As the title says:Please give me some advice, for STM8 microcontroller, for the OPT option byte, if the initial state is ON, if you need to reprogram the FLASH, you must first set OPT to OFF to remove...
[p=26, null, left][font=宋体][size=3][color=#ff00ff]1. Generate a debuggable program[/color][/size][/font][/p][p=26, null, left][font=宋体][size=3][color=#ff00ff]For example, a source file: main.cpp[/colo...
[i=s]This post was last edited by 285062025 on 2014-10-16 15:42[/i] The program for writing the timing of the control lines SPI_CS SPI_CLK SPI_MOSI connected to ADF4158 for debugging ADF5148 is: void ...
I am currently using FPGA to do network experiments and testing the performance of lwip in raw mode.
S3e 500 board, mb core + xilkernel4.0 + lwip130, has been tuned, ping function, tcp and udp data tr...
There are not three phase-locked loops? The hint is that there are two, and there are only two input clocks, so two phase-locked loops are used, and the other one is not used?...
Photovoltaic inverters are the core equipment of photovoltaic systems. Their main function is to convert the direct current generated by photovoltaic modules into alternating current that meets the...[Details]
The status of interrupts in developing embedded systems is absolutely unquestionable. In the era of C51 microcontrollers, there were only 5 interrupts, including 2 external interrupts, 2 timer/counte...[Details]
1. Purpose In actual product release, if the program stored in the MCU Flash is not protected, some illegal companies may read the program in the Flash through an emulator (J-Link, ST-Link, e...[Details]
0. Preparation First use st-link to connect the stm32 core board and PC for burning St-link Stm32 3.3V 3.3V GND GND SWDIO PART SWCLK DCLK Then connect with USB serial port board to v...[Details]
Overview
Lightning is a strong discharge phenomenon that occurs between thunderstorm clouds and between thunderstorm clouds and the earth due to severe convective weather. Lightning is gen...[Details]
As many companies listed with
the concept of
touch screen
begin to "transform and upgrade", the official voice of the TP industry is getting smaller and smaller. At the same time, the list o...[Details]
Nowadays, everyone is saying that "technology is people-oriented". The essence of the development of technology is to serve the improvement of the quality of life of human beings. Automated driving...[Details]
Autonomous driving
and
5G
are the two hot topics that global companies and media are paying the most attention to, and the combination of the two is the focus of everyone's attention....[Details]
On May 16, in response to
the public opinion storm caused by
Lenovo's
"
5G
voting" incident,
Lenovo
Holdings Chairman and
Lenovo
Group Founder Liu Chuanzhi, Lenovo Gr...[Details]
This is a "cooperation" that is related to the future development of China's semiconductor industry. Let's follow the embedded editor to learn more about the relevant content.
Last week, a...[Details]
1. Function and purpose There are two pins BOOT0 and BOOT1 on each STM32 chip. The level status of these two pins when the chip is reset determines which area the program starts from after th...[Details]
When STM32 uses JTMS (PA13) and JTCK (PA14) as normal I/O ports, add the following code before initialization (the order cannot be reversed): RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE); G...[Details]
The key is the configuration of registers. The T1 timer (16 bits) of CC2530 needs to configure three registers: T1CTL, T1STAT, IRCON Here is just a brief introduction. For more details, please refer ...[Details]
stm32/stm8
京公网安备 11010802033920号
EEWORLD
