The single output DGP30 Series is designed to accept an extended
2:1 input voltage range for use in industrial and telecom
applications. The output of the converter is electrically isolated,
thereby allowing the output to be configured as a positive or
negative output voltage. For additional system utility output Trim
and Remote ON/OFF are featured. Overcurrent protection,
overtemperature protection, and output overvoltage transient
protection allow safe, reliable operation.
FEATURES
• Remote ON/OFF and TRIM
• Low OFF Current
• Overcurrent and Overtemperature Protection
• Efficiencies to 86%
• Transient Output Overvoltage Protection
• 1544V Isolation
• Five-Side Shielded Case
• Extended Range Input (2:1)
BOTTOM VIEW
2.02
(51.31)
SIDE VIEW
0.040 (1.02) DIA
6 PLACES
0.700
(17.78)
0.600
(15.24)
0.400
(10.16)
0.300
(7.62)
0.000
0.100
(2.54)
0.31
(7.9)
0.11
(2.8)
0.000
5
1
2
6
1.62
(41.15)
3
7
0.3
(7.62)
1.800
(45.72)
Mechanical tolerances unless otherwise noted:
X.XX dimensions: ±0.020 inches
X.XXX dimensions: ±0.005 inches
NOTES
(1) All parameters measured at Tc = 25°C, nominal input voltage and full rated load unless otherwise noted.
Refer to the Technical Reference Section for the definition of terms, measurement circuits and other
information.
(2) ON/OFF pin is referenced to pin 2, -Input. See DGP30 Series Application Notes for the specific
requirements of this feature.
(3) The Case is electrically connected to Pin 1, +Input.
(4) Full output trim range may not be available at minimum input voltage and full load. Full trim is
guaranteed from minimum input voltage, plus 5%, and full load.
(5) The case thermal impedance is specified as the case temperature rise over ambient per package watt
dissipated.
Rev. 04/2000
1
0.55
(13.97)
0.000
DGP30 SERIES – SINGLE OUTPUT
NOTES
(1)
All parameters measured at Tc=25 °C case temperature, nominal input voltage and full rated load
unless otherwise noted. Refer to the Technical Reference Section for definition of terms,
measurement circuits and other information.
Minimum load required for rated regulation only. Module will not be damaged if run at less than
minimum load.
Short term stability is specified after a 30 minute warm-up at full load, and with constant line, load
and ambient conditions.
The input ripple rejection is specified for DC to 120Hz ripple with a modulation amplitude of 1% Vin.
Noise is measured per Technical Reference Section. Output noise is measured with a 1µF tantalum
capacitor connected 1” from the output pins.
(2)
(3)
(4)
(5)
For the Most Up-To-Date Information
www.power-one.com
24 Hours/Day—7 Days/Week
NUCLEAR AND MEDICAL APPLICATIONS Power-One products are not authorized for use as critical components in life support systems, equipment used in hazardous environments,
or nuclear control systems without the express written consent of the President of Power-One, Inc.
TECHNICAL REVISIONS The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are
subject to change without notice.
2
DGP30 SERIES – SINGLE OUTPUT
DGP30 SERIES APPLICATION NOTES:
External Capacitance Requirements
No external capacitance is required for operation of the DGP30
Series. However, it is recommended that the DGP30 Series use a
capacitor of sufficient ripple current capacity connected across the
input pins if a capacitive input source is farther than 1” from the
converter. To meet the reflected ripple requirements of the
converter, an input impedance of less than 0.05 Ohms from DC to
200KHz is required. External output capacitance is not required
for operation, however it is recommended that 1 F to 10 F of
tantalum and 0.001 to 0.1 F ceramic capacitance be selected for
reduced system noise. Additional output capacitance may be
added for increased filtering, but should not exceed 400 F.
Negative Outputs
A negative output voltage may be obtained by connecting the
+OUT to circuit ground and connecting -OUT as the negative
output.
Remote ON/OFF Operation
The remote ON/OFF pin may be left floating if this function is
not used. It is recommended to drive this pin with an open
collector arrangement or a relay contact. When the ON/OFF pin
is pulled low with respect to the -INPUT, the converter is placed
in a low power drain state. Since the ON/OFF pin is driven by a 9
volt internal source via a 100K resistor, the pin should not be
driven by TTL logic. Attempts to drive this circuit with logic
circuits may result in damage to user circuitry.
Output TRIM
The TRIM pin may be used to adjust the output ±5% from the
nominal setting. This function allows adjustment for voltage drops
in the system wiring, as well 5.2 volt outputs for ECL applications.
Figure 1 shows the proper connections to use this function. A
trimpot value of 10K should be used for the 5 volt output.
A trimpot value of 20K should be used for 12 and 15 volt outputs.
If the TRIM function is not required the pin may be left floating.
I use IAR for msp430 programming and assign a floating point number by float pressure = 1101.32;. During online debugging, I find that the variable pressure is not actually equal to 1101.32, but 1.101...
Bandwidth is a common indicator in frequency domain analysis. Common bandwidths of spectrum analyzers include resolution bandwidth and video bandwidth. This article will fully explain these concepts, ...
I would like to ask all the experts, as shown in Figure 1 and Figure 2, the antenna circuits used in the TI CC2541, both are patch ceramic antennas. I want to know what the difference is between these...
Abstract: This paper uses the time domain analysis method to obtain the relationship between the speed measurement error and the short stability of each oscillator in the measurement and control syste...
ZTE
The communication embargo incident has impacted the communication industry and sounded the alarm for the semiconductor industry. Let's follow the embedded editor to learn more about the r...[Details]
On April 19, it was reported that Alibaba DAMO Academy is developing a neural network chip, Ali-
NPU
, which is mainly used for
AI
reasoning calculations such as image and video analys...[Details]
1. Principle 1. Infrared emission protocol The infrared transmission protocol has been written in the previous article , so I will not repeat it here. 2. Timer counting and input capture A timer...[Details]
1. Function prototype In the function library officially provided by STM32, you can find functions like HAL_Delay(). This function uses a timer to achieve a more accurate time delay and provides it...[Details]
All relevant units:
In accordance with the relevant requirements of the provincial and municipal electric vehicle charging infrastructure construction work, in order to further standardize the...[Details]
This part of the code in the void SystemClock_Config(void) function in the main file generated by stm32cubemx RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE; This bug occurs, and the f...[Details]
Regarding the PHY construction of LWIP, the PHY chip used is LAN8720A, RMII mode. Regarding the hardware connection part, the Atomic board F407 is used, and the hardware connection is as follows: ...[Details]
Serial Port: 一. USART_ITConfig(USART1, USART_IT_TXE, ENABLE): As long as the transmit register is empty, there will always be an interrupt. Therefore, if you are not sending data, turn off the tran...[Details]
On the eve of Qingming Festival, the trade friction between China and the United States is on the rise. Let's follow the automotive electronics editor to learn more about the relevant content. Ba...[Details]
On April 16, the U.S. Department of Commerce announced that it would ban U.S. companies from selling parts, goods, software, and technology to
ZTE
for seven years, until March 13, 2025.
Th...[Details]
The parking assistance system is an important application of the active anti-collision system of automobiles in low-speed and complex urban environments, and is also a specific embodiment of the inte...[Details]
Artificial intelligence
There is no inherent bias in AI. It does not "think" something is true or false for reasons that cannot be explained by logic. Unfortunately, human bias exists in mach...[Details]
In most countries, the military is a fairly large group, and the health of soldiers is particularly important to the combat effectiveness of the army. The US Department of Defense's Advanced Resear...[Details]
*This article is based on the author's report at the "Embedded System Association Theme Discussion (Total 22nd) - Current Situation and Development Prospects of Internet of Things Operating Systems...[Details]
In January, Android 7.0 Marshmallow surpassed Lollipop three years ago to become the second most used Android version in the world. According to
the latest data from
Google
, a snapshot of d...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
