522-43-599-24-125003 datasheet, PDF

Datasheet> All Categories > The connector> socket> 522-43-599-24-125003

522-43-599-24-125003: DescriptionIC Socket, PGA599, 599 Contact(s), ROHS COMPLIANT; CategoryThe connector socket; File Size165KB，1 Pages; ManufacturerMill-Max; Websitehttps://www.mill-max.com; Environmental Compliance

Download Datasheet Parametric View All

522-43-599-24-125003 Overview

IC Socket, PGA599, 599 Contact(s), ROHS COMPLIANT

522-43-599-24-125003 Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
package instruction	ROHS COMPLIANT
Reach Compliance Code	compliant
ECCN code	EAR99
Contact to complete cooperation	GOLD (30) OVER NICKEL (100)
Contact completed and terminated	Tin (Sn)
Contact material	NOT SPECIFIED
Device slot type	IC SOCKET
Type of equipment used	PGA599
Shell material	POLYCYCLOHEXYDIMETHYLENE TEREPHTHALATE-POLYESTER
JESD-609 code	e3
Number of contacts	599
Base Number Matches	1

Preview

Download Datasheet

View All

PIN GRID ARRAY SOCKETS

Wrapost

Series 522, 523

•

Series 522 & 523 PGA

sockets are available in 2 and 3

level wrapost lengths.

•

Choice of three low force clips to

cover all applications.

•

Hi-Temp PCT polyester insulator

material suitable for all forms of

soldering.

Ordering Information

2 LEVEL WRAPOST

SERIES 522

1. Select 2 or 3 Level Wrapost pin at left to determine series number.

2. Specify 2-digit plating code from chart at bottom of page.

3. Locate footprint pattern from pages 107 to 111, the middle 8 digits of

the part number will be located under the pattern.

4. Determine the last 2 digits of part number from the Contact Chart below.

Series

Plating

Code

Window

Clip Type

5 2

No. of pins

Grid size

Pattern #

Determined from footprint pattern pages 107 to 111

3 LEVEL WRAPOST

SERIES 523

EXAMPLE OF COMPLETE PART NUMBER:

523-13-068-11-061001

This is a 68 pin (11x11 grid) insulator with a .6” square

window and fitted with 3 level wraposts. Pin sleeve is

plated 10μ” gold, inner contacts are Mill-Max #32 and

are plated 30μ” gold.

Clip

Type

Contact (Clip) Chart

Mill-Max #32 clip, standard low force, recommended for devices

with less than 150 pins. See page 208 for details.

Mill-Max #35 clip, ultra low force, recommended for devices with

more than 150 pins, but less than 250 pins. See page209 for details.

Mill-Max #43 clip, “ultra lite”, recommended for devices with

more than 250 pins. See page 209 for details.

10µ” Au

30µ” Au

SPECIFY PLATING CODE XX=

10µ” Au

30µ” Au

200µ”Sn/Pb

10µ” Au

Sleeve (Pin)

Contact (Clip)

200µ” Sn/Pb

200µ”Sn/Pb 200µ”Sn

200µ”Sn

30µ” Au

200µ”Sn

w w w. m i l l - m a x . c o m

516-922-6000

Recommended Resources

Capacitive sensor system circuit

Water full alarm circuit three

OCL power amplifier with integrated op amp driver

Circuit for driving DC motor forward/reverse using AC heater

Overvoltage protection circuit example circuit diagram a

Schematic block diagram of TX-KBl02

CPLD generates pulse width adjustable PWM signal: Dear experts, I used Altera's EPM240 to make a PWM output. The project requirements are: the pulse width is adjustable from 10ns to 100ns, the amplitude is 3.3, the frequency is 100k, and the rise tim...; dongxu_LCC FPGA/CPLD

A mistake about Weifu: ORG 0000H SJMP MAIN MAIN:MOV P1,#FFH .5 ACALL DE05 CLR P1.5 CPL P3.0 REL1:JB P1.2,REL2 SETB P1.6 ACALL DE05 CLR P1.6 CPL P3.0 REL2:JB P1.3,REL3 SETB P1.7 ACALL DE05 CLR P1.7 CPL P3.0 REL3:MOV A,P1 ORL...; microchenhard Embedded System

The built-in sweep generation capability of the Series 2600A SourceMeter instrument enables faster throughput and precise timing control: The setup run time is to configure the SMU source and measure [1] parameters before performing the sweep . Therefore, the setup interval only needs to be run once. From there, the sweep can be run as ...; Jack_ma Test/Measurement

Agilent E3632A Repair: When the power is on and the load is not applied, I adjusted the voltage knob. When it reached 8V, I found that there was a burning smell and the area marked CR37 was black. Can someone tell me what i...; 寒夜星辰 Power technology

Question + Why won't the program reset when it's running?: When the program does not enter LPM3 mode, when monitoring through the serial port.....; accboy TI Technology Forum

The core board cannot start UBOOT from NOR: The core board I just bought cannot boot from NOR. UBOOT has been burned in NOR. It can be normally booted from NOR on the development board. My board and the development board have the same reset cir...; zeng2730 Embedded System

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components