2.5V / 3.3V 32:16 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
QUICKSWITCH
®
PRODUCTS
2.5V / 3.3V 32:16 MUX/DEMUX
HIGH BANDWIDTH BUS SWITCH
FEATURES:
DESCRIPTION:
IDTQS3VH16233
• N channel FET switches with no parasitic diode to Vcc
−
Isolation under power-off conditions
−
No DC path to Vcc or GND
−
5V tolerant in OFF and ON state
• 5V tolerant I/Os
• Low R
ON
- 4Ω typical
Ω
• Flat R
ON
characteristics over operating range
• Rail-to-rail switching 0 - 5V
• Bidirectional dataflow with near-zero delay: no added ground
bounce
• Excellent R
ON
matching between channels
• Vcc operation: 2.3V to 3.6V
• High bandwidth - up to 500 MHz
• LVTTL-compatible control Inputs
• Undershoot Clamp Diodes on all switch and control Inputs
• Low I/O capacitance, 4pF typical
• Available in SSOP and TSSOP packages
The QS3VH16233 HotSwitch is a 32-bit to 16-bit high bandwidth bus
switch, which can multiplex or demultiplex data. The QS3VH16233 has
very low ON resistance, resulting in under 250ps propagation delay
through the switch. This device can be used as two 16-bit to 8-bit
multiplexers or as one 32-bit to 16-bit multiplexer. SELx inputs control the
data flow. TESTx inputs control either one or two ports connection. In the
OFF and ON states, the switches are 5V-tolerant. In the OFF state, the
switches offer very high impedance at the terminals.
The combination of near-zero propagation delay, high OFF impedance,
and over-voltage tolerance also makes the QS3VH16233 ideal for high
performance communications applications.
The QS3VH16233 is characterized for operation from -40°C to +85°C.
APPLICATIONS:
•
•
•
•
•
Hot-swapping
10/100 Base-T, Ethernet LAN switch
Low distortion analog switch
Replaces mechanical relay
ATM 25/155 switching
FUNCTIONAL BLOCK DIAGRAM
TEST
1
TEST
2
SEL
1
x = 1 through 8
SEL
2
x = 9 through 16
xB
2
xA
xB
1
O NE O F EIG HT CHA NNE LS
O NE OF E IGHT CHANNE LS
xB
2
xA
xB
1
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
INDUSTRIAL TEMPERATURE RANGE
1
c
2003 Integrated Device Technology, Inc.
AUGUST 2003
DSC-5882/6
IDTQS3VH16233
2.5V / 3.3V 32:16 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
PIN CONFIGURATION
1
A
2
B
1
2
B
2
3
A
4
B
1
4
B
2
5
A
6
B
1
6
B
2
7
A
8
B
1
8
B
2
ABSOLUTE MAXIMUM RATINGS
(1)
Symbol
Description
Supply Voltage to Ground
DC Switch Voltage V
S
DC Input Voltage V
IN
AC Input Voltage (pulse width
≤20ns)
DC Output Current (max. current/pin)
Storage Temperature
Max.
– 0.5 to 4.6
– 0.5 to 5.5
– 0.5 to 5.5
–3
120
-65 to +150
Unit
V
V
V
V
mA
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
1
B
1
1
B
2
2
A
3
B
1
3
B
2
4
A
5
B
1
5
B
2
6
A
7
B
1
7
B
2
8
A
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
V
TERM(2)
V
TERM(3)
V
TERM(3)
V
AC
I
OUT
T
STG
°
C
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may
cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the
operational sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect reliability.
2. V
CC
terminals.
3. All terminals except V
CC
.
GND
Vcc
9
A
10
B
1
10
B
2
11
A
12
B
1
12
B
2
13
A
14
B
1
14
B
2
15
A
16
B
1
16
B
2
GND
Vcc
9
B
1
9
B
2
10
A
11
B
1
11
B
2
12
A
13
B
1
13
B
2
14
A
15
B
1
15
B
2
16
A
CAPACITANCE
Symbol
C
IN
C
I/O
C
I/O
Parameter
(1)
Control Inputs
(T
A
= +25 C, f = 1MHz, V
IN
= 0V, V
OUT
= 0V)
Typ.
3
Mux
Demux
Mux
Demux
8
4
16
8
Max.
5
12
6
24
12
pF
Unit
pF
pF
o
Quickswitch Channels
(Switch OFF)
Quickswitch Channels
(Switch ON)
NOTE:
1. This parameter is guaranteed but not production tested.
PIN DESCRIPTION
Pin Names
xA
xBx
SELx
TESTx
I/O
I/O
I/O
I
I
Bus A
Bus B
Data Select
Port Select
Description
TEST
1
TEST
2
SEL
1
SEL
2
SSOP/ TSSOP
TOP VIEW
FUNCTION TABLE
(1)
SELx
L
H
X
TESTx
L
L
H
xA
xB
1
xB
2
xB
1,
xB
2
Function
xA to xB
1
xA to xB
2
xA to xB
1
and xB
2
NOTE:
1. H = HIGH Voltage Level
L = LOW Voltage Level
X = Don't Care
2
IDTQS3VH16233
2.5V / 3.3V 32:16 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
(1)
Following Conditions Apply Unless Otherwise Specified:
Industrial: T
A
= –40°C to +85°C, V
CC
= 3.3V ± 0.3V
Symbol
V
IH
V
IL
I
IN
I
OZ
I
OFF
R
ON
Parameter
Input HIGH Voltage
Input LOW Voltage
Input Leakage Current (Control Inputs)
Off-State Current (Hi-Z)
Data Input/Output Power Off Leakage
Switch ON Resistance
Test Conditions
Guaranteed Logic HIGH
for Control Inputs
Guaranteed Logic HIGH
for Control Inputs
V
CC
= 2.3V to 2.7V
V
CC
= 2.7V to 3.6V
V
CC
= 2.3V to 2.7V
V
CC
= 2.7V to 3.6V
Min.
1.7
2
—
—
—
—
—
I
ON
= 30mA
I
ON
= 15mA
I
ON
= 30mA
I
ON
= 15mA
—
—
—
—
Typ.
(1)
—
—
—
—
—
—
—
6
7
4
5
Max.
—
—
0.7
0.8
±1
±1
±1
8
9
6
8
Ω
µA
µA
µA
V
Unit
V
≤
V
CC
0V
≤
V
OUT
≤
5V, Switches OFF
V
IN
or V
OUT
0V to 5V, V
CC
= 0V
V
CC
= 2.3V
V
CC
= 3V
V
IN
= 0V
V
IN
= 0V
V
IN
= 2.4V
(Typ. at V
CC
= 2.5V) V
IN
= 1.7V
0V
≤
V
IN
NOTE:
1. Typical values are at V
CC
= 3.3V and T
A
= 25°C, unless otherwise noted.
TYPICAL ON RESISTANCE vs V
IN
AT V
CC
= 3.3V
16
R
ON
(ohms)
14
12
10
8
6
4
2
0
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
V
IN
(Volts)
3
IDTQS3VH16233
2.5V / 3.3V 32:16 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
POWER SUPPLY CHARACTERISTICS
Symbol
I
CCQ
∆I
CC
I
CCD
Parameter
Quiescent Power Supply Current
Power Supply Current
(2,3)
per Input HIGH
Dynamic Power Supply Current
(4)
Test Conditions
(1)
V
CC
= Max., V
IN
= GND or V
CC
, f = 0
V
CC
= Max., V
IN
= 3V, f = 0 per Control Input
V
CC
= 3.3V, A and B Pins Open, Control Inputs
Toggling @ 50% Duty Cycle
NOTES:
1. For conditions shown as Min. or Max., use the appropriate values specified under DC Electrical Characteristics.
2. Per input driven at the specified level. A and B pins do not contribute to
∆Icc.
3. This parameter is guaranteed but not tested.
4. This parameter represents the current required to switch internal capacitance at the specified frequency. The A and B inputs do not contribute to the Dynamic Power Supply
Current. This parameter is guaranteed but not production tested.
Min.
—
—
Typ.
1.5
—
Max.
3
30
Unit
mA
µA
See Typical I
CCD
vs Enable Frequency graph below
TYPICAL I
CCD
vs ENABLE FREQUENCY CURVE AT V
CC
= 3.3V
20
18
16
14
12
I
CCD
(mA)
10
8
6
4
2
0
0
2
4
6
8
10
12
14
16
18
20
ENABLE FREQUENCY (MHz)
4
IDTQS3VH16233
2.5V / 3.3V 32:16 MUX/DEMUX HIGH BANDWIDTH BUS SWITCH
INDUSTRIAL TEMPERATURE RANGE
SWITCHING CHARACTERISTICS OVER OPERATING RANGE
T
A
= -40°C to +85°C
V
CC
= 2.5 ± 0.2V
(1)
Symbol
t
PLH
t
PHL
t
BX
t
PZH
t
PZL
t
PHZ
t
PLZ
t
PZH
t
PZL
t
PHZ
t
PLZ
f
Sx
Parameter
Data Propagation Delay
(2,3)
A to B or B to A
Switch Multiplex Delay
SEL to xA
Switch Turn-On Delay
SEL to xBx
Switch Turn-Off Delay
SEL to xBx
Switch Turn-On Delay
TEST to xBx
Switch Turn-Off Delay
TEST to xBx
Operating Frequency - Enable
(2,5)
1.5
1.5
1.5
1.5
1.5
⎯
9
9
7.5
8.5
8.5
7.5
1.5
1.5
1.5
1.5
1.5
⎯
7.5
8
7.5
9
8.5
15
ns
ns
ns
ns
ns
MHz
Min
.
(4)
⎯
Max.
V
CC
= 3.3 ± 0.3V
(1)
Min
.
(4)
⎯
Max.
Unit
ns
0.2
0.2
NOTES:
1. See Test Conditions under TEST CIRCUITS AND WAVEFORMS.
2. This parameter is guaranteed but not production tested.
3. The bus switch contributes no propagation delay other than the RC delay of the ON resistance of the switch and the load capacitance. The time constant for the switch alone
is of the order of 0.2ns at C
L
= 50pF. Since this time constant is much smaller than the rise and fall times of typical driving signals, it adds very little propagation delay to the
system. Propagation delay of the bus switch, when used in a system, is determined by the driving circuit on the driving side of the switch and its interaction with the load on
the driven side.
4. Minimums are guaranteed but not production tested.
5. Maximum toggle frequency for Sx control input (pass voltage > V
Dear engineers,I recently downloaded the flashapi of f2812 on the Internet. When I transplanted it to my program, I found that the compilation error was as follows:\"C:\\ti\\c2000\\cgtools\\bin\\cl200...
Application of NI test instruments in temperature and humidity testing THOMSON SDM-Shenzhen Deputy Manager Tang Qingan Keywords: temperature and humidity test chamber , sensor, module...
[align=left]I saw an article on Altera's official technical forum - "The Founding Years of Altera" [url=http://www.alteraforum.com.cn/showtopic-5405.aspx%20]http://www.alteraforum.com.cn/showtopic-540...
Work Department: Software Department Job Title: Embedded Development Engineer Job Responsibilities: System Porting, Driver Development, Application Programming Nature of Work: Full-time Salary Range: ...
I want to implement the built-in PWM function of msp430f1491. I encountered a problem, that is, the do while in void Init_CLK(void) is in an infinite loop. I can't figure it out. I would like to ask e...
When the WDP500-2A plane grating monochromator is used to test the emission wavelength of a high-power laser diode at different currents, the matching of the laser diode has the disadvantages of lo...[Details]
0. Introduction
In daily life, we often see some special-purpose vehicles. When these vehicles pass through intersections, they often obtain the right of way at intersections by temporarily op...[Details]
1. Background:
The instrument system parameter detection and control of the chemical production workshop of Tangshan Coal Gas Coking Plant are all analog instruments, some of which are eve...[Details]
General LED lighting has a current limiting resistor in the driving circuit, and the power consumed by the resistor has nothing to do with the LED light emission. In order to improve efficiency, a...[Details]
0 Introduction
With the rise and continuous improvement of the solid-state lighting industry, light-emitting diodes (LEDs) have become an alternative lighting technology and are gr...[Details]
According to the Industrial Technology Research Institute of Taiwan, due to factors such as the oil crisis and global warming, the issues of energy conservation and environmental protection have at...[Details]
Only a small number of LED manufacturers can produce high-quality LEDs. For applications that are only used for simple indication, low-quality LEDs are sufficient. However, high-quality LEDs must...[Details]
1. Introduction
With the increasing popularity of fully automatic washing machines, consumers have higher and higher requirements for their environmenta...[Details]
Introduction
As the country increases its efforts to control the atmospheric environment, motorcycle emission regulations will become stricter year by year, and motorcycles that do not meet the...[Details]
Fruit planting is an important part of China's agricultural development, and fruit tree pest control operations are becoming more and more important. At present, the overall level of pesticide applica...[Details]
A few days ago, I bought an 8LED flashlight in the market (the flashlight uses No. 5 batteries). Because I had other things to do, I didn't pay attention when purchasing it. When I got home and use...[Details]
The emergence and development of street lamps are inseparable from the prosperity and progress of cities, which makes street lamps useful. Conversely, street lamps also make the night of the city n...[Details]
LED is now known as the fourth generation of light sources. High-power LED has many advantages over traditional light sources in outdoor lighting.
1 LED lamps have high light efficiency
C...[Details]
Currently, the commonly used solar cell technologies include monocrystalline silicon solar cells and polycrystalline silicon thin-film solar cells. Production process: Monocrystalline silicon solar...[Details]
Nowadays, more and more people have digital cameras. The convenience and speed of digital cameras have gradually replaced film cameras and become the main tool for people's daily photography. The n...[Details]
Recruitment
京公网安备 11010802033920号
EEWORLD
