The WMS712x is a 64 non-volatile linear digital potentiometers available in 10KΩ, 50KΩ and 100KΩ
resistance values. The WMS7120/1 can be used as a three-terminal potentiometer or as a two
terminal variable resistor in a wide variety of applications.
The output of each potentiometer is determined by the wiper position, which varies in linearly between
V
A
and V
B
terminal according to the content stored in the volatile Tap Register (TR) which is
programmed through Up/Down (Increment/Decrement) interface. The channel has one non-volatile
memory location (NVMEM0) that can be directly written to by users through the Up/Down interface.
Power-on recall is also built in so the content of the NVMEM0 to Tap Register is automatically loaded.
The WMS7120/1 devices pin out the resistor wiper directly. The WMS7121 devices feature an output
buffer with 3mA minimum drive capability.
All the WMS7120/1 devices are single channel devices offered in 8-pin PDIP, SOIC and MSOP
packages. The WMS7120/1 devices operate over a wide operating voltage ranging from 2.7V to
5.5V.
2. FEATURES
•
•
•
•
•
•
•
•
•
•
•
•
•
Drop-in replacements for many popular parts
Available output buffer for WMS7121 devices
Single linear-taper channel
64 taps
10K, 50K and 100K end-to end resistance
V
SS
to V
DD
terminal voltages
Non-volatile storage of wiper positions with power-on recall
Data storage and potentiometer control through Up/Down (3-wire) interface
Endurance 100,000 write cycles
Data retention 100 years
Package options:
o
8-pin PDIP, SOIC or MSOP
Industrial temperature range: -40° ~ 85°C
Single supply operation 2.7V to 5.5V
-2-
WMS7120/1
3. BLOCK DIAGRAM
Tap Register
V
A
INC
CS
U/D
Up/Down
Serial
Interface
Decoder
V
W
V
B
NV Memory
V
SS
NV Memory
Control
NVMEM0
V
DD
FIGURE 1 – WMS7120 BLOCK DIAGRAM (Rheostat Mode)
Tap Register
V
A
INC
CS
U/D
Up/Down
Serial
Interface
Decoder
V
W
V
B
NV Memory
V
SS
NV Memory
Control
NVMEM0
V
DD
FIGURE 2 – WMS7121 BLOCK DIAGRAM (Divider Mode)
-3-
Publication Release Date: April 21, 2005
Revision 1.1
WMS7120/1
4. TABLE OF CONTENTS
1. GENERAL DESCRIPTION.................................................................................................................. 2
2. FEATURES ......................................................................................................................................... 2
Hello everyone, I am a sophomore student, and I am designing a blood oxygen saturation detector (for graduation project). Since I don't know much about 51, AVR microcontrollers, ARM, DSP and other pro...
I would like to ask whether the RTC module in ARM9 should be implemented as a driver or as a function in the OAL layer, and how to call the function of the RTC module under WINCE???...
Beijing UFIDA Technology Co., Ltd. is urgently looking for talents in circuits. The work location is Alcatel, Pudong, Shanghai. I hope that friends who are interested can contact me. Because the proje...
[i=s]This post was last edited by paulhyde on 2014-9-15 09:42[/i]Very good information for the electronic design competition. I hope everyone will actively download it. Hahahaha~~
Everyone, remember t...
Is there any other way to burn the bootloader into NAND flash besides JTAG? I am using a laptop without a serial or parallel port. I converted an RS232 using USB, but it still has no parallel port, so...
As a wireless broadband metropolitan area network standard, WiMAX technology has greater advantages than previous 3.5GHz MMDS products in terms of non-line-of-sight transmission and spectrum utiliz...[Details]
0. Introduction
In daily life, we often see some special-purpose vehicles. When these vehicles pass through intersections, they often obtain the right of way at intersections by temporarily op...[Details]
With the rapid development of urban economy, elevators are increasingly used as a vertical transportation tool. However, elevator fault detection and maintenance, especially the role of elevator remot...[Details]
1 Introduction
Building Automation System (BAS) is a distributed monitoring system (DCS) designed according to distributed information and control theory. It is the result of the mutual de...[Details]
1 Introduction
With the development of control, computer, communication, network technology, etc., a new control technology, namely fieldbus, has emerged in the field of industrial control...[Details]
LED is the abbreviation of light emitting diode, which is an electric light source made of semiconductor technology. The core part of LED is a chip composed of P-type semiconductor and N-type semi...[Details]
It is well known to automotive suppliers that automakers are demanding more from their supply base. For connector suppliers, this means stricter requirements for product performance, stability and ...[Details]
Abstract: With the development and construction of BeiDou II system, China will shift from the situation dominated by GPS to the situation dominated by BeiDou II global navigation system independen...[Details]
The era of mobile access to the Internet has arrived, and it will rapidly change the business and infrastructure needs of mobile operators under a whole new trend of requirements. We need 4G LTE to...[Details]
1 Embedded Systems
Embedded System refers to a collection of computer hardware and software with specific functions or purposes, which is divided into embedded software system and embe...[Details]
1 Introduction to LED
With the development of science and technology, people have higher and higher requirements on automobile light sources. LED (Light Emitting Diode) has gradually attracted...[Details]
LED is now known as the fourth generation of light sources. High-power LED has many advantages over traditional light sources in outdoor lighting.
1 LED lamps have high light efficiency
C...[Details]
The most important components of new energy electric vehicles are power batteries, electric motors and energy conversion control systems. The power battery must achieve high performance such as fas...[Details]
This article focuses on closing the feedback loop of an isolated power supply using a TL431 shunt regulator. The article discusses a method to extend the bandwidth of the power supply control loop ...[Details]
Today's automotive application developers face numerous design challenges as modern cars add more electronic functionality, while the need for lower power consumption and smaller printed circuit bo...[Details]
Medical Electronics
京公网安备 11010802033920号
EEWORLD
