The AMS1084 series of adjustable and fixed voltage regulators are designed to provide 5A output current and to operate
down to 1V input-to-output differential. The dropout voltage of the device is guaranteed maximum 1.5V at maximum output
current, decreasing at lower load currents.
On-chip trimming adjusts the reference voltage to 1%. Current limit is also trimmed, minimizing the stress under overload
conditions on both the regulator and power source circuitry.
The AMS1084 devices are pin compatible with older three-terminal regulators and are offered in 3 lead TO-220 package, 3
and 2 lead TO-263 (Plastic DD) and TO-252 (D PAK) package.
ORDERING INFORMATION:
PACKAGE TYPE
3 LEAD TO-220
AMS1084CT
AMS1084CT-1.5
AMS1084CT-2.5
AMS1084CT-2.85
AMS1084CT-3.0
AMS1084CT-3.3
AMS1084CT-3.5
AMS1084CT-5.0
2&3 LEAD TO-263
AMS1084CM
AMS1084CM-1.5
AMS1084CM-2.5
AMS1084CM-2.85
AMS1084CM-3.0
AMS1084CM-3.3
AMS1084CM-3.5
AMS1084CM-5.0
TO-252
AMS1084CD
AMS1084CD-1.5
AMS1084CD-2.5
AMS1084CD-2.85
AMS1084CD-3.0
AMS1084CD-3.3
AMS1084CD-3.5
AMS1084CD-5.0
OPERATING JUNCTION
TEMPERATURE RANGE
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
0 to 125° C
TO-220 FRONT VIEW
TO-252 FRONT VIEW
PIN CONNECTIONS
FIXED VERSION
1- Ground
2- V
OUT
3- V
IN
ADJUSTABLE VERSION
1- Adjust
2- V
OUT
3- V
IN
TAB IS
OUTPUT
3
2
1
TAB IS
OUTPUT
3
2
1
2L TO-263 FRONT VIEW
3
2
1
TAB IS
OUTPUT
3L TO-263 FRONT VIEW
3
2
1
TAB IS
OUTPUT
Advanced Monolithic Systems, Inc.
www.advanced-monolithic.com
Phone (925) 443-0722
Fax (925) 443-0723
AMS1084
ABSOLUTE MAXIMUM RATINGS
(Note 1)
Power Dissipation
Input Voltage
Operating Junction Temperature
Control Section
Power Transistor
Storage temperature
Internally limited
15V
0°C to 125°C
0°C to 150°C
- 65°C to +150°C
Soldering information
Lead Temperature (25 sec)
Thermal Resistance
TO-220 package
TO-263 package
TO-252 package
265°C
ϕ
JA
= 50°C/W
ϕ
JA
= 30°C/W *
ϕ
JA
= 100°C/W
* With package soldering to 0.5in
2
copper area over backside
ground plane or internal power plane
ϕ
JA
can vary from
20°C/W to
>40°C/W
depending on mounting technique.
ELECTRICAL CHARACTERISTICS
Electrical Characteristics at I
OUT
= 0 mA, and T
J
= +25°C unless otherwise specified.
Parameter
Reference Voltage
(Note 2)
Output Voltage
(Note 2)
Device
AMS1084
AMS1084-1.5
AMS1084-2.5
AMS1084-2.85
AMS1084-3.0
AMS1084-3.3
AMS1084-3.5
AMS1084-5.0
Conditions
I
OUT
= 10 mA
10mA
≤
I
OUT
≤
5A, 1.5V≤ (V
IN
- V
OUT
)
≤
12V
0
≤
I
OUT
≤
5A , 3V
≤
V
IN
≤
12V
0
≤
I
OUT
≤
5A , 4V
≤
V
IN
≤
12V
0
≤
I
OUT
≤
5A , 4.35V≤ V
IN
≤
12V
0
≤
I
OUT
≤
5A , 4.5V
≤
V
IN
≤
12V
0
≤
I
OUT
≤
5A , 4.75V
≤
V
IN
≤
12V
0
≤
I
OUT
≤
5A, 5V
≤
V
IN
≤
12V
0
≤
I
OUT
≤
5A , 6.5V
≤
V
IN
≤
12V
I
LOAD
= 10 mA , 1.5V≤ (V
IN
- V
OUT
)
≤
12V
(V
IN
- V
OUT
) =3V, 10mA
≤
I
OUT
≤
5A
V
IN
= 5V, 0
≤
I
OUT
≤
5A
V
IN
= 5V, 0
≤
I
OUT
≤
5A
V
IN
= 5V, 0
≤
I
OUT
≤
5A
V
IN
= 5V, 0
≤
I
OUT
≤
5A
V
IN
= 5V, 0
≤
I
OUT
≤
5A
V
IN
= 5.25V, 0
≤
I
OUT
≤
5A
V
IN
= 8V, 0
≤
I
OUT
≤
5A
∆V
OUT
,
∆V
REF
= 1%, I
OUT
= 5 A (Note 4)
Min
1.238
1.225
1.485
1.470
2.475
2.450
2.82
2.79
2.970
2.940
3.267
3.235
3.465
3.430
4.950
4.900
Typ
1.250
1.250
1.500
1.500
2.500
2.500
2.850
2.850
3.000
3.000
3.300
3.300
3.500
3.500
5.000
5.000
0.3
0.6
0.1
0.2
3
6
3
6
3
6
3
6
3
7
3
6
5
10
1.3
Max
1.262
1.270
1.515
1.530
2.525
2.550
2.88
2.91
3.300
3.360
3.333
3.365
3.535
3.570
5.050
5.100
6
10
0.3
0.4
12
20
12
20
12
20
12
20
15
25
15
25
20
35
1.5
Units
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
mV
mV
%
%
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
mV
V
Line Regulation
Load Regulation
(Notes 2, 3)
AMS1084/-1.5/-2.5/-
2.85/ -3.0/-3.3/-3.5/-5.0
AMS1084
AMS1084-1.5
AMS1084-2.5
AMS1084-2.85
AMS1084-3.0
AMS1084-3.3
AMS1084-3.5
AMS1084-5.0
Dropout Voltage
(V
IN
-
V
OUT
)
AMS1084/-1.5/-2.5/-
2.85/ -3.0/-3.3/-3.5/-5.0
Advanced Monolithic Systems, Inc.
www.advanced-monolithic.com
Phone (925) 443-0722
Fax (925) 443-0723
AMS1084
ELECTRICAL CHARACTERISTICS
Electrical Characteristics at I
OUT
= 0 mA, and T
J
= +25°C unless otherwise specified.
Parameter
Current Limit
Minimum Load
Current
Quiescent Current
Ripple Rejection
Device
AMS1084/-1.5/-2.5/-
2.85/ -3.0/-3.3/-3.5/-5.0
AMS1084
AMS1084/-1.5/-2.5/-
2.85/ -3.0/-3.3/-3.5/-5.0
AMS1084
AMS1084-1.5
AMS1084-2.5
AMS1084-2.85
AMS1084-3.0
AMS1084-3.3
AMS1084-3.5
AMS1084-5.0
Conditions
(V
IN
- V
OUT
) = 5V
(V
IN
- V
OUT
) = 12V (Note 5)
V
IN
≤
12V
Min
5.00
Typ
6.00
5
5
Max
7.00
10
10
Units
A
mA
mA
dB
dB
dB
dB
dB
dB
dB
dB
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 5A,
(V
IN
-V
OUT
) = 3V, C
ADJ
=25µF
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 5A,
V
IN
= 4.5V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 5A,
V
IN
= 5.5V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 5A,
V
IN
= 6V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 5A
V
IN
= 6V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 5A
V
IN
= 6.3V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 5A
V
IN
= 6.5V
f =120Hz , C
OUT
= 25µF Tantalum, I
OUT
= 5A
V
IN
= 8V
T
A
= 25°C, 30ms pulse
10mA
≤
I
OUT
≤
5A , 1.5V≤ (V
IN
- V
OUT
)
≤
12V
10mA
≤
I
OUT
≤
5A , 1.5V≤ (V
IN
- V
OUT
)
≤
12V
60
60
60
60
60
60
60
60
75
72
72
72
72
72
72
68
0.008
55
120
0.2
0.5
5
0.04
Thermal Regulation
Adjust Pin Current
Adjust Pin Current
Change
Temperature Stability
Long Term Stability
RMS Output Noise
(% of V
OUT
)
Thermal Resistance
Junction-to-Case
AMS1084
AMS1084
AMS1084
%W
µA
µA
µA
%
T
A
=125°C, 1000Hrs
T
A
= 25°C , 10Hz
≤
f
≤
10kHz
M Package: Control Circuitry/ Power Transistor
T Package: Control Circuitry/ Power Transistor
0.3
0.003
1
%
%
1.5/4.0
1.5/4.0
°C/W
°C/W
Parameters identified with
boldface type
apply over the full operating temperature range.
Note 1:
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. For guaranteed specifications and test conditions, see the
Electrical Characteristics
.
The guaranteed specifications apply only for the test conditions listed.
Note 2:
Line and Load regulation are guaranteed up to the maximum power dissipation of 15W. Power dissipation is determined by the input/output
differential and the output current. Guaranteed maximum power dissipation will not be available over the full input/output range.
Note 3:
See thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant junction
temperature by low duty cycle pulse testing. Load regulation is measured at the output lead ~1/8” from the package.
Note 4:
Dropout voltage is specified over the full output current range of the device.
Note 5:
Minimum load current is defined as the minimum output current required to maintain regulation. When (V
IN
- V
OUT
) = 12V the device is guaranteed
to regulate if the output current is greater than 10mA.
Advanced Monolithic Systems, Inc.
www.advanced-monolithic.com
Phone (925) 443-0722
Fax (925) 443-0723
AMS1084
APPLICATION HINTS
The AMS1084 series of adjustable and fixed regulators are easy to
use and have all the protection features expected in high
performance voltage regulators: short circuit protection and
thermal shut-down.
Pin compatible with older three terminal adjustable regulators,
these devices offer the advantage of a lower dropout voltage, more
precise reference tolerance and improved reference stability with
temperature.
Stability
The circuit design used in the AMS1084 series requires the use of
an output capacitor as part of the device frequency compensation.
The addition of
150
µF
aluminum electrolytic or a 22µF solid
tantalum on the output will ensure stability for all operating
conditions.
When the adjustment terminal is bypassed with a capacitor to
improve the ripple rejection, the requirement for an output
capacitor increases. The value of 22µF tantalum or
150
µF
aluminum covers all cases of bypassing the adjustment terminal.
Without bypassing the adjustment terminal smaller capacitors can
be used with equally good results.
To ensure good transient response with heavy load current
changes capacitor values on the order of 100µF are used in the
output of many regulators. To further improve stability and
transient response of these devices larger values of output
capacitor can be used.
Protection Diodes
Unlike older regulators, the AMS1084 family does not need any
protection diodes between the adjustment pin and the output and
from the output to the input to prevent over-stressing the die.
Internal resistors are limiting the internal current paths on the
AMS1084 adjustment pin, therefore even with capacitors on the
adjustment pin no protection diode is needed to ensure device
safety under short-circuit conditions.
Diodes between the input and output are not usually needed.
Microsecond surge currents of 50A to 100A can be handled by the
internal diode between the input and output pins of the device. In
normal operations it is difficult to get those values of surge
currents even with the use of large output capacitances. If high
value output capacitors are used, such as 1000µF to 5000µF and
the input pin is instantaneously shorted to ground, damage can
occur. A diode from output to input is recommended, when a
crowbar circuit at the input of the AMS1084 is used. Normal
power supply cycling or even plugging and unplugging in the
system will not generate current large enough to do any damage.
The adjustment pin can be driven on a transient basis
±25V,
with
respect to the output without any device degradation. As with any
IC regulator, none the protection circuitry will be functional and
the internal transistors will break down if the maximum input to
output voltage differential is exceeded.
D1
V
IN
AMS1084
IN
OUT
ADJ
C
ADJ
10µF
V
OUT
R
1
R
2
+
C
OUT
150µF
Overload Recovery
When the power is first turned on, as the input voltage rises, the
output follows the input, permitting the regulator to start up into
heavy loads. During the start-up, as the input voltage is rising, the
input-to-output voltage differential remains small, allowing the
regulator to supply large output currents. A problem can occur
with a heavy output load when the input voltage is high and the
output voltage is low, when the removal of an output short will not
permit the output voltage to recover. The load line for such a load
may intersect two points on the output current curve. In this case,
there are two stable output operating points for the regulator. With
this double intersection, the power supply may need to be cycled
down to zero and brought up again to make the output recover.
Ripple Rejection
The ripple rejection values are measured with the adjustment pin
bypassed. The impedance of the adjust pin capacitor at the ripple
frequency should be less than the value of R1 (normally 100Ω
to120Ω) for a proper bypassing and ripple rejection approaching
the values shown. The size of the required adjust pin capacitor is a
function of the input ripple frequency. If R1=100Ω at 120Hz the
adjust pin capacitor should be 25µF. At 10kHz only 0.22µF is
needed.
The ripple rejection will be a function of output voltage, in circuits
without an adjust pin bypass capacitor. The output ripple will
increase directly as a ratio of the output voltage to the reference
voltage (V
OUT
/ V
REF
).
Output Voltage
The AMS1084 series develops a 1.25V reference voltage between
the output and the adjust terminal. Placing a resistor between these
two terminals causes a constant current to flow through R1 and
down through R2 to set the overall output voltage.
Advanced Monolithic Systems, Inc.
www.advanced-monolithic.com
Phone (925) 443-0722
Fax (925) 443-0723
AMS1084
APPLICATION HINTS
This current is normally the specified minimum load current of
10mA. Because I
ADJ
is very small and constant it represents a
small error and it can usually be ignored.
Connected as shown, R
P is
not multiplied by the divider ratio.
Using 16-gauge wire the parasitic line resistance is about 0.004Ω
per foot, translating to 4mV/ft at 1A load current. It is important
to keep the positive lead between regulator and load as short as
possible and use large wire or PC board traces.
Thermal Considerations
The AMS1084 series have internal power and thermal limiting
circuitry designed to protect the device under overload conditions.
However maximum junction temperature ratings should not be
exceeded under continuous normal load conditions. Careful
consideration must be given to all sources of thermal resistance
from junction to ambient, including junction-to-case, case-to-heat
sink interface and heat sink resistance itself. To ensure safe
operating temperatures and reflect more accurately the device
temperature, new thermal resistance specifications have been
developed. Unlike older regulators with a single junction-to-case
thermal resistance specification, the data section for these new
regulators provides a separate thermal resistance and maximum
junction temperature for both the Control Section and the Power
Transistor. Calculations for both temperatures under certain
conditions of ambient temperature and heat sink resistance and to
ensure that both thermal limits are met.
Junction-to-case thermal resistance is specified from the IC
junction to the bottom of the case directly below the die. This is
the lowest resistance path for the heat flow. In order to ensure the
best possible thermal flow from this area of the package to the
heat sink proper mounting is required. Thermal compound at the
case-to-heat sink interface is recommended. A thermally
conductive spacer can be used, if the case of the device must be
electrically isolated, but its added contribution to thermal
resistance has to be considered.
V
IN
AMS1084
IN
OUT
ADJ
50µA
V
OUT
V
REF
R1
R2
I
ADJ
V
OUT
= V
REF
(1+
R2/R1)+I
ADJ
R2
Figure 1. Basic Adjustable Regulator
Load Regulation
True remote load sensing it is not possible to provide, because the
AMS1084 is a three terminal device. The resistance of the wire
connecting the regulator to the load will limit the load regulation.
The data sheet specification for load regulation is measured at the
bottom of the package. Negative side sensing is a true Kelvin
connection, with the bottom of the output divider returned to the
negative side of the load.
The best load regulation is obtained when the top of the resistor
divider R1 is connected directly to the case not to the load. If R1
were connected to the load, the effective resistance between the
I recently encountered a problem when learning about FPGA FIR filters. I set a 12-bit wide low-pass filter with the following parametersHowever, after selecting the output simulation model in the seco...
My idea is to set up an IP for the 51 system and then control it through IP point-to-point serial communication. I don't know if I can set up an IP for the 51 system, so I'm posting this to ask for he...
Moderator Chip Coin issuance requirements: Monthly online time> 30 hours Monthly posts> 30 posts Some small rules for moderators: [url=https://bbs.eeworld.com.cn/thread-77551-1-1.html]https://bbs.eewo...
USB (Universal Serial Bus) is gradually developing into a standard transmission protocol. This development is undoubtedly due to the widespread use of USB interfaces in many electronic products. There...
I am a high school student. I have set up a team and am now working on a wall-climbing robot. I use a model airplane motor to make the robot stick to the wall. I would like to ask which development bo...
The rapid development of the Internet has realized high-speed information transmission and resource sharing, greatly facilitating people's lives. Embedded systems are widely used in various electr...[Details]
introduction
In the discharge process of tokamak plasma physics, the study of rupture and sawtooth is of great significance. Rupture and sawtooth exist in most tokamaks. Rupture is a notew...[Details]
The Mobile Industry Processor Interface (MIPI) Alliance is an organization responsible for promoting the standardization of software and hardware in mobile devices. It has released the D-PHY specif...[Details]
There are three types of mobile TV: one is based on analog TV broadcasting network, another is based on mobile communication network, and the other is based on digital broadcasting network. The f...[Details]
introduction
Solar cells and LED lighting are typical applications of new energy and energy-saving and efficient technologies. Solar LED lighting uses solar cells to convert solar energy...[Details]
1 Introduction
Ultrasonic waves have strong directivity, slow energy consumption, and can propagate over long distances in a medium, so they are used for distance measurement. Ultrasonic detec...[Details]
Toyohashi University of Technology demonstrated electric field coupled wireless power supply technology using life-size car tires and roads at the wireless technology exhibition "Wireless Technolog...[Details]
1. When the slip speed regulating motor is undergoing frequency conversion and energy saving transformation, the original excitation box (referred to as the speed regulating box) and the original s...[Details]
Motors are important products that convert electrical energy into mechanical energy to achieve automation, and they are widely used in industrial control, medical electronics, white a...[Details]
hint:
The number of speakers and their spacing limit the sound field of a portable stereo system.
Spatial audio attempts to artificially recreate the experience of listening to sounds i...[Details]
1 Basic Features
In computer control systems and various intelligent instruments and meters composed of single-chip microcomputers (or microprocessors), various external analog signals must be ...[Details]
1 Introduction
Ultrasound refers to elastic vibration with a frequency higher than the audible frequency limit (i.e., in the frequency band above 20 kHz). The propagation process of this vib...[Details]
The installation locations of DC-DC converters are relatively scattered. DC-DC converters can be found on the power board, main board, logic control board and other circuit boards of PDP color TVs....[Details]
In recent years, with the increasing maturity of LED technology, LED light sources have been increasingly widely used due to their advantages of using low-voltage power supply, low energy consumpti...[Details]
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
