EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-SS2LC2682

Description
Transponder, LC/SPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerJDS Uniphase Corporation ( VIAVI )
Websitehttp://www.jdsu.com/index.html
Download Datasheet Parametric View All

PH1-SS2LC2682 Overview

Transponder, LC/SPC Connector,

PH1-SS2LC2682 Parametric

Parameter NameAttribute value
Objectid1871081685
Reach Compliance Codeunknown
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Communication standardsGR-253, OC-192, SONET
Connection TypeLC/SPC CONNECTOR
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1530 nm
Nominal optical power output0.562 mW
minimum return loss-27 dB
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
Application sample + my application experience, summarized
The multi-parameter debugging signal source DIY activity requires eight samples in total, but ADI only allows four samples to be applied for each time. I was free at home today, so I applied for four ...
exiao ADI Reference Circuit
CPLD has no reset signal input, how to generate a reset signal using code
Is it possible to use code to generate a reset signal that lasts for a certain period of time when the CPLD is powered on?...
hzfywht FPGA/CPLD
iar ewarm 6.10.1 cracked version
iar ewarm 6.10.1 cracked version is composed of iar ewarm 6.10.1 official original file plus registration machine. After installing the original file, run the registration machine to register...
aa0613 Microcontroller MCU
【Cyclone V Evaluation Board】 -- How to update the board
The Cyclone V evaluation board has update routines in the firmware, including the Nios II embedded processor, Ethernet MAC , and HTML web service. When SW3.3 is turned to off (1) , the update process ...
dontium FPGA/CPLD
Newbie asks for advice on the timing problem of msp430 timer
#includevoid main(void) int i=0; WDTCTL =WDTPW+WDTHOLD; P2DIR = 0X01;P2OUT = 0X01; P3DIR = 0X01;P3OUT = 0X01; P1DIR = 0X01;P1OUT = 0X01; //Set P1 port direction to outputwhile(i10) { TA0CCR0=32768; //...
...1234 MCU
Question: Does msp430 have this?
Does TI have a library for this MCU like ST? If not, is there a pre-written one online? It would be difficult to write it yourself, right?...
小营七郎 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1518  1458  1481  1689  1412  31  30  35  29  24 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号