute of Science and Industrial Technology of Harbin Instit...[Details]
Abstract: In order to realize wireless automatic alarm and monitoring of major safety places, based on the basic principle of pyroelectric infrared sensing, a detector for receiving infrared radia...[Details]
1 Overview
In the field of traditional lighting, the concepts and definitions of lamps and lamps are clear. Lamps and lamps have their own applicable product standards, supporting technical st...[Details]
Currently, the commonly used solar cell technologies include monocrystalline silicon solar cells and polycrystalline silicon thin-film solar cells. Production process: Monocrystalline silicon solar...[Details]
1. Fully understand the design requirements of all parties and determine the appropriate solution.
When starting a hardware development project, the original driving force will come from many a...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
