EEWORLDEEWORLDEEWORLD

Part Number

Search

3VC75H25FS-10.000M

Description
CMOS/TTL Output Clock Oscillator, 10MHz Nom, LEADLESS, CERAMIC PACKAGE-6
CategoryPassive components    oscillator   
File Size78KB,1 Pages
ManufacturerPletronics
Download Datasheet Parametric View All

3VC75H25FS-10.000M Overview

CMOS/TTL Output Clock Oscillator, 10MHz Nom, LEADLESS, CERAMIC PACKAGE-6

3VC75H25FS-10.000M Parametric

Parameter NameAttribute value
MakerPletronics
Reach Compliance Codecompliant
Other featuresENABLE/DISABLE FUNCTION; TRAY; TAPE AND REEL
Maximum control voltage3.3 V
Minimum control voltage
maximum descent time5 ns
Frequency Adjustment - MechanicalNO
Frequency offset/pull rate90 ppm
frequency stability25%
linearity10%
Manufacturer's serial numberVC7
Installation featuresSURFACE MOUNT
Nominal operating frequency10 MHz
Maximum operating temperature85 °C
Minimum operating temperature-40 °C
Oscillator typeCMOS/TTL
Output load15 pF
physical size7.0mm x 5.0mm x 1.9mm
longest rise time5 ns
Maximum supply voltage3.465 V
Minimum supply voltage3.135 V
Nominal supply voltage3.3 V
surface mountYES
Base Number Matches1
Pl tronics, Inc.
.
19013 36th Ave. W, Suite H Lynnwood, WA 98036 USA
Manufacturer of High Quality Frequency Control Products
VC7 VCXO Series
6 Pad Leadless Ceramic Surface Mount Voltage Controlled Xtal Oscillator
CMOS/ TTL Compatible with Enable/Disable
Standard Specifications
Overall Frequency Stability
Operating Temperature Range
Supply Voltage (Vcc)
Output Load
Control Voltage Range (CVR)
Pullablity over CVR
Linearity
Enable/Disable Option (E/D)
± 25, 50 PPM over Operating Temperature Range
0 to +70° C is standard, but can be extended to
-
40 to +85°C for certain frequencies
5.0 volts and 3.3 volts available, .01
μF
bypass cap recommended
Standard load is 15pF maximum, see Test Circuit 9 (consult factory for
heavier
loads)
0.5 to 4.5 volts for 5.0 volt Supply; 0.0 to 3.3 volts for 3.3 volt Supply
± 90 PPM. Consult factory for other values.
± 10% (Consult factory for ± 5%)
Output enabled when Pin #2 is open or at Logic “1”; Output disabled when Pin #2 is at Logic “0”.
Supply Current
Icc (mA)
Typical
Maximum
Rise and Fall Time
Tr & Tf (nS)
Typical
Maximum
8.000 MHz
70.000 MHz
Frequency Range
(MHz)
8.000 – 20.000
20.001 – 30.000
30.001 – 70.000
10
15
3.5
20
25
3.0
25
30
3.0
Part Numbering Guide
5.0
4.5
4.0
Portions of the part number that appear after the frequency may not be marked on part (C of C provided)
3 VC75H 25 B S - 10.0M - XXX
(Internal Code or blank)
Packaging
Tray or
16mm tape
8mm pitch
Supply Voltage
Blank= 5.0 volts ±5%
Model
3= 3.3 volts ±5%
VC74H = E/D on 5
VC75H = E/D on 2
Frequency Stability
25: ± 25 PPM
50: ± 50 PPM
00: ± 100 PPM
Frequency in MHz
Frequency Deviation (Pullability) over CVR
S: ± 90 PPM
Operating Temperature Range
B: 0 to +70
°
C
F: -40 to +85
°
C
Consult factory for available frequencies and specs. Not all options available for all frequencies. A special part number may be assigned.
Frequency Stability is inclusive of frequency shifts due to calibration, temperature, supply voltage, shock, vibration and load
Mechanical: inches (mm)
not to scale
Solder Pads
0.200 (5.08)
Due to part size and factory abilities, part marking may vary from lot to lot and may contain our part number or an internal code.
0.276 (7.0 ± .15)
0.197
(5.0 ± .15)
4
3
0.200 (5.08)
0.075 (1.9)
MAX
0.055
(1.4)
5
2
6
1
0.024
(0.60)
0.004 (0.10)
6
5
4
0 .087 (2.2)
0.050 (1.27)
.01
m
F
bypass
capacitor
1
2
3
0 .079 (2.0)
VC75H
PIN
1
2
3
4
5
6
SIGNAL
Vcon
E/D
GND
OUT
N.C.
Vcc
VC74H
PIN
1
2
3
4
5
6
SIGNAL
Vcon
N.C.
GND
OUT
E/D
Vcc
0 .055
(1.4)
For Best Performance,
Do NOT allow any traces other
than ground under oscillators
(Even in buried layers)
Dec 2006
Pl tronics, Inc.
(425) 776 -1880, Fax: (425) 776-2760, ple-sales@pletronics.com, www.pletronics.com
25
I wrote a software but I can't beat you guys
[i=s]This post was last edited by wangfuchong on 2014-6-19 18:03[/i] I wrote a small software, but it should not be considered malicious. It just helps to view the page, automatically update the page,...
wangfuchong Talking
About the design of frequency meter for the 2015 National Competition
Could any kind-hearted friend send me some design solutions for the 2015 national frequency meter problem for reference?...
如霜 Power technology
How to call C++ functions in C
I want to call functions in C++ module from C module. At present, when my C++ module does not use C++ library functions, I can call normally, such as: pro.cpp void pro(void) { printf("test"); } I use ...
lijie7905 Embedded System
Add header file in Keil
The header file in Keil is very important. For 51 single-chip microcomputers, reg51.h, reg52.h or AT89x51.h are often used. I am a novice in single-chip C language and I don't know how to use Keil. Th...
lzcqust MCU
Can software simulation of msp430 be performed in CCS?
I don't have a development board. Can I do software simulation of msp430 in CCS? Just like debugging 51 in Keil. If so, how can I set it up?...
Amos_Shun Microcontroller MCU
Dr. Dot Micro Quadcopter...Schematic Diagram and PCB Design
The completion status of Dr. Dot's micro quadcopter on November 3, 2011: 1. Motor control of Dr. Dot's micro quadcopter circuit diagram 2. Sensor of Dr. Dot's micro quadcopter circuit diagram 3. 2.4G ...
圆点博士 DIY/Open Source Hardware

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 497  774  202  768  1789  10  16  5  37  4 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号