EEWORLDEEWORLDEEWORLD

Part Number

Search

ICS525RI07LF

Description
lvcmos user configurable clock
File Size109KB,9 Pages
ManufacturerIntegrated Circuit Systems(IDT )
Download Datasheet Compare View All

ICS525RI07LF Overview

lvcmos user configurable clock

PRELIMINARY INFORMATION
ICS525-07/08
LVCMOS User Configurable Clock
Description
The ICS525-07/08 are the most flexible way to
generate a high-quality clock output from an
inexpensive crystal or clock input at low supply
voltages. The user can configure the device to produce
nearly any output frequency from any input frequency
by grounding or floating the select pins or by driving or
hard wiring the select pins high or low. Neither
microcontroller, software, nor device programmer are
needed to set the frequency. Using Phase-Locked
Loop (PLL) techniques, the device accepts a standard
fundamental mode, inexpensive crystal to produce
output clocks up to 250 MHz. It can also produce a
highly accurate output clock from a given input clock,
keeping them frequency locked.
For similar capability with a serial interface, use the
ICS307.
This product is intended for clock generation. It has low
output jitter (variation in the output period), but input to
output skew is not defined nor guaranteed.
Features
Packaged as 28-pin SSOP (150 mil body)
Available in Pb (lead) free package
User determines the output frequency by setting all
internal dividers
Eliminates need for custom oscillators
Low voltage operation
Pull-ups on all select inputs
Input crystal frequency of 5 - 27 MHz
Input clock frequency of 2 - 50 MHz
Compensated loop bandwidth
Enhanced low frequency operation (-08 version)
Low jitter
Duty cycle of 45/55 up to 200 MHz
Operating voltage of 1.8 V to 2.5 V
Ideal for oscillator replacement
Available in commercial and industrial temperature
ranges
Block Diagram
2
PD
X1/ICLK
Crystal
or clock
input
Crystal
Oscillator
X2
Reference
Divider
Phase
Comparator,
Charge
Pump,
and
Loop Filter
VCO
VCO
Divider
Divider
VDD
REF
VCO
Output
Divider
CLK
Optional crystal
capacitors
Optional crystal
capacitors
2
2
R
Configuration Pins
R
Configuration Pins
V Configuration Pins
V Configuration Pins
GND
GND
S Configuration Pins
S Configuration Pins
MDS 525-07/08 A
Integrated Circuit Systems, Inc.
1
525 Race Street, San Jose, CA 95126
Revision 101105
tel (408) 297-1201
www.icst.com

ICS525RI07LF Related Products

ICS525RI07LF ICS525RI-07T ICS525RI-08T ICS525RI08LF ICS525RI-07LF ICS525R-I07 ICS525RI-07 ICS525RI-08 ICS525RI-08LF
Description lvcmos user configurable clock lvcmos user configurable clock lvcmos user configurable clock lvcmos user configurable clock lvcmos user configurable clock lvcmos user configurable clock lvcmos user configurable clock lvcmos user configurable clock lvcmos user configurable clock
[Play with ADuCM360] Self-made ADuCM360 ADC initialization program-----The chip is provided by VOCO_2000 netizen
The measured voltage is basically normal, and the ADC can work normally in continuous mode. 1. Remove all the "ADI_" in the header file of ADI's ADUCM360. I find it annoying. 2. I used the functions p...
dontium ADI Reference Circuit
Please recommend a nand writer for 6410 irom boot mode
As the title says: Please recommend a 6410 irom boot mode nand writer. It seems to be a dedicated writer, but I can't find it online. Thanks for the recommendation...
ljh_gyy Embedded System
CC4038------Three serial adders
This article introduces the relevant knowledge of CC4038 in detail. Three serial adders (negative logic)...
rain Analog electronics
Show the process of WEBENCH design + solar cell buck circuit design
[color=#3e3a39][font=微软雅黑]Using WEBENCH to design a solar cell step-down circuit, the output current I chose at the beginning was too small, 0.1A, so there was no design plan. Later, after changing th...
hanskying666 Analogue and Mixed Signal
Quartus II cannot simulate
[color=#666666][backcolor=rgb(222, 240, 251)]I installed Quartus II 13.1, and the file compilation is fine. But when simulating, I found that it does not move forward. [/backcolor][/color][p=20, null,...
chenbingjy FPGA/CPLD
Difference between LOG_printf() and printf() in DSP
During development, it is usually necessary to use printf() to display the current status. However, printf() is a very time-consuming function and is not real-time. Because the DSP needs to analyze th...
fish001 DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1105  1503  985  1654  583  23  31  20  34  12 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号