(Note 2) ............................................. –40°C to 125°C
Storage Temperature Range................... –65°C to 150°C
PIN CONFIGURATION
TOP VIEW
V
IN
V
IN_REG
SHDN
CHRG
FAULT
TIMER
1
2
3
4
5
6
13
12 SW
11 BOOST
10 SENSE
9 BAT
8 NTC
7 V
FB
V
IN
V
IN_REG
SHDN
CHRG
FAULT
TIMER
1
2
3
4
5
6
TOP VIEW
12
11
10
9
8
7
SW
BOOST
SENSE
BAT
NTC
V
FB
13
DD PACKAGE
12-LEAD (3mm
×
3mm) PLASTIC DFN
T
JMAX
= 125°C,
θ
JA
= 43°C/W,
θ
JC
= 3°C/W
EXPOSED PAD (PIN 13) IS GND, MUST BE SOLDERED TO PCB
MSE PACKAGE
12-LEAD PLASTIC MSOP
T
JMAX
= 125°C,
θ
JA
= 43°C/W,
θ
JC
= 3°C/W
EXPOSED PAD (PIN 13) IS GND, MUST BE SOLDERED TO PCB
ORDER INFORMATION
LEAD FREE FINISH
LT3652HVEDD#PBF
LT3652HVIDD#PBF
LT3652HVEMSE#PBF
LT3652HVIMSE#PBF
TAPE AND REEL
LT3652HVEDD#TRPBF
LT3652HVIDD#TRPBF
LT3652HVEMSE#TRPBF
LT3652HVIMSE#TRPBF
PART MARKING*
LFRG
LFRG
3652HV
3652HV
PACKAGE DESCRIPTION
12-Lead Plastic DFN 3mm
×
3mm
12-Lead Plastic DFN 3mm
×
3mm
12-Lead Plastic MSOP
12-Lead Plastic MSOP
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/
3652hvfa
2
LT3652HV
ELECTRICAL CHARACTERISTICS
SYMBOL
V
IN
V
IN(OVLO)
V
IN(UVLO)
V
FB(FLT)
ΔV
RECHARGE
V
FB(PRE)
V
FB(PREHYST)
V
IN_REG(TH)
I
IN_REG
I
VIN
I
BOOST
I
BOOST/
I
SW
V
SW(ON)
I
SW(MAX)
V
SENSE(PRE)
V
SENSE(DC)
V
SENSE(C/10)
I
BAT
I
SENSE
I
VFB
I
VFB
V
NTC(H)
V
NTC(L)
V
NTC(HYST)
R
NTC(DIS)
I
NTC
V
SHDN
V
SHDN(HYST)
I
SHDN
V
CHRG
, V
FAULT
I
TIMER
V
TIMER(DIS)
PARAMETER
V
IN
Operating Range
V
IN
Start Voltage
OVLO Threshold
OVLO Hysteresis
UVLO Threshold
UVLO Hysteresis
Float Voltage Reference
Recharge Reference Threshold
Reference Precondition Threshold
Reference Precondition Threshold
Hysteresis
Input Regulation Reference
Operating Input Supply Current
The
l
denotes the specifications which apply over the full operating junction
temperature range, otherwise specifications are at T
A
= 25°C. V
IN
= 20V, Boost – SW = 4V,
SHDN
= 2V, V
FB
= 3.3V, C
TIMER
= 0.68µF.
CONDITIONS
V
BAT
= 4.2 (Notes 3, 4)
V
BAT
= 4.2 (Note 4)
V
IN
Rising
V
IN
Rising
(Note 6)
l
l
l
l
MIN
4.95
7.5
34
TYP
MAX
34
UNITS
V
V
V
V
V
V
V
V
mV
V
mV
35
1
4.6
0.2
40
4.95
3.318
3.34
3.282
3.26
3.3
82.5
2.3
70
Voltage Relative to V
FB(FLT)
(Note 6)
V
FB
Rising (Note 6)
Voltage Relative to V
FB(PRE)
(Note 6)
V
FB
= 3V; V
SENSE
– V
BAT
= 50mV
CC/CV Mode, I
SW
= 0
Standby Mode
Shutdown (SHDN = 0)
Switch On, I
SW
= 0,
2.5 < V
(BOOST – SW)
< 8.5
I
SW
= 2A
V
IN
– V
SW
, I
SW
= 2A
l
l
l
l
2.65
2.7
35
2.5
85
15
20
30
350
2.75
100
3.5
V
nA
mA
µA
µA
mA
mA/A
mV
A
mV
Input Regulation Reference Bias Current V
IN_REG
= V
IN_REG(TH)
BOOST Supply Current
BOOST Switch Drive
Switch-On Voltage Drop
Switch Current Limit
Precondition Sense Voltage
Maximum Sense Voltage
C/10 Trigger Sense Voltage
BAT Input Bias Current
SENSE Input Bias Current
V
FB
Input Bias Current
V
FB
Input Bias Current
NTC Range Limit (High)
NTC Range Limit (Low)
NTC Threshold Hysteresis
NTC Disable Impedance
NTC Bias Current
Shutdown Threshold
Shutdown Hysteresis
SHDN
Input Bias Current
Status Low Voltage
Charge/Discharge Current
Timer Disable Threshold
2.5
95
7.5
3
15
100
10
0.1
0.1
65
110
105
12.5
1
1
V
SENSE
– V
BAT
; V
FB
= 2V
V
SENSE
– V
BAT
; V
FB
= 3V (Note 7)
V
SENSE
– V
BAT
, Falling
Charging Terminated
Charging Terminated
Charging Terminated
CV Operation (Note 5)
V
NTC
Rising
V
NTC
Falling
% of threshold
Impedance to ground
V
NTC
= 0.8V
Rising
l
l
l
l
l
l
l
mV
mV
µA
µA
nA
nA
1.25
0.27
250
47.5
1.15
1.36
0.29
20
500
50
1.2
120
–10
1.45
0.315
V
V
%
kΩ
52.5
1.25
µA
V
mV
nA
10mA Load
l
0.4
25
0.1
0.25
V
µA
V
l
3652hvfa
3
LT3652HV
The
l
denotes the specifications which apply over the full operating junction
temperature range, otherwise specifications are at T
A
= 25°C. V
IN
= 20V, Boost – SW = 4V,
SHDN
= 2V, V
FB
= 3.3V, C
TIMER
= 0.68µF.
SYMBOL
t
TIMER
PARAMETER
Full Charge Cycle Timeout
Precondition Timeout
Timer Accuracy
f
O
DC
Operating Frequency
Duty Cycle Range
Continuous Operation
l
l
ELECTRICAL CHARACTERISTICS
CONDITIONS
MIN
TYP
3
22.5
MAX
UNITS
hr
min
–10
1
15
10
90
%
MHz
%
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
The LT3652HV is tested under pulsed load conditions such that
T
J
≅
T
A
. The LT3652HVE is guaranteed to meet performance specifications
from 0°C to 85°C junction temperature. Specifications over the –40°C
to 125°C operating junction temperature range are assured by design,
characterization, and correlation with statistical process controls. The
LT3652HVI specifications are guaranteed over the full –40°C to 125°C
operating junction temperature range. High junction temperatures degrade
operating lifetimes; operating lifetime is derated for junction temperatures
greater than 125°C.
Note 3:
V
IN
minimum voltages below the start threshold are only
supported if (V
BOOST
-V
SW
) > 2V.
Note 4:
This parameter is valid for programmed output battery float
voltages ≤ 4.2V. V
IN
operating range minimum is 0.75V above the
programmed output battery float voltage (V
BAT(FLT)
+ 0.75V). V
IN
Start
Voltage is 3.3V above the programmed output battery float voltage
(V
BAT(FLT)
+ 3.3V).
Note 5:
Output battery float voltage (V
BAT(FLT)
) programming resistor
divider equivalent resistance = 250k compensates for input bias current.
Note 6:
All V
FB
voltages measured through 250k series resistance.
Note 7:
V
SENSE(DC)
is reduced by thermal foldback as junction temperature
RT: The primary and secondary sides need to be isolated, output 12V, and the output current is at least 0.3A. One of my previous solutions used DM07652R. Please recommend the power IC you are using or...
[Abstract ] This paper analyzes electromagnetic interference and its interference mechanism on PLC control system, points out that the anti-interference performance of the control system must be consi...
I have just started to use MCU and I am still not very clear about many issues. This is to display the voltage value directly on the digital tube (I searched on the Internet). But I want to send the v...
UWB is regarded as a new function of the next generation of human-computer interaction due to its high precision and high security. As Samsung, Apple, Xiaomi and other mobile phones have introduced UW...
Want to be the most valuable employee in the company? Then you must stop saying "I can't do it" and take the initiative to volunteer. Does everyone want to be the MVP of the company? Then you must sto...
The core of a machine vision system is image acquisition and processing. All information comes from images, and image quality is crucial to the entire vision system. A good image can improve the st...[Details]
Ever since the Tesla fire incident, electric cars, already known for their poor reputation, have been subjected to even more scathing criticism. Despite this, many people are still willing to buy t...[Details]
The structure of an LCD TV primarily consists of the LCD display module, power module, driver module (primarily including the main driver board and tuner board), and keypad module. LCD display modu...[Details]
Smartphones have become essential digital devices, and the growing number of smartphone-centric applications is enriching people's lives. As users, they desire a better app experience and a wider r...[Details]
A tubular motor is an electric motor that is typically used to control the movement of machines and equipment. Tubular motors are generally divided into two categories: linear tubular motors and ro...[Details]
A scale, a large, ground-mounted scale, is typically used to measure the tonnage of truck cargo. It's the primary weighing device used in factories, mines, and businesses for bulk cargo measurement...[Details]
introduction
The OMAP-L138 dual-core processor is a new generation of low-power single-chip systems (SoCs) from TI. It is widely used in communications, industrial, medical diagnostic, and aud...[Details]
In microwave amplification circuits, the power chip is the core of the entire circuit. A large number of semiconductor devices in the chip will generate a lot of heat when working. If the heat diss...[Details]
In July 2025, stimulated by the "old for new" policy, China's new energy vehicle penetration rate reached a historic 50% mark. While industry experts like Cui Dongshu celebrated the market's perfor...[Details]
BMW has launched a new intelligent electronic and electrical architecture, which officials say is the world's first architecture that can be applied to all power types and all vehicle levels.
...[Details]
1. Introduction to power amplifier circuit
1. Generally speaking, the main function of a power amplifier circuit is to allow the load to obtain maximum power without distorting the signal or c...[Details]
1. Installing an industrial robot usually requires the following steps:
1. Determine the installation location: Determine the location and direction of the robot installation according to the ...[Details]
Comparison instructions compare two numbers, IN1 and IN2, of the same data type. IN1 and IN2 are located above and below the contact, respectively, and their data types must be the same. Operands c...[Details]
Robots are rapidly being deployed in diverse scenarios. Flexible, easy-to-use, and fast-to-deploy robots can be quickly adapted to diverse application scenarios across various industries, making th...[Details]
The internet is undergoing astonishing changes every minute: 299 million Teams meetings are recorded, 251 million emails are sent, $43.6 million is spent online, and 1.389 billion Facebook and Inst...[Details]
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
