EEWORLDEEWORLDEEWORLD

Part Number

Search

B0202GA-01-2213-D

Description
Fixed Resistor, Thin Film, 0.25W, 221000ohm, 100V, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 0202, CHIP
CategoryPassive components    The resistor   
File Size381KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

B0202GA-01-2213-D Overview

Fixed Resistor, Thin Film, 0.25W, 221000ohm, 100V, 0.5% +/-Tol, 100ppm/Cel, Surface Mount, 0202, CHIP

B0202GA-01-2213-D Parametric

Parameter NameAttribute value
Objectid1579383400
package instructionCHIP
Reach Compliance Codecompliant
ECCN codeEAR99
YTEOL0
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package shapeRECTANGULAR PACKAGE
method of packingTRAY
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance221000 Ω
Resistor typeFIXED RESISTOR
size code0202
surface mountYES
technologyTHIN FILM
Temperature Coefficient100 ppm/°C
Terminal shapeONE SURFACE
Tolerance0.5%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed P x R )
Operating Temperature
Back contact
Noise
R
Top contact
pad chamfered
0.004˝ min bond pad size
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Al / Au optional)
3KÅ Au minimum
10KÅ Al minimum
Silicon Dioxide or
Silicon Nitride
R
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
½R
½R
Backside
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
Passivation
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue January 2009 Sheet 1 of 3
Downloads for pressure sensors, flow meters, weighing sensors, ultrasonic sensors, and paperless recorders
Please see the attachment if you need any difference!!...
yzdz888 Sensor
NandFlash first block has a bad sector
When using K9F1G08 to burn the Bootloader, the first byte of the Sector of the first Block written in is different from the one read out, and the data of the following Sectors are also different. I ho...
hongrui Embedded System
Why can MSP430 control the gain of AD7714 by 1x, 4x, and 16x, but not by 2x or 8x? Can someone please help me?
Why is it that the gain of AD7714 controlled by MSP430 can be 1x, 4x, or 16x, but not 2x or 8x? Can someone help me? Thank you very much....
ly971021598 Microcontroller MCU
[AB32VG1 development board review] OLED screen display driver
[i=s]This post was last edited by jinglixixi on 2021-9-3 23:58[/i]OLED screen is a self-luminous display device. It has many types. According to the interface, there are I2C interface and SPI interfac...
jinglixixi Domestic Chip Exchange
Using state machine to eliminate keyboard jitter
Using the state machine to debounce the keyboard is very useful. There is no need to delay and wait for the keyboard to stabilize. When a key is detected to be pressed or popped up, the corresponding ...
tiankai001 MCU
44b0 problem: I wrote the flash, but the board won't start up
Everyone: I have encountered this problem now. I just got the 44b0 board. The flash on it is AMD29LV160. I looked at its datasheet and erased the board according to the general erase procedure. I used...
shenjq Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 980  2246  1138  53  1505  20  46  23  2  31 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号