.................................................-0.3V to (V
IN
+ 0.3V)
HOLD
to GND
........................................ -0.3V to (V
OUT
+ 0.3V)
SET, WDI, OUT to GND
.....................................-0.3V to +13.2V
RESET
to GND (Open Drain)
............................-0.3V to +13.2V
Short-Circuit Duration (V
IN
≤ +14V)
..........................Continuous
Maximum Current to Any Pin (Except IN, OUT)
..............±20mA
Continuous Power Dissipation (T
A
= +70°C)
8-Pin SO-EP (derate 19.2mW/°C above +70°C)
.......1538mW
Operating Temperature Range
......................... -40°C to +125°C
Junction Temperature ......................................................+150°C
Storage Temperature Range
............................ -65°C to +150°C
Lead Temperature (soldering, 10s)
................................. +300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Package Thermal Characteristics
(Note 1)
SO-EP
Junction-to-Ambient Thermal Resistance (θ
JA
)
...........41°C/W
Junction-to-Case Thermal Resistance (θ
JC
)..................2°C/W
Note 1:
Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a four-layer
board. For detailed information on package thermal considerations, refer to
www.maximintegrated.com/thermal-tutorial.
Electrical Characteristics
(V
IN
= +14V, I
OUT
= 1mA, C
IN
= 10μF, C
OUT
= 15μF, V
EN
= +2.4V,
HOLD
= open, 10kΩ from
RESET
to OUT, T
A
= -40°C to +125°C,
unless otherwise noted. Typical specifications are at T
A
= +25°C.) (Note 2)
PARAMETER
Input Voltage Range
Reverse Input Current
Supply Current
Shutdown Supply Current
REGULATOR
Guaranteed Output Current
I
OUT
V
OUT
= +5V
SET = GND, I
OUT
= 1mA to 150mA,
5V version
Output Voltage
V
OUT
SET = GND, I
OUT
= 1mA to 150mA,
3.3V version
I
OUT
= 5mA, adjustable version (MAX5024)
Dropout Voltage
Startup Response Time
Line Regulation
ΔV
OUT
/
ΔV
IN
ΔV
DO
I
LOAD
= 150mA, V
OUT
= +5V (Note 3)
Rising edge of V
IN
to V
OUT
, R
L
= 500Ω,
SET = GND
+8V ≤ V
IN
≤ +65V
+5V version
+3.3V version
-1
-0.5
150
4.8
3.168
2.5
0.9
400
+1
0.5
5
3.3
5.2
3.432
11
1.5
V
µs
mV/V
V
mA
SYMBOL
V
IN
I
REVERSE
I
Q
I
SHDN
V
IN
= -60V
Measured at GND
V
EN
≤ +0.4V
I
OUT
= 0mA
I
OUT
= 150mA
CONDITIONS
V
IN
must be at least 1.5V greater than V
OUT
MIN
6.5
0.1
58
2000
6
16
TYP
MAX
65
10
140
UNITS
V
µA
µA
µA
www.maximintegrated.com
Maxim Integrated │
2
MAX5023/MAX5024
65V, Low-Quiescent-Current, High-Voltage Linear
Regulators with μP Reset and Watchdog Timer
Electrical Characteristics (continued)
(V
IN
= +14V, I
OUT
= 1mA, C
IN
= 10μF, C
OUT
= 15μF, V
EN
= +2.4V,
HOLD
= open, 10kΩ from
RESET
to OUT, T
A
= -40°C to +125°C,
unless otherwise noted. Typical specifications are at T
A
= +25°C.) (Note 2)
PARAMETER
Enable Voltage
Enable Input Current
HOLD
Voltage
HOLD
Release Voltage
HOLD
Pullup Current
SET Reference Voltage
SET Input Leakage Current
Load Regulation
Power-Supply Rejection Ratio
Short-Circuit Current
Thermal-Shutdown
Temperature
Thermal-Shutdown Hysteresis
RESET CIRCUIT
MAX502_L, SET = GND
MAX502_M, SET = GND
MAX502_T, SET = GND
Reset Threshold
V
TH
MAX502_S, SET = GND
MAX5024L/T, SET = Divider
(Figure 1) (Note 4)
MAX5024M/S, SET = Divider
(Figure 1) (Note 4)
Reset Timeout Period
V
OUT
to Reset Delay
t
RP
t
RD
V
OUT
falling
140
4.50
4.25
2.970
2.805
4.625
4.375
3.052
2.887
4.75
4.50
3.135
2.970
V
SYMBOL
V
EN
I
EN
V
IL
V
IH
I
HOLD
V
SET
I
SET
ΔV
OUT
/
ΔI
OUT
PSRR
I
SC
T
J(SHDN)
ΔT
J(SHDN)
I
OUT
= 1mA to 150mA
I
OUT
= 10mA, f = 100Hz, 500mV
P-P
,
V
OUT
= +5V
V
IN
= +8V
175
CONDITIONS
EN = high, regulator on
EN = low, regulator off
V
EN
= +2.4V
V
EN
= +14V
Regulator on, EN transition from high to low
EN = low, regulator shuts off
Internally connected to OUT
I
OUT
= 10mA
1.223
V
OUT
- 0.4V
4
1.248
0.5
1
54
300
150
20
1.273
100
0.5
4
0.4
MIN
2.4
0.4
TYP
MAX
UNITS
V
µA
V
V
µA
V
nA
mV/mA
dB
mA
°C
°C
0.925 x V
OUT
0.875 x V
OUT
200
5
260
ms
µs
www.maximintegrated.com
Maxim Integrated │
3
MAX5023/MAX5024
65V, Low-Quiescent-Current, High-Voltage Linear
Regulators with μP Reset and Watchdog Timer
Electrical Characteristics (continued)
PARAMETER
SYMBOL
(V
IN
= +14V, I
OUT
= 1mA, C
IN
= 10μF, C
OUT
= 15μF, V
EN
= +2.4V,
HOLD
= open, 10kΩ from
RESET
to OUT, T
A
= -40°C to +125°C,
unless otherwise noted. Typical specifications are at T
A
= +25°C.) (Note 2)
CONDITIONS
V
OUT
≥ +1.0V, I
SINK
= 50µA,
RESET
asserted
Open-Drain
RESET
Output
Voltage (Note 5)
V
OL
V
OUT ≥ +2.85V, I
SINK
= 1.2mA,
RESET
asserted
V
OUT ≥ +4.25V, I
SINK
= 3.2mA,
RESET
asserted
Open-Drain
RESET
Output-
Leakage Current
WATCHDOG FUNCTION
Watchdog Timeout Period
WDI Pulse Width
WDI Input Voltage
WDI Input Current
Note
Note
Note
Note
Note
2:
3:
4:
5:
6:
t
WD
t
WDI
V
IL
V
IH
I
WDI
WDI = GND
2.4
-1
+1
(Note 6)
1.12
1.6
50
0.4
2.08
s
ns
V
µA
I
LKG
RESET
not asserted, V
RESET
= +11V
MIN
TYP
MAX
0.3
0.3
0.4
1.0
µA
V
UNITS
Limits at -40°C are guaranteed by characterization and not production tested.
Dropout voltage is defined as V
IN
- V
OUT
when V
OUT
is 100mV below the value of V
OUT
for V
IN
= V
OUT
+ 3V.
V
OUT
= V
SET
(1 + R1/R2) = 1.248V (1 + R1/R2).
RESET
is guaranteed to be in the correct logic state for V
This is the first technical seminar launched by Huaqing Farsight Embedded Training Center after May 1st. There will be two more special lectures on high-speed embedded and embedded Linux in July and S...
[i=s]This post was last edited by Beifang on 2022-1-17 15:14[/i]1. There is a step-by-step guide to creating a program, see AN1260: Integrating v3.x Silicon Labs Bluetooth Applications with Real-Time ...
C1=1000P, R1=10K determines the center frequency. R3=160 ohm, C2=0.1U in the low-pass filter. Pins 3 and 4 are short-circuited, which may not be clearly drawn in the diagram. Now input a signal of abo...
The image format captured from the dopoda S1 camera is RGB565 120*160 (obtained from DirectShow Filter). Before H.263 encoding, it must be converted to YUV format. The available formats of QCIF are fi...
How does this circuit achieve single live wire power supply? How does it control the bidirectional thyristor? How does it get power when the bidirectional thyristor is turned on? How does it get power...
1. Design Overview
1. Design Intent
The rapid development of medical imaging technology continues to promote the progress of modern medicine. CT, MRI, and PET are widely ...[Details]
With the development of the automobile industry, the complexity and information density of automobile information systems are increasing. Displays are no longer just basic centralized instrument di...[Details]
The hardware circuit principle is shown in Figure 1. In the specific design, each part should consider the anti-interference problem to minimize the impact of interference on the performance of the...[Details]
This summary will introduce the transmitter characteristic test of TD terminal products - uplink power control. According to the 3GPP TS34.122 standard, UE uplink power control is divided into uplink ...[Details]
Third generation (3G) mobile phones offer a variety of features with more functionality. As consumers enjoy the latest and better features of these communication devices, they continue to demand lo...[Details]
introduction
The most common flight state of a fixed-wing aircraft is horizontal flight. If it is allowed to fly at a large angle, the action cannot be maintained all the time. If it is al...[Details]
Introduction With the continuous development of economy, people's demand for automobiles is increasing day by day. Correspondingly, automobile consumer groups are becoming more and more mature. It...[Details]
Preface
In the analog era, due to the unchanged specifications and relatively simple device connections, as well as users' low requirements for image quality, the relatively simple environment...[Details]
1. What is fading?
In terms of scope, fading can be roughly divided into three types: large area fading, small area fading and indoor fading. As shown in Figure 1, large area fading refers t...[Details]
In recent years, the development of automotive electronic technology has significantly improved vehicle safety performance. One of the technologies that is expected to be widely used is the tire p...[Details]
Battery system architecture
For many years, nickel-cadmium batteries and later nickel-metal hydride battery technology have dominated the market. Lithium batteries have only entered ...[Details]
Nowadays, video conferencing has become a situation where multiple manufacturers supply various high-definition products. The technology of high-definition products has greatly matured, the cost h...[Details]
The full name of RFID is Radio Frequency Identification, which uses radio frequency to realize data transmission between programmable controller (PLC) or microcomputer (PC) and identification, ther...[Details]
1 Introduction
With the rise of my country's automobile industry, the demand for related in-vehicle electronic products is growing, and has become a research and development hotspot in the...[Details]
The growing global interest in green power has added new variables to the design of power supplies and power adapters. Designers must not only traditionally consider the design specifications requi...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
