This applicator assembly must be used with Pneudraulic Tool 59809-2. The applicator assembly and pneudraulic tool are no longer available for new applications,
‡
however the fixtures can be used with existing applications.
The tooling assembly must be used with Manual Arbor Frame Assembly 58024-1 (408-6923).
Figure 1
1. INTRODUCTION
Mass Termination Assembly (MTA) .100 Connector-
Holding Fixtures listed in Figure 1 are designed to hold
.100 MTA connectors and discrete wires in position for
termination. The fixture is used with the MTA
applicator assembly or tooling assembly (also listed in
Figure 1). The fixtures are designed for feed-through
(wires are not cut) or closed end (wires are cut). The
connectors are available with up to 28 contact
positions on 2.54-mm [.100-in.] centerline spacing.
Read these instructions and referenced material
thoroughly before using the fixture.
NOTE
Dimensions in this instruction sheet are in
millimeters [with inches in brackets]. Figures are
not drawn to scale.
Reasons for reissue of this instruction sheet are
provided in Section 7, REVISION SUMMARY.
2. DESCRIPTION
Each fixture consists of a one-piece locating plate,
housing support, front wire comb, and rear wire comb.
The polarizing tab is used to properly orient the
applicator or tooling assembly with the fixture.
3. SETUP
Select the connector according to the color code that
matches the wire size as follows:
WIRE SIZE (AWG)
28
26
24
22
CONNECTOR COLOR CODE
Green
Blue
Natural
Red
i
For information on operating the applicator or tooling
assembly, refer to the instruction sheet (indicated in
parenthesis in Figure 1) packaged with the tooling.
For latest revision and Regional Customer Service,
visit our website at
www.te.com
1
of 4
LOC B
TE Connectivity, TE connectivity (logo), and TE (logo) are trademarks. Other logos, product and/or Company names may be trademarks of their respective owners.
408-7994
Then select the connector size according to the
required number of contact positions. Refer to Figure
1 to make sure that the fixture is compatible with the
connector and method of application.
Proceed as follows:
1. Prepare the cable according to 408-9515. If using
the tooling assembly (58039-1), proceed to Section
4, otherwise continue with the following steps.
2. Determine the location for the fixture on the
harness board. Make sure space is provided for
lengths of wire between connectors. Refer to
Figure 2.
Harness Board
NOTE
The applicator assembly can be rotated 360_,
however, to avoid unnecessary motion, the fixture
should be positioned so that the least amount of
rotation of the applicator assembly is required.
i
3. Drill holes in the board for mounting the fixture.
Refer to Figure 3 for recommended board layout. If
using connector assembly for testing, cut a slot for
the post retainer assembly.
4. Attach the fixture to the board using screws,
washers, and nuts, or suitable commercially
available hardware.
5. Place wire roll at a convenient location for lacing
into the fixture.
4. TERMINATION PROCEDURE
Refer to Figure 4, and proceed as follows:
1. Spread the fixture wire combs apart, and insert
the connector, mating end first, into the center of the
receiving track. Make sure that the connector
shoulder is behind the locating plate and the
connector ribs are aligned with the slots in the
wire comb.
CAUTION
The connector must be located in the center of the
receiving track. Do NOT place more than two
connectors end to end in the fixture.
!
2. Lace a wire over the slot in the wire combs that
aligns with the applicable connector contact. Make
sure that the wire is straight, then press the wire into
the slot until it bottoms in the wire combs. Repeat
until all wires are positioned.
3. Terminate the connector according to 408-4260
(if using applicator assembly) or 408-6685 (if using
tooling assembly).
Fixture with
Connector
Wire Roll
Figure 2
Recommended Harness Board Layout
Note:
Not to scale
DIMENSION
A
40.6
[1.60]
31.8
[1.25]
B
107.95
[4.25]
90.17
[3.55]
FIXTURE
58242-3, 58242-4,
58243-3, 59845-3
58242-1, 58242-2,
58243-1, 58243-2,
58635-1, 58636-1,
59844-1, 59845-1
Fixture
Figure 3
Rev
C
2
of 4
408-7994
Connector Ribs
Aligned with Slots
in Wire Combs
Front Wire
Comb
2. If applicable, test the connector for continuity
using the post retainer assembly.
NOTE
The post retainer assembly is only included with
some fixtures. Post Retainer Assembly 310672-1 is
available as an accessory for Fixtures 59844-1,
59845-1, and 59845-3 but cannot be used if the
fixture is used with the tooling assembly (58039-1).
Connector Centered
on Fixture Receiving
Track
i
6. REPLACEMENT AND REPAIR
Customer-replaceable parts are listed in Figure 5.
A complete inventory should be stocked and
controlled to prevent lost time when replacement of
parts is necessary. Parts other than those listed should
be replaced by TE Connectivity to ensure quality and
reliability. Order replacement parts through your
representative, or call 1-800-526-5142, or send a
facsimile of your purchase order to 717-986-7605, or
write to:
CUSTOMER SERVICE (038-035)
TYCO ELECTRONICS CORPORATION
PO BOX 3608
HARRISBURG PA 17105-3608
For customer repair service, call 1-800-526-5136.
Rear Wire
Comb
Connector Shoulder
Behind Fixture
Locating Plate
Figure 4
Wires bottomed
in Wire Combs
4. Spread the fixture wire combs apart, and lift the
connector out of the fixture.
5. INSPECTING TERMINATED CONNECTOR
1. Visually inspect the connector to make sure that
USART generally has two modes: query and interrupt, but I still prefer the query method, because the interrupt method is always difficult to use and I think it is too esoteric. After struggling for se...
For more information, please see Li Ai's blog post: [url=http://blog.sina.com.cn/s/blog_475bd0960102e2fj.html]http://blog.sina.com.cn/s/blog_475bd0960102e2fj.html [/url] Oh, they also use clickbait to...
I am using a WinCE6 system. After it goes into sleep mode, it needs to be woken up by an external event. Can it be woken up by an external interrupt? If so, how can I do it? Thank you....
[i=s]This post was last edited by paulhyde on 2014-9-15 03:56[/i]Those who have solved this problem, please share your experience! What is your solution and how do you solve the problem of traffic div...
While
the solid-state battery
industry is still engaged in a long technological marathon for
the "ultimate solution" for
electric vehicles
, some companies have begun looking for mor...[Details]
On August 24th, Jin Yuzhi, CEO of Huawei's Intelligent Automotive Solutions BU, announced the first automotive application of Huawei Qiankun's unique Limera technology. This technology eliminates t...[Details]
Amidst the wave of intelligent automotive transformation, advanced driver assistance is gradually emerging from cutting-edge technology into the mainstream, becoming a new frontier of industry comp...[Details]
According to foreign media reports, secondary battery materials company POSCO Future M announced that it has successfully developed two experimental (prototype) positive electrode materials for the...[Details]
Based on a survey of more than ten intelligent robot companies, this article sorts out and analyzes the current development status of the intelligent industry and the challenges and differences it ...[Details]
This paper proposes a temperature real-time transmission and display solution based on LED optical data transmission, with Jingwei Yager low-power FPGA HR (Yellow River) series as the main controll...[Details]
Charging is a familiar process for new energy vehicles, and as a source of battery energy, charging piles are crucial. New energy vehicle charging can be divided into fast charging and slow chargin...[Details]
During daily operation of an R-type power transformer, the voltage used varies as the equipment being used adjusts. This raises the question: can the transformer change voltage at this point? The a...[Details]
The range of an electric vehicle is crucial to the driving experience, and range anxiety is a common headache when driving an electric vehicle. Although the latest electric vehicles can achieve a r...[Details]
Summer is the peak season for buying and using air conditioners. Do you pay attention to the energy efficiency of your air conditioner? Did you buy a DC inverter air conditioner? Do you know the re...[Details]
Silicon Labs (also known as "Silicon Labs"), an innovative leader in low-power wireless connectivity, will showcase its cutting-edge artificial intelligence (AI) and Internet of Things (IoT) solu...[Details]
With the development of vehicle technology, there are more types of cars. Cars are divided into hybrid, pure electric vehicles, and fuel vehicles. For hybrid cars, they are divided into plug-in hyb...[Details]
As the core of electric vehicles, batteries are concerned with vehicle use and maintenance. The operation of vehicles is guaranteed by the electricity generated by batteries. For batteries, battery...[Details]
As a core component of electric vehicles, power batteries, like batteries for other electronic products, inevitably experience degradation after a certain period of use due to their characteristics...[Details]
New energy vehicles are a trend and a hot topic in the current automotive market. Driven by enthusiastic promotion from automakers and supported by government policies, these vehicles have seen rap...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
