The compact DFA20 Series provides power densities up to 11 watts
per cubic inch (0.67 watts per cm
3
). Ideal for battery operated
industrial, medical control and remote data collection systems, this
converter has fully filtered inputs and outputs. Complete overload
protection with independent pulse-by-pulse current limiting and an
overtemperature shutdown ensures reliable system operation. The
output of the converter is electrically isolated, thereby allowing the
output to be configured as a positive or negative output voltage.
FEATURES
• Remote ON/OFF and TRIM
• Overcurrent Protection and Thermal Shutdown
• Efficiencies to 83%
• 700V Isolation, Up to 1544V on 48V Converters
• Power Density up to 11 Watts per Cubic Inch
• Five-Side Shielded Case
• Extended Range Input (2:1)
BOTTOM VIEW
2.02
(51.31)
SIDE VIEW
0.040 (1.02) DIA
6 PLACES
0.700
(17.78)
0.600
(15.24)
0.400
(10.16)
0.300
(7.62)
0.000
0.100
(2.54)
0.51
(13.0)
5
1
2
6
2.02
(51.31)
3
7
0.25
(6.35)
0.11
(2.8)
0.000
1.800
(45.72)
Mechanical tolerances unless otherwise noted:
X.XX dimensions: ±0.020 inches
X.XXX dimensions: ±0.005 inches
NOTES
(1) All parameters measured at Tc = 25°C, nominal input voltage and full rated load unless otherwise noted.
Refer to the Technical Reference Section for the definition of terms, measurement circuits and other
information.
(2) The Case is tied to the -Input, Pin 2.
(3) The functional temperature range is intended to give an additional data point for use in evaluating this
power supply. At the low functional temperature the power supply will function with no side effects,
however, sustained operation at the high functional temperature will reduce expected operational life.
The data sheet specifications are not guaranteed beyond the case operating range.
(4) The case thermal impedance is specified as the case temperature rise over ambient per package watt
dissipated.
0.45
(11.43)
0.000
Rev. 04/2000
1
DFA20 SERIES – SINGLE OUTPUT
NOTES
(1)
All parameters measured at Tc=25°C, nominal input voltage and full rated load unless otherwise
noted. Refer to the Technical Reference Section for the definition of terms, measurement circuits and
other information.
Noise is measured per Technical Reference Section. Measurement bandwidth is 0-20 MHz for peak-
peak measurements, 10 kHz to 1 MHz for RMS measurements. Output noise is measured with a
0.01µF ceramic in parallel with a 1µF/35V Tantalum capacitor located 1" away from the converter to
simulate your PCB’s standard decoupling. Input reflected ripple is measured into a 10µH source
impedance.
(3)
(4)
Short term stability is specified after a 30 minute warmup at full load, constant line and recording
the drift over a 24 hour period.
The input ripple rejection is specified for DC to 120 Hz ripple with a modulation amplitude of 1% of
Vin.
(2)
2
DFA20 SERIES – SINGLE OUTPUT
DFA20 SERIES APPLICATION NOTES:
External Capacitance Requirements
No external capacitance is required for operation of the DFA20
Series. The use of input capacitors with less than 0.5 ESR may
cause peaking in the input filter and degrade filter performance.
External output capacitance is not required for operation, however
it is recommended that 1 F to 10 F of tantalum and 0.001 to
0.1 F ceramic capacitance be selected for reduced system noise.
Additional output capacitance may be added for increased
filtering, but should not exceed 400 F.
Negative Outputs
A negative output voltage may be obtained by connecting the
+OUT to circuit ground and connecting -OUT as the negative
output.
Remote ON/OFF Operation
The remote ON/OFF pin may be left floating if this function is not
used. It is recommended to drive this pin with an open collector
arrangement or a relay contact. When the ON/OFF pin is pulled
low with respect to the -INPUT, the converter is placed in a low
power drain state.
Output TRIM
The TRIM pin may be used to adjust the output ±5% from the
nominal setting. This function allows adjustment for voltage drops
in the system wiring, as well 5.2 volt outputs for ECL applications.
Figure 1 shows the proper connections to use this function. A
trimpot value of 10K should be used for 3.3 and 5 volt outputs.
A trimpot value of 20K should be used for 12 and 15 volt
outputs. If the TRIM function is not required the pin may be
left floating.
+OUT
5
TRIM
7
-OUT
6
USING TRIMPOT
10K
LOAD
+OUT
5
TRIM
DOWN
TRIM
7
-OUT
6
USING FIXED RESISTORS
LOAD
TRIM
UP
Figure 1.
DFA20 SERIES BLOCK DIAGRAM
OUTPUT POWER DERATING
20
ISOLATION TRANSFORMER
THERMAL SHUTDOWN
5
+
+ OUTPUT
15
POWER OUTPUT
+ INPUT
1
– INPUT
2
LC
INPUT
FILTER
CURRENT
MODE
PWM
6
- OUT
10
+
ON/OFF
7
TRIM
3
ISOLATED
FEEDBACK
–
5
FIVE SIDED SHIELDED COPPER CASE
LOW TC
BANDGAP
REFERENCE
0
50
60
70
80
90
AMBIENT TEMPERATURE
100
NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous environments,
or nuclear control systems without the express written consent of the President of Power-One, Inc.
TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are
The advent of synchronous digital systems has made the humble oscillator the heart of modern microprocessor-based digital systems. The thousands of applications for oscillators have created an extreme...
Abstract: This paper describes the development and design of a new type of automobile reversing radar product (reversing multimedia visual ranging terminal) hardware/software. Firstly, its advantages ...
When I use the HyperTerminal, I can clearly set the line break character as the end of the line to be sent. ButIt is actually processed byte by byte, and the speed feels very slow.Some people will say...
Keithley's 4200 Semiconductor Characterization System was used to bias the probes and acquire IC device leakage current and drain-source voltage ( IDVDS) data. The system was equipped with four 4200-S...
Whenever the security industry mentions development trends, the most frequently appearing words must be high-definition, digital, and intelligent. These are the three recognized development trends. Ho...
Event: The company simultaneously released its 2017 annual report and the first quarter report of 2018. In 2017, the company achieved revenue of 8.886 billion yuan, a year-on-year increase of 48.01...[Details]
The day before yesterday, I learned about STM's Systick and found it quite useful for precise timing. When I used CVAVR before, I found that the delay.h in it was very useful. So, I used STM32's...[Details]
China Energy Storage Network:
Blockchain + finance, blockchain + environmental protection, blockchain + insurance, even a roadside fried chicken shop is using the banner of blockchain + fried...[Details]
introduction In the general project development process, two or more microcontrollers are often required to communicate to complete data transmission. For example, a quadcopter wirelessly transmits d...[Details]
The adoption rate of serverless
cloud
computing
is gradually increasing, but it has not yet reached people's expectations. Various surveys show that serverless
is
still
an eme...[Details]
The day before yesterday, another mainland technology company submitted a prospectus to the Hong Kong Stock Exchange. The company is called "Jia Nan Creative (hereinafter referred to as 'Jia Nan')"...[Details]
As a leading company in automotive semiconductors, Freescale and Khronos Group have jointly launched an automotive multimedia embedded microprocessor i.MX35 with an integrated OpenVG hardware acceler...[Details]
Photovoltaic inverters are the core equipment of photovoltaic systems. Their main function is to convert the direct current generated by photovoltaic modules into alternating current that meets the...[Details]
Internal channels of ADC: In addition to using external channels to collect external analog voltage signals, the ADC of STM32 also has two internal channels 16 and 17. Channel 16 is connected to ...[Details]
One addend is in the on-chip RAM 40H, 41H, 42H units, the other addend is in the on-chip RAM 43H, 44H, 45H, and the sum is stored in the 50H, 51H, 52H units, with the carry bit stored in 00H. Please ...[Details]
Unfortunately, my serial port has some problems and I can't print information. I can only debug to view variables and see the values. Fortunately, there is not much AD conversion code, and I can use ...[Details]
The following comes from - "cortex-M3 Definitive Guide" Special function register group: Program Status Registers (PSRs or xPSRs) Interrupt mask register group (PRIMASK, FAULTMASK, and BASEPRI) ...[Details]
With the development of electronic devices, more and more people pay attention to flexible electronic devices, which refer to electronic devices that can still work under certain deformation condit...[Details]
Analogue and Mixed Signal
京公网安备 11010802033920号
EEWORLD
