of "●Precautions" for more information on the minimum applicable
load.
Ratings
Model
D2S-10
models
D2S-5
models
D2S-01
models
Item
Rated voltage
250 VAC
125 VAC
250 VAC
125 VAC
30 VDC
Resistive load
10.1 A
5A
3A
0.1 A
0.1 A
Characteristics
Item
Permissible operating speed
Permissible
operating
frequency
Mechanical
Electrical
Model
D2S-10 models
D2S-5 models
D2S-01 models
0.1 mm to 1 m/s (for pin plunger models)
400 operations/min
60 operations/min
100 MΩ min. (at 500 VDC with insulation tester)
OF 1.47 N models
OF 0.49 N models
-
30mΩ max.
50 mΩ max.
1,000 VAC 50/60 Hz 1 min
1,500 VAC 50/60 Hz 1 min
1,500 VAC 50/60 Hz 1 min
10 to 55 Hz, 1.5 mm double amplitude
OF 1.47 N models
OF 0.49 N models
OF 1.47 N models
OF 0.49 models
1,000 m/s
2
{approx. 100G} max.
500 m/s
2
{approx. 50G} max.
300 m/s
2
{approx. 30G} max.
200 m/s
2
{approx. 20G} max.
10,000,000 operations min.
(60 operations/min)
50,000 operations min.
(30 operations/min)
30,000,000 operations min.
(60 operations/min)
200,000 operations min.
(30 operations/min)
IEC IP40
-25°C to
+85°C
(at ambient humidity of 60% max.)
(with no icing or condensation)
85% max. (for
+5°C
to
+35°C)
Approx. 1.6 g (pin plunger models)
50 mΩ max.
100 mΩ max.
Insulation resistance
Contact resistance
(initial value)
Note. The above rating values apply under the
following test conditions.
(1) Ambient temperature: 20±2°C
(2) Ambient humidity: 65±5%
(3) Operating frequency: 30 operations/min
Between terminals of the same
polarity
Dielectric
strength * 1
Between current-carrying metal
parts and ground
Between each terminals and
non-current-carrying metal parts
Vibration
resistance * 2
Malfunction
Durability
Shock
resistance
Malfunction * 2
Mechanical
Durability * 3
Electrical
Approved Safety
Standards
The items shown in the "List
of Models"
are not standard approved models.
Consult your OMRON sales
representative for specific models with
standard approvals.
UL (UL1054)/CSA(CSA C22.2 No.55)
Rated
voltage
Model
D2S-10
-
10.1 A
-
D2S-5
5A
3A
-
D2S-01
0.1 A
-
0.1 A
Degree of protection
Ambient operating temperature
Ambient operating humidity
Weight
125 VAC
250 V
30 VDC
Note. The data given above are initial values.
*1. The values for dielectric strength shown are for models with a Separator (refer to "Micro
Switch
Common Accessories").
*2. The values are at Free Position and Total Travel Position values for pin plunger, and Total Travel
Position value for lever.
Close or open circuit of the contact is 1ms max.
*3. For testing conditions, consult your OMRON sales representative.
2
D2S
Terminals/Appearances
(Unit: mm)
●Solder
terminals
3.3
±0.1
2
7.3
8.8
±0.2
9.5
±0.1
16.1
±0.2
1.6
3.2
0.5
6.4
±0.2
5.15
1.85
8.8
±0.2
9.5
±0.1
16.1
±0.2
0.8
1.2
6.4
±0.2
0.5
1.3
Subminiature Basic Switch
Mounting Holes
(Unit: mm)
2-2.4 dia. mounting holes or
M2.3 screw holes
●Self-clinching
PCB terminals
3.3
±0.1
2
1.8
±0.1
3.9
9.5
±0.1
3-1.6 dia.holes
5.15
1.85
<PCB Mounting Dimensions (Reference)>
3-1.35
1.5 dia.
D
2
S
8.8
±0.2
16.1
±0.2
PCB's thickness t
1.6mm
Dimensions
(Unit: mm)
and Operating Characteristics
The following figures show models with self-clinching PCB terminals. For the solder terminals, refer to "Terminals/Appearances".
The
@
is replaced with the code for the terminal that you need. See the "List
of Models"
for available combinations of models.
●Pin
plunger
D2S-10@
D2S-5@
D2S-5-F@
D2S-01@
D2S-01-F@
5.3
A
2.35
±0.05
dia.
7.5
±0.1
1.8
2.35
±0.05
dia.
PT
3.6
Model
Operating
characteristics
1.8
±0.1
7
2
7.7
OP
D2S-10@
D2S-5@
D2S-01@
D2S-5-F@
D2S-01-F@
3.3
±0.1
3.9
Operating Force
Releasing Force
OF
RF
Max. 1.47 N {150 gf} 0.49 N {50 gf}
Min. 0.25 N {25 gf} 0.04 N {4 gf}
0.7 mm
0.4 mm
0.1 mm
8.4±0.25 mm
0.07
2.5
±0.07
dia.
9.5
±0.1
16.1
±0.2
0.5
1.3
6.4
±0.2
Pretravel
PT Max.
Overtravel
OT Min.
Movement Differential MD Max.
Operating Position
OP
19.8
±0.2
●Hinge
lever
D2S-10L@
D2S-5L@
D2S-5L-F@
D2S-01L@
D2S-01L-F@
t 0.3 *
14.5
A
2.35
±0.05
dia.
3.6
Model
FP
2.35
±0.05
dia.
7
2
7.7
OP
1.8
±0.1
Operating
characteristics
Operating Force
Releasing Force
OF
RF
D2S-10L@
D2S-5L@
D2S-01L@
D2S-5L-F@
D2S-01L-F@
0.18 N {18 gf}
0.02 N {2 gf}
3.3
±0.1
3.9
Max. 0.49 N {50 gf}
Min. 0.06 N {6 gf}
Overtravel
OT Min.
Movement Differential MD Max.
0.5
1.3
1.0 mm
0.8 mm
13.6 mm
9.4±0.8mm
0.07
2.5
±0.07
dia.
9.5
±0.1
16.1
±0.2
* Stainless-steel lever
6.4
±0.2
Free Position
Operating Position
FP Max.
OP
19.8
±0.2
●Simulated
roller lever
D2S-10L13@
D2S-5L13@
D2S-5L13-F@
D2S-01L13@
D2S-01L13-F@
15.8
t 0.3 *
A
R1.3
3.6
2.35
±0.05
dia.
FP
Operating
characteristics
Operating Force
Releasing Force
Model D2S-10L13@
D2S-5L13@
D2S-01L13@
OF Max.
RF Min.
0.49 N {50 gf}
0.06 N {6 gf}
D2S-5L13-F@
D2S-01L13-F@
0.18 N {18 gf}
0.02 N {2 gf}
2.35
±0.05
dia.
OP
7
2
7.7
3.3
±0.1
3.9
0.07
2.5
±0.07
dia.
9.5
±0.1
16.1
±0.2
1.8
±0.1
Overtravel
OT Min.
Movement Differential MD Max.
Free Position
Operating Position
FP Max.
OP
1.0 mm
0.8 mm
15.5 mm
11.4±0.8 mm
0.5
1.3
*Stainless-steel lever
6.4
±0.2
19.8
±0.2
Note 1. Unless otherwise specified, a tolerance of
±0.4
mm applies to all dimensions.
Note 2. The operating characteristics are for operation in the A direction ( ).
3
D2S
●Hinge
roller lever
D2S-10L2@
D2S-5L2@
D2S-5L2-F@
D2S-01L2@
D2S-01L2-F@
14.5
t=0.3 *1
2.35
±0.05
dia.
FP
OP
2.35
±0.05
dia.
7
2
7.7
3.3
±0.1
3.9
1.8
±0.1
A
4.8x3.2 *2 dia.
Subminiature Basic Switch
Model
Operating
characteristics
Operating Force
Releasing Force
OF Max.
RF Min.
D2S-10L2@
D2S-5L2@
D2S-01L2@
0.49 N {50 gf}
0.06 N {6 gf}
D2S-5L2-F@
D2S-01L2-F@
0.18 N {18 gf}
0.02 N {2 gf}
Overtravel
OT Min.
Movement Differential MD Max.
Free Position
Operating Position
FP Max.
OP
1.0 mm
0.8 mm
19.3 mm
15.1±0.8 mm
D
2
S
0.07
2.5
±0.07
dia.
9.5
±0.1
16.1
±0.2
0.5
1.3
6.4
±0.2
*1. Stainless-steel lever
*2. Polyacetal resin roller
19.8
±0.2
Note 1. Unless otherwise specified, a tolerance of
±0.4
mm applies to all dimensions.
Note 2. The operating characteristics are for operation in the A direction ( ).
Precautions
★
Please refer to "Basic Switches Common Precautions" for correct use.
Cautions
●Soldering
When using automatic soldering baths, we recommend soldering
at 260±5°C within 5 seconds. Make sure that the liquid surface
of the solder does not flow over the edge of the board.
When soldering terminals manually, complete the soldering at
the iron tip temperature between 350 to 400°C within 3 seconds,
and do not apply any external force for 1 minute after soldering.
When applying solder, keep the solder away from the case of the
Switch and do not allow solder or flux to flow into the case.
Correct Use
●Mounting
Use M2.3 mounting screw with plane washers or spring washers
to securely mount the Switch. Tighten the screws to a torque of
0.23 to 0.26 N·m {2.3 to 2.7 kgf·cm}.
●Using
Micro Loads
Using a model for ordinary loads to open or close the contact of
a micro load circuit may result in faulty contact. Use models that
operate in the following range. However, even when using micro
load models within the following operating range, if inrush
current occurs when the contact is opened or closed, it may
increase the contact wear and so decrease durability. Therefore,
insert a contact protection circuit where necessary. The N-level
reference value applies for the minimum applicable load. This
value indicates the malfunction reference level for the reliability
level of 60% (λ
60
).
(JIS C5003)
The equation,
λ
60
=0.5×10
-6
/operations indicates that the
1
estimated malfunction rate is less than
2,000,000
operations with
a reliability level of 60%.
Voltage (V)
0.16 mA
26 mA
100 mA
30
24
Normal load
type
Operating
range
D2S-5
D2S-10
Micro load type
Operating range
D2S-01
12
5
0
0.1
1 mA
1
10
100 mA 160 mA
100
1,000
Current (mA)
4
D2S
Subminiature Basic Switch
D
2
S
•
Application examples provided in this document are for reference only. In actual applications, confirm equipment functions and safety before using the product.
•
Consult your OMRON representative before using the product under conditions which are not described in the manual or applying the product to nuclear control systems, railroad
systems, aviation systems, vehicles, combustion systems, medical equipment, amusement machines, safety equipment, and other systems or equipment that may have a serious
influence on lives and property if used improperly. Make sure that the ratings and performance characteristics of the product provide a margin of safety for the system or
equipment, and be sure to provide the system or equipment with double safety mechanisms.
Note: Do not use this document to operate the Unit.
[font=微软雅黑][size=4][b][url=https://e2echina.ti.com/blogs_/b/thinkinnovative/archive/2018/01/31/52804]Magnetic sensors: The giant behind future sensing technology[/url][/b] In the automotive world, mag...
Share switching power supply design video materials, EMI design, PCB wiring, heat source management, flyback design, loop compensation, heat source management, etc., to help you become a power enginee...
A: I have a few questions to ask: 1. Can we just turn off the modules we don’t use in myimx6_defconfig? Do we need to modify other ones? 2. How to configure the second network port? 3. The rootfs is a...
I use C8051F as SPI master device and LM3S3739 as SPI slave device.
1. SPI clock is 4MHz, data width is 8bit, SPI adopts Freescale format, SPO=0, SPH=0;
2. In the program, CM3 allows SPI reception and...
EtherCAT (Ethernet for Control Automation Technology) is a real-time industrial fieldbus communication protocol based on an Ethernet-based development framework. EtherCAT is one of the fastest indu...[Details]
According to foreign media reports, secondary battery materials company POSCO Future M announced that it has successfully developed two experimental (prototype) positive electrode materials for the...[Details]
This paper proposes a temperature real-time transmission and display solution based on LED optical data transmission, with Jingwei Yager low-power FPGA HR (Yellow River) series as the main controll...[Details]
1 Source of creativity
With the further development of electronic technology, electronic pets have gradually entered people's family life. At present, there are two main categories of relative...[Details]
introduction
Sonar imaging is of great significance in marine resource development and defense. Its long range, intuitive display of the observed area, and target identification make it widely...[Details]
With the development of science, the use of variable frequency technology is becoming more and more widespread, and it is used in both industrial equipment and household appliances. Inverter air co...[Details]
There are basically three causes of spontaneous combustion of electric vehicles: The first is that the battery components are punctured or suffer fatal damage due to a collision accident, and part ...[Details]
With the increasing number of new energy vehicles on the road, the deployment of supporting facilities for these vehicles has accelerated, and new energy vehicles have gradually entered the vision ...[Details]
The MCX E series is the most reliability- and safety-focused series in NXP's extensive MCX product portfolio.
With the launch of this series, NXP has further enriched its 5V-compatible MCU pr...[Details]
In the period after the switching power supply achieved the "20 kHz" revolution in the 1970s, although improvements and enhancements were made in circuit technology, the development level of the se...[Details]
On August 21, it was reported that Intel's new generation of AI chip Jaguar Shores was recently exposed for the first time.
According to photos shared by Andreas Schilling, the Jaguar Shores t...[Details]
As a pioneer in the new smart home concept, robot vacuums have captured a significant market share. Robot vacuums, also known as automatic sweepers, smart vacuums, or robot vacuums, are smart home ...[Details]
0 Introduction
Portable terminals integrate a computer and display screen into a single device. Due to limited space in portable devices, previous designs often used a single-chip microcompute...[Details]
Using an electronic load is like thinking of it as a resistor that dissipates the power supply's output. The most straightforward mode is the CR constant resistance mode. In this mode, by setting a...[Details]
As my country's industrialization continues to improve, environmental pollution is also facing tremendous pressure. In recent years, national environmental protection policies have become increasin...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
