I use C51 to read the time information of DS1687, and then send it to 16*8LED dot matrix for display. I don't know how to split the display, please give me some advice....
I have a program that uses 2553 to send AD data to the computer through UART, and then uses labview to make a virtual voltmeter. But my problem now is that no matter how I change the external power su...
First level: I'm here. The typical example of this level is that you can use C language to write simple logic control, such as flashing LED, simple digital tube display, and simple peripheral module d...
[font=Arial]Due to the rapid development of ultra-large-scale integrated circuit technology, digital signal processing technology, namely DSP (Digital Signal Processor) technology, has also developed ...
[i=s] This post was last edited by dontium on 2015-1-23 13:24 [/i] How is the transfer function of →→→→→→→→ derived?I have the corresponding mathematical foundation, but I just want to find an example...
Recently, the first Digital China Summit was held in Fuzhou, attracting many domestic ICT industry giants to participate in the exhibition. The long queues outside the venue, the noisy and exciting...[Details]
Wang Xiaochuan, the "Wudaokou Goalkeeper", is going through a level that he has never gone through before. For example, Sogou's (NYSE: SOGO) financial report, artificial intelligence, and the futur...[Details]
Using Systick timer to achieve delay 1. SysTick timer characteristics The SysTick timer is a 24-bit down counter, that is, when vlue is decremented to 0, an interrupt is triggered and the load va...[Details]
When the domestic discussion about "ZTE being banned" was hot, Alibaba officially announced the acquisition of chip supplier
Zhongtianwei
, but the investment amount was not disclosed. At t...[Details]
Chip: STM32F103C8T6 Application Pin: Output: PA0, PA1 TIM2 CH2 channel To achieve 50HZ (20ms) adjustable PWM output on the PA1 pin, set the system TIMx_CNT=8MHZ=8000 000HZ, set TIMx_PSC=800-1, then T...[Details]
0. Preparation First use st-link to connect the stm32 core board and PC for burning St-link Stm32 3.3V 3.3V GND GND SWDIO PART SWCLK DCLK Then connect with USB serial port board to v...[Details]
Our photovoltaic power station starts working at 5:30 in the morning. When you are still sleeping, the inverter starts working to make money!
Some people are skeptical. The sun hasn't even...[Details]
From concept proposal, prototype exploration, technology accumulation to product iteration and industrial development,
VR
has gradually expanded from the military market to the consumer market...[Details]
At the beginning of the new year of 2018, after the release of the national photovoltaic policy, we found that the state’s support for village-level poverty alleviation power stations has not weake...[Details]
Similar to the development trend of photovoltaic modules, photovoltaic inverters are also one of the examples of China's successful localization of manufacturing and leading the global market and tech...[Details]
1. Function and purpose There are two pins BOOT0 and BOOT1 on each STM32 chip. The level status of these two pins when the chip is reset determines which area the program starts from after th...[Details]
If you do not use an external crystal on the STM32, the connection method of OSC_IN and OSC_OUT If you use the internal RC oscillator instead of an external crystal, please follow the following metho...[Details]
The key is the configuration of registers. The T1 timer (16 bits) of CC2530 needs to configure three registers: T1CTL, T1STAT, IRCON Here is just a brief introduction. For more details, please refer ...[Details]
MCS-51 single-chip microcomputer timer/counter experiment programming program Programming requirements: 1. Connect a light-emitting diode LED to the P1.0 pin, light up for two seconds, turn off for o...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
