EEWORLDEEWORLDEEWORLD

Part Number

Search

3GV8C-80N-50.01

Description
LVCMOS Output Clock Oscillator, 50.01MHz Nom, ROHS COMPLIANT, DIP-8/4
CategoryPassive components    oscillator   
File Size125KB,1 Pages
ManufacturerEuroquartz
Websitehttp://www.euroquartz.co.uk/
Environmental Compliance  
Download Datasheet Parametric View All

3GV8C-80N-50.01 Overview

LVCMOS Output Clock Oscillator, 50.01MHz Nom, ROHS COMPLIANT, DIP-8/4

3GV8C-80N-50.01 Parametric

Parameter NameAttribute value
surface mountNO
Installation featuresTHROUGH HOLE MOUNT
Maximum operating temperature70 °C
Minimum operating temperature
physical size12.8mm x 12.8mm x 5.08mm
Is it lead-free?Yes
Is it Rohs certified?Yes
package instructionROHS COMPLIANT, DIP-8/4
Reach Compliance Codecompliant
Is SamacsysN
YTEOL0
Objectid1063499635
maximum symmetry55/45 %
Maximum control voltage1.85 V
Minimum control voltage1.45 V
Frequency Adjustment - MechanicalNO
Frequency offset/pull rate80 ppm
linearity10%
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
Oscillator typeLVCMOS
Output load15 pF
Nominal supply voltage3.3 V
frequency stability100%
Nominal operating frequency50.01 MHz
EURO
QUARTZ
8 pin Dual-in-Line VCXO
Frequency range 50.01MHz to 200MHz
LVCMOS Output
Supply Voltage 3.3 VDC
High Q fundamental mode crystal
Low jitter multiplier circuit
Low unit cost
GV8 VCXO
50.01MHz ~ 200.0MHz
DESCRIPTION
GV8 VCXOs, are packaged in an industry-standard, 8 pin Dual in Line
package. The VCXO incorporates a high Q fundamental mode crystal
and a low jitter multiplier circuit.
SPECIFICATION
Frequency Range:
Supply Voltage:
Output Logic:
Integrated Phase Jitter:
Period Jitter RMS:
Period Jitter Peak to peak:
Phase Noise:
Initial Frequency Accuracy:
Output Voltage HIGH (1):
Output Voltage LOW (0):
Pulling Range:
Temperature Stability:
Output Load:
Start-up Time:
Duty Cycle:
Rise/Fall Times:
Current Consumption:
Linearity:
Modulation Bandwidth:
Input Impedance:
Slope Polarity:
(Transfer function)
50.01MHz to 200.0MHz
3.3 VDC ±5%
LVCMOS
2.3ps typical, 4.0ps maximum
(for 155.250MHz)
4.0ps typical (for 155.250MHz)
27.0ps typical (for 155.250MHz)
Tune to the nominal frequency
with Vc= 1.65 ±0.2VDC
90% Vdd minimum
10% Vdd maximum
From ±30ppm to ±150ppm
15pF
10ms maximum, 5ms typical
50% ±5% measured at 50% Vdd
1.2ns typical (15pF load)
25mA maximum (15pF load)
10% maximum, 6% typical
25kHz minimum
2 MW minimum
Monotonic and Positive. (
PHASE NOISE
Offset
10Hz
100Hz
1kHz
10kHz
100kHz
1MHz
10MHz
Frequency 155.25MHz
-65dBc/Hz
-95dBc/Hz
-120dBc/Hz
-128dBc/Hz
-122dBc/Hz
-120dBc/Hz
-140dBc/Hz
Storage Temperature:
Ageing:
Enable/Disable (Tristate):
RoHS Status:
-50° to +100°C
±5ppm per year maximum
Not available (
Fully compliant
)
PART NUMBER SCHEDULE
Example:
FREQUENCY STABILITY
Stability Code Stability ±ppm Temp. Range
A
25
0°~+70°C
B
50
0°~+70°C
C
100
0°~+70°C
D
25
-40°~+85°C
E
50
-40°~+85°C
F
100
-40°~+85°C
If non-standard frequency stability is required
Use ‘I’ followed by stability, i.e. I20 for ±20ppm
3GV8B-80N-155.25
Supply Voltage
3 = +3.3V
Series Designator
GV8
Stability over temperature range
(
)
Pullability in ±ppm
Pullability determinator
N = minimum
M = maximum
T = Typical
Frequency in MHz
EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE
Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 info@euroquartz.co.uk www.euroquartz.co.uk
MicroPython now supports ESP32-C3
In the released micropython update, support for esp32-C3 with risc-v structure was added.tools/ci.sh: Build GENERIC_C3 board as part of esp32 CI. esp32/boards/GENERIC_C3: Add generic C3-based board. e...
dcexpert MicroPython Open Source section
Moderator, how do I use serial port 1?
Moderator, I am using 207R8 and want to use serial port 1. How can I configure the registers to make it send and receive like a normal microcontroller serial port? There are too many registers to conf...
gshlsh stm32/stm8
Why was my post deleted?
Can't you post like that, moderator? Please explain it clearly even if you die? ?...
neesam Embedded System
What filtering effect is better in this case?
I recently used AD698 to detect displacement. I used an oscilloscope to find that the DC voltage output by 698 had ripples, about 10mv, tens of Hz, even when powered by batteries! I wanted to use a si...
liweiliang Analog electronics
How to modify the keil background color
My Keil background color is black, I want to change it to white, how can I do it? Thank you!...
chenbingjy stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 856  617  2508  1632  2888  18  13  51  33  59 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号